IOLITE Tech specs

Technical Drawings

IOLITEd Single Channel
 
IOLITEd Single Channel
IOLITEd Multi-channel

IOLITE technical drawing
IOLITE technical drawing
IOLITE technical drawing
IOLITE technical drawing

IOLITE technical drawing
IOLITE technical drawing
IOLITE technical drawing
IOLITE technical drawing

IOLITEd System Specifications

Interface IOLITE Single channel IOLITE Multi channel
Data interface EtherCAT EtherCAT
Data Rate 100 Mbps Full Duplex bus speed 100 Mbps Full Duplex bus speed
Synchronization 1 µs 1 µs
Bus connectors Ethernet RJ45 Ethernet RJ45
Max. cable length between devices 100 m 100 m
Max. Throughput per Chain From 6 MB/s to 10 MB/s (see 1) From 6 MB/s to 10 MB/s
Data interface connection Ethernet RJ45, Single cable for data, power and sync, daisy chainable Ethernet RJ45, single cable for data and sync, daisy chainable (see 2)
Power
Power supply 9 V - 48 V 9 V - 48 V
Power consumption ~2 W (see individual modules) ~4 W (see individual modules)
Power supply connector SCDN-THR 3.81/04/90G 3.2SN BK BX
Environmental
Operating Temperature -20 to 60 °C -40 to 85 °C
Storage Temperature -20 to 60 °C -40 to 85 °C
Humidity 95 %, no condensation 95 %, no condensation
IP rating IP20 IP20
Physical
Dimensions 82 x 62 x 52 mm (might differ for different modules) 137 x 119 x 35 (might differ for different modules)
Weight 130 g (might differ for different modules) 530 g (might differ for different modules)
1) 55 per chain (@ 20 kS/s total sample rate per device), multiple chains possible. Additional power injectors are necessary.
2) Power and data are separated. Daisy-chain for data is available with Ethernet RJ45 cable, Daisy-chain for power is available with T3B2m-T3B2m-0.1m cable
Rev: 1619690400

IOLITEd Single-channel Modules Tech Specs

Amplifiers Overview

1xACC 1xSTG 4xDI 4xDO 1xAO
Input / Output types Input: Voltage, IEPE
Input: Voltage, Strain
Input: Digital Output: Digital Output: Voltage
Number of channels per module
1 1 4 4 1
Connector BNC DB9 DSUB15HD male
DSUB15HD female
BNC
Data rate per channel 40 kS/s 40 kS/s 20 kS/s
Resolution 24-bit 24-bit Digital Digital 18-bit
Bandwidth 0.49 fs 0.49 fs X X X
Alias-free Bandwidth 0.453 fs 0.453 fs X X X
Alias Rejection -100 dB (all sample rates) -100 dB (all sample rates) X X X
Delay Through ADC 37 / fs 37 / fs X X X
Oversampling 32 32 X X X
Voltage ranges ±10 V, ±5 V, ±1 V, ±200 mV ±50 V, ±10 V, ±1 V, ±100 mV Digital (Low: < 1 V, High: > 2 V) X ±10 V
Isolation 125 Vrms Isolation CH, GND 125 Vrms Isolation CH, GND CH-CH, GND-GND CH-GND X
Power supply 12-48V 12-48V 12-48V 12-48V 12-48V
Power consumption 2W 2.5W 2.5W 2.5W 2W
Operating temperature -20..60 °C -20..60 °C -20..60 °C -20..60 °C -20..60 °C
Storage temperature -20..60 °C -20..60 °C -20..60 °C -20..60 °C -20..60 °C
Dimensions 82 x 62 x 28 mm 71 x 62 x 28 mm 71 x 62 x 28 mm 71 x 62 x 28 mm 82 x 62 x 28 mm
Weight 130 g 130 g 130 g 130 g 130 g
Rev: 1593518446
1xACC
 
1xACC
1xSTG
4xDI
4xDO
1xAO
3xMEMS
Analog inputs
Input types Voltage, IEPE
Number of channels 1
Input connector BNC
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate 40 kS/s
Voltage Ranges ±10 V ±5 V ±1 V ±200 mV
Typ. Input Accuracy ±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
90 dB 90 dB 89 dB 88 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
113 dB 110 dB 109 dB 106 dB
Typ. Noise floor @ 10 kS/sec -100 dB -99 dB -99 dB -98 dB
Typical CMR @ 400 Hz / 1 kHz 130 dB / 120 dB
122 dB / 119 dB
104 dB / 97 dB 90 dB / 84 dB
Gain Drift typ. 10 ppm/K (max. 40 ppm/K)
Offset Drift typ. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity < 0.02 %
Input Coupling DC, AC 0.1 Hz, 1 Hz
Input Impedance 1 MΩ
Overvoltage Protection In+ to In-: 50 V continuous, 200 V peak (10 msec)
Isolation 125 Vrms channel to ground isolation
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
IEPE input
Excitation 4 mA, 8 mA
Compliance voltage 24 V
Output Impedance
Sensor detection Shortcut: <4 V; Open: >19 V
TEDS support IEPE mode only
Power
Power consumption 2 W
Environmental
IP rating IP20
Physical
Dimensions 82 x 62 x 28 mm
Weight 130 g
Rev: 1593518446
Analog input - Voltage
Input types Voltage, current, full bridge strain, half bridge strain, quarter bridge strain
Number of channels 1
Input connector DB9
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate 40 kS/s
Voltage Ranges ±50 V ±10 V ±1 V ±100 mV
Typ. Input Accuracy ±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
89 dB 88 dB 88 dB 87 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
100 dB 110 dB 130 dB 145 dB
Typ. Noise floor @ 10 kS/sec -103 dB -99 dB -103 dB -96 dB
Typical CMR @ 400 Hz / 1 kHz 71 dB / 66 dB 72 dB / 66 dB 96 dB / 88 dB 96 dB / 87 dB
Gain Drift typ. 10 ppm/K (max. 40 ppm/K)
Offset Drift typ. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity < 0.02 %
Input Coupling DC, AC 1 Hz
Input Impedance Range ≥ 10 V; 1 MΩ between IN+ and IN-
Range < 10 V: 20 MΩ
Overvoltage Protection Range ≥ 10 V; 200 V
Range < 10 V: 50 V
Isolation 125 Vrms channel to ground isolation
TEDS support Standard + DSI adapters
Analog input - Current
Current ranges 2 mA, 20 mA
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt resistor 50 Ω
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Excitation voltage
Excitation voltage Free programmable (16-bit DAC)
Predefined Levels Unipolar 0 - 24 V, Bipolar 0 - 12 V
Accuracy ±0.05 % ±2 mV
Drift ±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load <0.01 %
Current Limit 42 mA (400 mW max. Power)
Protection Continuous short to ground
Bridge Connection Types full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Bridge ranges 20…10000 mV/V free programmable
Internal Bridge Completion ½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy 0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor 100 kΩ (others on request)
Shunt Resistor Accuracy 0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust Software-selectable
Power
Power consumption 2.5 W
Environmental
IP rating IP20
Physical
Dimensions 71 x 62 x 28 mm
Weight 130 g
Rev: 1593518446
Digital Input
Input type Digital
Number of channels 4
Connector DSBU15HD Male
Compatibility TTL / CMOS Voltage Levels
Input low level UIN < 1 V
Input high level UIN > 2 V
Input high current @ 5 V UIN 3 mA typ.
Input high current @ 30 V UIN 6 mA typ.
Propagation delay < 1 μs
Max. sampling rate 40 kS/sec
Overvoltage protection 30 V Continuous, 65 V peak
Isolation Galvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V 5 V +/- 10 %, 300 mA max.
Output Voltage +12 V 12 V +/-10 %, 100 mA max.
Output Voltage +Vecat
EtherCAT Bus Supply Voltage, 200 mA max.
Power
Power consumption 2.5 W
Environmental
IP rating IP20
Physical
Dimensions 71 x 62 x 28 mm
Weight 130 g
Rev: 1593518446
Digital Output
Output type Digital
Number of channels 4
Connector DSUB15HD Female
Maximum update rate depends on EtherCAT master cycle time
Output type open collector with active internal pullup to 5 V
Sink max 50 V, 2 A (resistive load, unprotected)
Source 5 V, max. 40 mA (internally limited)
Max. switching frequency for internal PWM
100 kHz
Isolation Galvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V
5 V +/- 10 %, 300 mA max.
Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Output Voltage +12 V
12 V +/-10 %, 100 mA max.
Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Output Voltage +Vecat EtherCAT Bus Supply Voltage, 200 mA max. (see 1.)
Power
Power consumption 2.5 W
Environmental
IP rating IP20
Physical
Dimensions 71 x 62 x 28mm
Weight 130 g
Rev: 1593518446
Analog Output
Output types Voltage
Number of channels 1
Output connector BNC
DAC Resolution 18-bit
Update Rate 1000 S/sec (see 1)
Full Scale Output Range ±10 V (see 2)
Accuracy (typ.) 0.1 % ±1 mV (0 to 20 mA load)
Temperature gain drift (typ.) ±10 ppm/K
Temperature offset drift (typ.) ±5 uV/K
SNR @ 1000 S/s output rate 92 dB (sine wave, 250 Hz, ±9 V)
THD -90 dB
Output impedance 0.45 Ω DC
Maximum output current 20 mA
Settling time (0.05 % of set value) 30 μs @ 1000 Ω load, -10 V to 10 V step
Max slew rate 2.5 V/μs @ 1000 Ω load
Max capacitive load (2 % overshoot) 10 nF
Maximum load 500 Ω
Output protection Short circuit protected
Isolation X
Power
Power consumption 2 W
Environmental
IP rating IP20
Physical
Dimensions 82 x 62 x 28 mm
Weight 130 g
1) Only asynchronous mode is supported in Dewesoft, function generator is not supported
2) Only DC output voltage, function generator not supported
Rev: 1593518446
MEMS Accelerometer 3xMEMS-ACC-8g 3xMEMS-ACC-40g
Min. Typ. Max. Min. Typ. Max.
Measurement ranges +-2 g +-8 g +-10 g +-40 g
-3 dB bandwidth 1000 Hz 1000 Hz
Sample rate 4 kHz 4 kHz
Dynamic range 96 dB 96 dB
Noise density (lowest range) 25 µg/√Hz 75 µg/√Hz
Residual noise (+-2 g range, 50 Hz bandwidth)
100 µg RMS
Residual noise (+-2 g range, 125 Hz bandwidth)
150 µg RMS
Offset error -25 mg 10 mg 25 mg -100 mg 30 mg 100 mg
Offset temperature drift (-20 .. 60 degC) -0.15 mg / degC
+-0.02 mg / degC
0.15 mg / degC -0.75 mg / degC +-0.2 mg / degC 0.75 mg / degC
Semsitivity temperature drift (-20 .. 60 degC) +-0.01 % / degC +-0.01 % / degC
Linearity error (smallest range) 0.1 % FS 0.1 % FS
Crossaxis sensitivity -1 % 1 % 1 %
MEMS Inclinometer Typ
Accuracy and resolution valid in range +-15 deg
Accuracy and resolution valid for bandwidth < 0.1 deg
Relative accuracy (23 degC) 0.01 deg
Resolution 0.001 deg

IOLITEd Multi-channel Modules Tech Specs

Amplifiers Overview

6xSTG 8xSTGS 8xLV 16xLV 8xLA 8xTH 8xRTD 8xRTDp 32xDI 32xDO 8xDI-4xDO 4xCNT 16xAO
Connectors DB9 Terminal block, DB37 BNC, Terminal block Terminal block BNC, Terminal block Thermocouple L0B6f, Terminal block L0B6f Terminal block Terminal block Terminal block L1B7f Terminal block
#ch per module 6x 8x 8x 16x 8x 8x 8x 8x 32x 32x 8x digital in, 4x digital out 4x 16x
Data rate / channel 20 kS/sec 20 kS/sec 20 kS/sec 20 kS/sec 20 kS/sec 100 S/sec 100 S/sec 100 S/sec 20 kS/sec 20 kS/sec 20 kS/sec
Resolution 24-bit 24-bit 24-bit 24-bit 24-bit 24-bit 24-bit 24-bit digital digital digital
100 MHz
timebase
5 ppm,
20 ppm max
16-bit
Bandwidth 0.49*fs 0.433*fs 0.49*fs 0.433*fs 0.49*fs 10 MHz
Voltage ranges ±50 V, ±10 V, ±1 V, ±100 mV ±1 V, ±100 mV, ±20 mV ±100 V, ±10 V
(±10 V, ±1 V on request)
±200 V, ±10 V
(±20 V, ±1 V on request)
±1 V, ±100 mV ±1 V, ±100 mV ±1 V, ±100 mV open collector TTL
(Low: <0.8 V,
High > 2 V)
±10 V
Input coupling DC, AC 1 Hz DC DC DC DC DC DC DC
Sensor excitation 0..12 V (bipolar), 0..24 V (unipolar) max. 0.4 W/ch 1 V, 2 V, 5 V 5 V, 12 V
Bridge connection Full, ½, ¼ 350 Ω, ¼ 120 Ω 3-wire Full, ½, ¼ 350 Ω, ¼ 120 Ω 3-wire
Programmable shunt 100 kΩ 100 kΩ
IEPE input DSI-ACC
Current 20 mA (internal shunt), DSI-5A ±20 mA, ±2 mA
Temperature (PTx) DSI-RTD PT100, 200, 500, 1000, 2000 PT100, 200, 500, 1000, 2000
Thermocouple DSI-TH K, J, T, R, S, N, E, C, U, B
Resistance 1 kΩ, 10 kΩ 1 kΩ, 10 kΩ
Potentiometer
LVDT DSI-LVDT
Charge DSI-CHG
TEDS ✓ (except DB37)
Isolation voltage Differential Differential 450 V 250 V 450 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V
Power consumption per module Typ. 5.4 W,
Max. 11.1 W
Typ. 2.7 W,
Max. 5.1 W
Typ. 2.4 W,
Max. 3.5 W
Typ. 3.4 W,
Max. 4.2 W
Typ. 2.4 W,
Max. 3.5 W
3.2 W Typ. 2.1 W,
Max. 2.7 W
Typ. 2.1 W,
Max. 2.7 W
Typ. 1.2 W,
Max. 1.9 W
Typ. 1.2 W,
Max. 2.0 W
Typ. 1.1 W,
Max. 1.8 W
Typ. 1.9 W Typ. 4.3 W,
Max. 7.2 W
Advanced functions Supports all strain types, high input range Supports all strain types, low power consumption High isolation, high input range High isolation, high input range High isolation, high input range High isolation, support of main TC types High isolation Pulsed excitation, Cryogenic temperature range, High isolation Watchdog High sink current, watchdog Supercounter technology
Rev: 1615363200

IOLITE I/O Modules Specifications

6xSTG
 
6xSTG
8xSTGS
8xLV
16xLV
8xLA
8xTH
8xRTD
8xRTDp
32xDI
32xDO
8xDI-4xDO
4xCNT
Analog inputs
Input type Voltage
Full / half / quarter bridge strain
Current
Potentiometer
Resistance
Number of channels 6
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate Simultaneous 20 kS/sec per channel (software-selectable)
Voltage Ranges ±50 V ±10 V ±1 V ±100 mV
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS -100 dB -110 dB -130 dB -145 dB
Typical Noise floor @ 10 kS -103 dB -97 dB -103 dB -94 dB
Typical CMR @ 400 Hz / 1 kHz 71 dB / 66 dB 72 dB / 66 dB 96 dB / 88 dB 96 dB / 87 dB
Gain Drift Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity < 0.02%
Input Coupling DC, AC 1Hz
Input Impedance 1 MΩ 1 MΩ 20 MΩ 20 MΩ
Overvoltage Protection In+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog inputs - Current
Current ranges 20 mA 2 mA
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor 50 Ω
Analog input performance
Bandwidth (-3 dB) 0.49*fs
Alias-free Bandwidth DC to 0.453*fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Excitation Voltage
Excitation Voltage Free programmable (16-bit DAC)
Predefined Levels Bipolar: 0, 1, 2, 5, 10 and 12 VDC
Unipolar: 0, 2, 5, 10, 15, 24 VDC
Accuracy ±0.05 % ±2 mV
Drift ±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load < 0.01 %
Current Limit 42 mA (550 mW max. power)
Protection Continuous short to ground
Excitation Current
Excitation Voltage Free programmable (16-bit DAC)
Predefined Levels 0, 2, 4, 8, 16, 44 mA
Accuracy ±0.1 % ±2 μA (<10 mA), ±0.5 % ±5 μA (>10 mA)
Bridge measurement
Bridge Connection Types full bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges 2…1000 mV/V free programmable
Internal Bridge Completion ½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy 0.05 %; TCR: 5 ppm/K (others on request)
Internal Shunt Resistor 100 kΩ (others on request)
Shunt Resistor Accuracy 0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust Software-selectable
Additional Specifications
Input connectors D-SUB9
TEDS support Standard + DSI adapters
Power supply 9 - 48 V DC
Power Consumption 5.4 W, Max. 11.1 W (7.9 W 120 Ω @ 5 V load, 8.8 W 350 Ω @ 10 V load)
Weight 340 g
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1620029200
Analog inputs
Input type Full / half / quarter bridge strain (3-wire), Potentiometer
Number of channels 8
ADC Type 24-bit oversampled sigma-delta with anti-aliasing filter
Sampling Rate Simultaneous 20 kS/sec per channel (software-selectable)
Voltage Ranges ±1 V ±100 mV ±20 mV
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Noise floor @ 10 kS/s / 1 kS/s / 100 S/s
-107 / -114 / -122 dB -99 / -107 / -117 dB -87 / -96 / -108 dB
Typical Dynamic Range @ 10 kS/s / 1 kS/s / 100 S/s
-134 / -133 / -133 dB -131 / -130 / -129 dB -121 / -119 / -120 dB
Typ. Crosstalk @ 1 kHz -120 dB -126 dB -114 dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz 84 / 85 / 76 dB 108 / 104 / 99 dB 118 / 117 / 113 dB
Gain Drift Typical 10 ppm/K (max. 20 ppm/K)
Offset Drift Typical 0.03 μV/K + 2.5 ppm of range/K, max 0.1 μV/K + 9 ppm of range/K
Gain Linearity < 0.02 %
Input Coupling DC
Analog input performance
Bandwidth (-3 dB) 0.433*fs (Sinc5 filter 0.204*fs)
Alias-free Bandwidth DC to 0.499*fs
Alias Rejection -105 dB (all sample rates)
Delay Through ADC 34 / fs (Sinc5 filter 3 / fs)
Oversampling 128
Excitation Voltage
Excitation Voltage Unipolar: 1 V, 2 V, 5 V (see 1)
Current Limit 42 mA
Protection Continuous short to ground
Bridge measurement
Bridge Connection Types full bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges 2 mV/V, 20 mV/V, 200 mV/V (2 mV/V ... 1000 mV/V free programmable)
Internal Bridge Completion ¼ bridge 120Ω and 350 Ω
Bridge Completion Accuracy 0.05 %; TCR: 5 ppm/K (others on request)
Internal Shunt Resistor 100 kΩ software selecteable to SNS+ or SNS- and In+ or In-
Shunt Resistor Accuracy 0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust Software-selectable
Additional Specifications
Input connectors Terminal block, D-SUB37, D-SUB9 Micro-D
TEDS support Available for Terminal block, D-SUB9 Micro-D (see 2)
Power supply 9 - 48 V DC
Power Consumption Typ. 2.7 W, Max. 5.1 W (120 Ω @ 5 V load)
Weight 340 g
Slice Dimensions 128.4 x 118.4 x 30.14 mm
1) Ratiometric method
2) Not compatible with DSI adapters
Analog input IOLITEi-8xLV
Input type Isolated voltage
Number of channels 8
ADC Type 24-bit oversampled SAR
Sampling Rates Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Range ±100 V ±10 V
Accuracy ±0.03 % of reading ±50 mV ±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)
91 dB 90 dB
Typical noise floor @ 10 kS -105 dB -98 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)
-91 dB -91 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)
93 dB 92 dB
Typical CMR @ 400 Hz / 1 kHz 98 dB / 90 dB 83 dB / 75 dB
Gain Drift Typical 10 ppm/K, Max. 40 ppm/K
Offset Drift Typical 2 ppm of range/K, Max. 10 ppm of range/K
Gain Linearity < 0.02 %
Input Coupling DC
Input Impedance 1 MΩ
Overvoltage Protection In+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB) 0.49*fs
Alias-free Bandwidth DC to 0.453*fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Additional Specifications
Power supply 9 - 48 V DC
Isolation Voltage 450 Vpeak channel to ground & channel to channel
Power Consumption Typ. 2.4 W, Max. 3.5 W
Input Connectors BNC
Terminal block 2 pole
OMNIMATE SL 2.50 / BLF 2.50/180
Weight 310 g 270 g
Slice Dimensions 128.4 x 127.6 x 30.1 mm 128.4 x 115.4 x 30.1 mm
Rev: 1615363200
Analog input IOLITE-16xLV
Input type Voltage
Number of channels 16
ADC Type 24-bit oversampled sigma-delta
Sampling Rates Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Range ±200 V ±10 V
Accuracy ±0.03 % of reading ±40 mV ±0.03 % of reading ±2 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)
103 dB 101 dB
Typical noise floor @ 10 kS -109 dB -104 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)
-93 dB -108 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)
95 dB 111 dB
Typical CMR @ 400 Hz / 1 kHz -88 dB / -87 dB -82 dB / -80 dB
Crosstalk @ 1 kHz -118 dB -120 dB
Gain Drift Typical 10 ppm/K, Max. 40 ppm/K
Offset Drift Typical 2 ppm of range/K, Max. 5 ppm of range/K
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 800 kΩ
Overvoltage Protection In+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB) 0.433*fs
Alias-free Bandwidth 0.499*fs
Alias Rejection -105 dB (all sample rates)
Delay Through ADC 34 / fs (Sinc5 filter 3 / fs)
Oversampling 128
Additional Specifications
Power supply 9 - 48 V DC
Isolation Voltage 250 V functional isolation
(channel to power supply ground)
Power Consumption Typ. 3.4 W (Max. 4.2 W)
Input Connectors Terminal block 9 pole
OMNIMATE SL 2.50 / BLF 2.50/180
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Weight 230 g
Rev: 1614067200
Analog input IOLITEi-8xLA
Input type Isolated current
Number of channels 8
ADC Type 24-bit oversampled SAR
Sampling Rates Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Current Range ±20 mA ±2 mA
Accuracy ±0.05 % of reading ±10 µA ±0.05 % of reading ±2 µA
Typical noise floor @ 10 kS/sec -100 dB -100 dB
Crosstalk (20 kS/sec, -1 dBFS @ 1 kHz)
-121 dB -128 dB
Gain Drift Typical 10 ppm/K, Max. 40 ppm/K
Offset Drift Typical 5 ppm of range/K, Max. 15 ppm of range/K
Gain Linearity < 0.05 %
Input Coupling DC
Input Impedance 50 Ω
Overvoltage Protection In+ to In-: 20 V continuous, 30 Vpeak (100 ms)
Overcurrent Protection In+ to In-: 70 mA continuous
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Additional Specifications
Power supply 9 - 48 V DC
Isolation Voltage 450 Vpeak channel to ground & channel to channel
Power Consumption Typ. 2.8 W, Max. 3.5 W
Input Connectors BNC
Terminal block 2 pole
OMNIMATE SL 2.50 / BLF 2.50/180
Weight 310 g 270 g
Slice Dimensions 128.4 x 127.6 x 30.1 mm 128.4 x 115.4 x 30.1 mm
Rev: 1615363200
Inputs
Input type Isolated universal thermocouple and voltage
Number of channels 8
ADC Type 24-bit delta-sigma
Sampling Rate Simultaneous 100 S/sec
Voltage Ranges ±1 V ±100 mV
Input Accuracy ±0.02 % of reading ±100 μV ±0.02 % of reading ±10 μV
Typical Noise floor @ 10/100 S/sec -114 dB / -105 dB -109 dB / -100 dB
Gain Drift Typical 4 ppm/K (max. 10 ppm/K)
Offset Drift Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity <0.01%
Input Coupling DC
Input Impedance 100 MΩ
Thermocouple TC Types: K, J, T, R, S, N, E, C, B
Accuracy ±0.02 % of reading ±0.5 °C ±10 μV
Resolution < 0.001 °C
Sampling rates 10, 20, 40, 80, 100 S/sec
Typical Noise 0.007 °C [email protected] K @ 10 S/sec
0.02 °C [email protected] K @ 100 S/sec
Additional Specifications
Input connectors Mini Thermocouple connector (copper)
Isolation voltage 1000 Vpeak channel to ground & channel to channel
Power supply 9 - 48 V DC
Power consumption 3.2 W
Weight 230 g
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1578677400
Analog inputs
Input types voltage, resistor or universal PTxxx inputs
Number of channels 8
ADC Type 24-bit delta-sigma
Sampling Rate Simultaneous 100 S/sec
Voltage Ranges ±1 V ±100 mV
Input Accuracy
±0.02 % of reading ±0.01 % of range ±10 μV
±0.02 % of reading ±0.01 % of range ±10 μV
Typical Noise floor @ 10/100 s/sec
-117 dB / -107 dB -111 dB / -101 dB
Gain Drift Typical 4 ppm/K (max. 10 ppm/K)
Offset Drift Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 1 MΩ
Temperature PT500, PT1000, PT2000 PT100, PT200
Measurement range -200 °C to +850 °C
Accuracy ±0.05 % of reading ±0.2 °C
Temperature Drift typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection 3-wire or 4-wire
Resolution < 0.001 °C
Resistance 0…10 kΩ 0…1 kΩ
Accuracy ±0.02 % of reading ±0.01 % of range
Input Connection 3-wire or 4-wire
Additional Specifications
Input connectors Lemo 0B 6pin EEA.0B.306.CLN, Terminal Block Weidmueller SL 2.50-04
Isolation voltage 1000 Vpeak channel to ground & channel to channel
Power supply 9 - 48 V DC
Power consumption Typ. 2.1 W, Max. 2.7 W
Weight 260 g
Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1568244600
Analog inputs
Input types voltage, resistor or universal PTxxx inputs
Number of channels 8
ADC Type 24-bit delta-sigma
Sampling Rate Simultaneous 100 S/sec
Voltage Ranges ±1 V ±100 mV
Input Accuracy
±0.02 % of reading ±0.01 % of range ±10 μV
±0.02 % of reading ±0.01 % of range ±10 μV
Typical Noise floor @ 10/100 s/sec
-117 dB / -107 dB -111 dB / -101 dB
Gain Drift Typical 4 ppm/K (max. 10 ppm/K)
Offset Drift Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 1 MΩ
Temperature PT200, PT500, PT1000, PT2000 PT100
Excitation current 0.4 mA or ±0.4 mA 2 mA or ±2 mA
Excitation type DC or DC squared from 5Hz to 50Hz
Measurement range -200 °C to +850 °C
Accuracy ±0.05 % of reading ±0.2 °C
Temperature Drift typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection 2-wire, 3-wire or 4-wire
Resolution < 0.001 °C
Resistance 0…10 kΩ 0…1 kΩ
Excitation current 0.4 mA or ±0.4 mA 2 mA or ±2 mA
Excitation type DC or DC squared from 5Hz to 50Hz
Accuracy ±0.02 % of reading ±0.01 % of range
Input Connection 2-wire, 3-wire or 4-wire
Additional Specifications
Input connectors Lemo 0B 6pin EEA.0B.306.CLN
Isolation voltage 1000 Vpeak channel to ground & channel to channel
Power supply 9 - 48 V DC
Power consumption Typ. 2.1 W, Max. 2.7 W
Weight 260 g
Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1568244600
Digital Input
Isolated Input Channels 32
Input low level -1 V ~ +1 V
Input high level -48 V ~ -3 V, +3 V ~ +48 V
Input high current @ 5 V UIN < 1 mA
Input high current @ 30 V UIN < 1 mA
Sampling rate Simultaneous 20 kS/sec
Overvoltage protection 100 V continuous (250 Vpeak)
Isolation voltage peak
1000 V channel to ground & channel to channel
Additional Specifications
Input connectors
Terminal block, 2 pole, 4 x 9 pole
OMNIMATE SL 2.50 / BLF 2.50/180
Power supply 9 - 48 V DC
Power out max. 2 A (unprotected)
Power consumption Typ. 1.2 W, Max. 1.9 W
Weight 220 g
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1566554400
Digital Output
Isolated Output Channels 32
Compatibility Solid state relay
Maximum sink current 0.5 A
Maximum switching voltage 50 V
Maximum update rate depending on EtherCAT master
Isolation voltage peak
1000 V channel to ground, no channel to channel isolation
Additional Specifications
Input connectors
Terminal block, 2 pole, 4 x 9 pole
OMNIMATE SL 2.50 / BLF 2.50/180
Power supply 9 - 48 V DC
Power out max. 2 A (unprotected)
Power consumption Typ. 1.2 W, Max. 2.0 W
Weight 230 g
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Rev: 1566554400
Digital Input
Isolated Input Channels 8
Input low level -1 V ~ +1 V
Input high level -48 V ~ -3 V, +3 V ~ +48 V
Input high current @ 5 V UIN < 1 mA
Input high current @ 30 V UIN < 1 mA
Sampling rate Simultaneous 40 kS/sec
Overvoltage protection 100 V continuous (250 Vpeak)
Isolation voltage peak 1000 V channel to ground & channel to channel
Digital Output
Isolated Output Channels 4
Compatibility Solid state relay
Maximum sink current 0.5 A
Maximum switching voltage
50 V
Maximum update rate depending on EtherCAT master
Isolation voltage peak
1000 V channel to ground, no channel to channel isolation
Additional Specifications
Input connectors
Terminal block (3 x 2 pole, 2 x 12 pole, 1 x 8 pole)
OMNIMATE SL 2.50 / BLF 2.50/180
Power supply 9 - 48 V DC
Power out max. 2 A (unprotected)
Power consumption Typ. 1.1 W, Max. 1.8 W
Weight 184 g
Slice Dimensions 128.4 x 115.4 x 30.1 mm
Counter
Number of channels 4
Timebase 100 MHz
Time base accuracy Typical: 5 ppm, Max: 20 ppm
Max. bandwidth 10 MHz
Input Filter 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level Compatibility TTL (Low: <0.8 V, High >2 V)
Input impedance 100 kΩ pull-up to +3.3 V
Input Protection ±25 V continuous
Sensor supply 5 V / 100 mA, 12 V / 50 mA
Counter modes counting, waveform timing, encoder, gear-tooth sensor
Additional Specifications
Input connector 7-pin LEMO 1B series EEG.1B.307.CLNY
Preliminary: Terminal block OMNIMATE Signal SL Series SL 2.50/09/90G
Power Consumption
Typ. 1.9 W
Power supply 9 - 48 V DC
Slice Dimensions 128.4 x 115.4 x 30.1 mm