Tech specs - KRYPTON

Technical drawings

KRYPTON single width
 
KRYPTON single width
KRYPTON dual width
KRYPTON one

General specifications

Interface
Data interface EtherCAT®
Data Rate 100 Mbps Full Duplex bus speed
Max. Throughput per Chain From 6 MB/s to 10 MB/s
Sync Accuracy below 1 sample to Sirius®
EtherCAT® Max. Cable Length 100 m
Max. Number of Units 64 or more (power injectors may be required)
Data Interface Connection
LEMO 1T EtherCAT® hybrid cable
Single cable for data, power and sync, daisy chainable
Power
Power Supply 9 - 48 V DC
Environmental
Operating Temperature -40 to 85°C
Storage Temperature -40 to 85°C
Humidity 5 to 100 % RH
IP rating IP65 / IP67
Shock
Shock: SIST EN 60068-2-27:2009
100 g, 6 ms, half-sine
100x pos./neg in each axis
600x total
Vibration
Random vibration: MIL-STD-202G Method 214A, test condition II-D
Profile break points:
50 Hz @ 0.025 g²/Hz
100 Hz @ 0.1 g²/Hz
2000 Hz @ 0.1 g²/Hz
Profile RMS / Peak = 13.9 g / 41.7 g
8 hrs in each axis, 24 hrs total
Rev: 1593507600

Multi-channel units specification

Amplifier overview

STG TH RTD ACC LV LA DIO
Connectors DB9, L2B10f Thermocouple L0B6f BNC BNC BNC DB25
#ch per module 3x, 6x 8x, 16x 8x 4x, 8x 4x, 8x 8x 16xDI, 16xDO 8xDI, 8xDO
Data rate / channel 20 kS/sec 100 S/sec 100 S/sec 20 kS/sec 20 kS/sec 20 kS/sec 20 kS/sec
Resolution 24-bit digital
Bandwidth 0.49 fs 0.49 fs 0.49 fs 0.49 fs
Voltage ranges ±10 V, ±1 V, ±100 mV, ±10 mV ±1 V, ±100 mV ±1 V, ±100 mV ±10 V, ±5 V, ±1 V, ±200 mV ±50 V ±20 mA CMOS compatible
Input coupling DC DC DC DC, AC 0.1 Hz, 1 Hz DC DC DC
Sensor excitation 0...15 V max. 0.4 W/ch (45 mA limit) IEPE 4 mA, 8 mA 5 V / 300 mA
12 V / 120 mA
Vsupply / 200 mA
Bridge connection Full, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire
Programmable shunt 100 kΩ
IEPE input DSI-ACC
Resistance 10 kΩ
Temperature (PTx) DSI-RTD PT100, 200, 500, 1000, 2000
Thermocouple DSI-TH K, J, T, R, S, N, E, C, B
Potentiometer
LVDT DSI-LVDT
Charge DSI-CHG
Current ext. shunt
DSI-20mA, DSI-5A
ext. shunt
TEDS
Isolation voltage Differential 1000 V 1000 V Differential 1000 V 1000 V 250 V
Power consumption per module 2.4 W (4 W 120 Ω @ 5 V load) 3xSTG;
5.9 W (8.9 W 120 Ω @ 5 V load) 6xSTG
2.5 W (8xTH)
4 W (16xTH)
2.5 W 4.6 W
3.5 W (4xLV)
6.7 W (8xLV)
6.8 W 2 W
Advanced functions Supports all strain types, TEDS support High isolation, support of main TC types High isolation TEDS support High isolation, high input range High isolation, 4-20 mA current loop
Rev: 1578553200
LV
 
LV
LA
DIO
TH
RTD
STG
ACC
Analog input KRYPTONi-4xLV KRYPTONi-8xLV
Input type Isolated voltage
Number of channels 4 8
ADC Type 24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rates Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/sec (software-selectable)
Voltage Range ±50 V
Accuracy ±0.03 % of reading ±5 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
104 dB
Typical noise floor @ 10 kS/sec -106 dB
Type. THD (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
-104 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
105 dB
Typical CMR @ 400 Hz / 1 kHz 105 dB / 94 dB
Gain Drift Typical 10 ppm/K, max. 20 ppm/K
Offset Drift Typical 5 μV/K, max. 10 μV/K
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 1 MΩ
Noise 0.7 mVRMS
Overvoltage Protection In+ to In-: 200 V continuous, 350 Vpeak (100 msec)
Analog input performance
Bandwidth (-3dB) 0.49 fs
Alias-free Bandwidth Bandwidth (-3 dB)
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Additional Specifications
Input Connector BNC
Isolation Voltage 1000 Vpeak channel/ground & channel/channel
Environmental Rating (see 1) IP67
Amplifier type KRYPTONi-4xLV KRYPTONi-8xLV
Power Consumption 3.8 W 6.8 W
Weight 700 g 1000 g
Slice Dimensions 213 x 39 x 56 mm 213 x 54 x 56 mm
Dimensions with Connectors 213 x 39 x 66.8 mm 213 x 54 x 66.8 mm
1) Depending on the mating connector types
Analog input KRYPTONi-8xLA
Input type Isolated current
Number of channels 8
ADC Type 24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rates
Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/sec (software-selectable)
Current Range ±20 mA
Accuracy ±0.02 % of reading ±8 µA
Typical noise floor @ 10 kS/sec -95 dB
Crosstalk (20 kS/sec, -1 dBFS @ 1 kHz) -124 dB
Gain Drift Typical 10 ppm/K, max. 20 ppm/K
Offset Drift Typical 100 nA/K, max. 200 nA/K
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 50 Ω
Noise 0.3 µARMS
Overvoltage Protection 50 V
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Additional Specifications
Input Connector BNC
Isolation Voltage 1000 Vpeak channel/ground & channel/channel
Environmental Rating (see 1) IP67
Amplifier type
Power Consumption 6.8 W
Weight 1000 g
Slice Dimensions 213 x 54 x 56 mm
Dimensions with Connectors 213 x 54 x 66.8 mm
1) Depending on the mating connector types
KRYPTONi-16xDI KRYPTONi-8xDI-8xDO KRYPTONi-16xDO
Digital Input
Isolated Input Channels 16 8
Compatibility CMOS Configuration
Input low level UIN < 0.8 V
Input high level UIN > 2.4 V
Input high current @ 5 V UIN < 1.8 mA
Input high current @ 30 V UIN < 6 mA
Propagation delay < 1 μs
Sampling rate Simultaneous 20 kS/sec
Overvoltage protection 40 V continuous (65 V peak)
Isolation voltage peak 250 V channel/ground & channel/channel
Digital Output
Isolated Output Channels 8 16
Compatibility Open collector with 10 kΩ pull-up to +5 V
Maximum sink current 150 mA (not protected)
Maximum switching voltage 50 V
Propagation delay < 20 μs
Maximum update rate depending on EtherCAT master
Isolation voltage peak 250 V channel to ground, no channel to channel isolation
General Specifications
Environmental rating IP67
Power consumption 2 W
Weight 700 g
Slice Dimensions 213 x 39 x 56 mm
Dimensions with Connectors 213 x 39 x 58.2 mm
Analog inputs KRYPTONi-8xTH KRYPTONi-16xTH
Input type Isolated universal thermocouple and voltage
Number of channels 8 16
ADC Type 24-bit delta-sigma
±0.02 % of reading ±10 μV Simultaneous 100 S/sec
Voltage Ranges ±1 V ±100 mV
Input Accuracy ±0.02 % of reading ±100 μV ±0.02 % of reading ±10 μV
Typical Noise Floor @ 10 / 100 S/sec -114 dB / -105 dB -109 dB / -100 dB
Gain Drift Typical 3 ppm/K (max. 10 ppm/K)
Offset Drift 0.03 μV/K
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 100 MΩ
Thermocouple
Input type TC Types: K, J, T, R, S, N , E, C, B
Accuracy ±0.02 % of reading ± 0.5 °C ± 10 μV
Resolution < 0.001 °C
Sampling rates 100, 80, 40, 20, 10 S/sec
Typical Noise 0.007 °C RMS @ Type K @ 10 S/sec 0.02 °C RMS @ Type K @ 100 S/sec
Additional Specifications
Input connector Mini Thermocouple connector (copper)
Isolation voltage 1000 Vpeak channel/ground & channel/channel
Environmental rating (see 1) IP67
Amplifier type KRYPTONi-8xTH KRYPTONi-16xTH
Power consumption 2.5 W 4 W
Weight 720 g 1000 g
Dimensions 213 x 39 x 56 mm 213 x 54 x 56 mm
1) Depending on the mating connector types, for non corrosive liquids only, IP65 standard

KRYPTON TH accuracy

Temperature Type K Type J Type T Type R Type S Type N Type E Type B Type C
-200 °C 1.19 °C 1.00 °C 1.18 °C 1.52 °C 0.95 °C
-100 °C 0.84 °C 0.76 °C 0.87 °C 0.99 °C 0.74 °C
0 °C 0.75 °C 0.70 °C 0.76 °C 2.35 °C 2.32 °C 0.88 °C 0.67 °C 1.22 °C
100 °C 0.76 °C 0.70 °C 0.73 °C 1.83 °C 1.87 °C 0.85 °C 0.67 °C 11.62 °C 1.14 °C
400 °C 0.81 °C 0.76 °C 0.73 °C 1.53 °C 1.61 °C 0.84 °C 0.70 °C 2.98 °C 1.09 °C
700 °C 0.88 °C 0.79 °C 1.46 °C 1.56 °C 0.88 °C 0.76 °C 2.04 °C 1.14 °C
1000 °C 0.97 °C 0.86 °C 1.42 °C 1.53 °C 0.95 °C 0.84 °C 1.70 °C 1.25 °C
1300 °C 1.09 °C 1.42 °C 1.54 °C 1.03 °C 1.57 °C 1.39 °C
1700 °C 1.55 °C 1.69°C 1.57 °C 1.63 °C
Analog inputs KRYPTONi-8xRTD
Input types voltage, resistor or universal Ptxxx inputs
Number of channels 8
ADC Type 24-bit delta-sigma
Sampling Rate Simultaneous 100 S/sec
Voltage Ranges ±1 V ±100 mV
Input Accuracy
±0.02 % of reading ±0.01 % of range ±10 μV
±0.02% of reading ±0.01% of range ±10 μV
Typical Noise floor @ 10/100 s/sec -108 dB / -98 dB -108 dB / -98 dB
Gain Drift Typical 3 ppm/K (max. 10 ppm/K)
Offset Drift Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 1 MΩ
Temperature PT500, PT1000, PT2000 PT100, PT200
Measurement range -200 °C to +850 °C
Accuracy ±0.05 % of reading ±0.2 °C
Temperature Drift typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection 3 wire or 4 wire
Resolution < 0.001 °C
Resistance 0…10 kΩ 0…1 kΩ
Accuracy ±0.02 % of reading ±0.01 % of range
Input Connection 3 wire or 4 wire
Resolution
Additional Specifications
Input connector Lemo 0B 6pin EEA.0B.306.CLN
Isolation voltage 1000 Vpeak channel/ground & channel/channel
Environmental rating (see 1) IP65
Power consumption 2.5 W
Weight 720 g
Dimensions 213 x 39 x 58 mm
1) Depending on the mating connector types
Rev: 1564584000
Analog inputs KRYPTON-3xSTG KRYPTON-6xSTG
Input type Voltage
Full / half / quarter strain
Number of channels 3 6
ADC Type 24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rate Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/sec (software-selectable)
Voltage Ranges ±10 V ±1 V ±100 mV ±10 mV
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS/sec
-139 dB -139 dB -129 dB -110 dB
Typical Noise Floor @ 10 kS/sec -106 dB -105dB -97 dB -78 dB
Typical CMR @ 400 Hz / 1 kHz 86 dB / 84 dB 96 dB / 95 dB 112 dB / 102 dB 112 dB / 102 dB
Gain Drift Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity < 0.02 %
Input Coupling DC
Input Impedance 10 MΩ
Overvoltage Protection In+ to In-: 50 V continuous, 200 V peak (10 ms)
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Excitation Voltage
Excitation voltage Free programmable (16-bit DAC)
Predefined Levels 0, 1, 2.5, 5, 10 and 15 VDC
Accuracy ±0.05 % ±2 mV
Drift ±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load < 0.01 %
Current Limit 45 mA (400 mW max. Power)
Protection Continuous short to ground
Bridge Connection Types full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Ranges 2…1000 mV/V free programmable
Internal Bridge Completion ½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy 0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor 100 kΩ (others on request)
Shunt Resistor Accuracy 0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust Software-selectable
Additional Specifications
Input connector DB9; L2B10f
TEDs support Standard + DSI adapters
Environmental rating IP67
Amplifier type KRYPTON-3xSTG KRYPTON-6xSTG
Power Consumption 3.5 W (4.8 W 120 Ω @ 5 V load) 6xSTG: 5.9 W (8.9 W load 120 Ω @ 5 V)
Weight 740 g 1100 g
Slice Dimensions 213 x 39 x 56 mm 213 x 54 x 56 mm
Dimensions with Connectors 213 x 39 x 58.2 mm 213 x 54 x 58.2 mm
Analog inputs KRYPTON-4xACC, KRYPTON-8xACC
Input type Voltage, IEPE
Number of channels 4 (4xACC), 8 (8xACC)
ADC Type 24-bit delta-sigma with anti-aliasing filter
Sampling Rate Simultaneous 20 kS/sec per channel (software-selectable)
Voltage Ranges ±10 V ±5 V ±1 V ±200 mV
Input Accuracy ±0.03 % of reading ±0.02 % of range ±0.2 mV
Typical Dynamic Range @ 10 kS/sec -140 dB -137 dB -138 dB -134 dB
Typical noise floor @ 10 kS/sec -106 dB -106 dB -106 dB -102 dB
Type. THD (20 kS/sec, -1 dBFS sine wave @ 1 kHz)
-94 dB -94 dB -93 dB -95 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)
96 dB 96 dB 96 dB 93 dB
Gain Drift TBD
Offset Drift TBD
Gain Linearity TBD
Input Coupling DC, AC 0.1 Hz, 1 Hz
Input Impedance 1 MΩ
Overvoltage Protection In+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
IEPE input
Excitation 4 mA, 8 mA
Compliance voltage 25 V
Output Impedance >100 kΩ
Sensor detection Shortcut: <4 V; Open: >19 V
Additional Specifications
Input connector BNC
TEDs support IEPE mode only
Environmental rating (see 1) IP67
Amplifier type KRYPTON-4xACC KRYPTON-8xACC
Power Consumption 3 W 4.6 W
Weight 700 g 1000 g
Slice Dimensions 213 x 39 x 56 mm 213 x 54 x 56 mm
Dimensions with Connectors 213 x 39 x 66.8 mm 213 x 54 x 66.8 mm
1) Depending on the mating connector types

Single-channel units specification

Overview

AO DI DO ACC STG LV HV TH-HV CNT
Input / Output types Output: Voltage Input: Digital Output: Digital
Input: Voltage, IEPE
Input: Voltage, Strain
Input: Voltage Input: Voltage
Input: Thermocouple
Input: Digital
Number of channels per module
1 4 4 1 1 1 1 1 1
Connector BNC DSUB15HD Male DSUB15HD Female BNC DB9 BNC Banana jack K-type
Thermocouple LEMO REDEL
LEMO T-type
7pin female
Data rate per channel 40 kS/sec 40 kS/sec 40 kS/sec 40 kS/sec 40 kS/sec 100 S/sec 20 kS/sec
Resolution 18 bit Digital Digital 24-bit 24-bit 24-bit 24-bit 24-bit
100 MHz
timebase
5 ppm,
20 ppm max
Bandwidth 0.49 fs 0.49 fs 0.49 fs 0.49 fs 0.49 fs 10 MHz
Alias-free Bandwidth 0.453 fs 0.453 fs 0.453 fs 0.453 fs 0.453 fs
Alias Rejection
-100 dB
(all sample rates)
-100 dB
(all sample rates)
-100 dB
(all sample rates)
-100 dB
(all sample rates)
-100 dB
(all sample rates)
Delay Through ADC 37 / fs 37 / fs 37 / fs 37 / fs 37 / fs
Oversampling 32 32 32 32 32
Voltage ranges ±10 V
Digital
(Low: < 1 V,
High: > 2 V)
±10 V
±5 V
±1 V
±200 mV
±50 V
±10 V
±1 V
± 100 mV
±50 V
±10 V
±1 V
±100 mV
±1000 V Thermocouple
TTL
(Low: <0.8 V,
High > 2 V)
Isolation
Galvanic isolation
CH, GND
Galvanic isolation
CH, GND
125 Vrms Isolation
CH, GND
125 Vrms Isolation
CH, GND
125 Vrms Isolation
CH, GND
CAT III 600 V
CAT II 1000 V
CAT III 600 V
CAT II 1000 V
Power supply 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V 9 - 50 V
Power consumption 2 W 1.5 W 2 W 2 W 3 W 1.5 W 1 W 1.3 W 1.2 W
Operating temperature -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C
Storage temperature -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C -40 to 85 °C
Dimensions 62 x 56 x 29 mm 62 x 56 x 29 mm 62 x 56 x 29 mm 62 x 56 x 29 mm 62 x 56 x 29 mm 62 x 56 x 29 mm 62 x 56 x 36 mm 62 x 56 x 36 mm 62 x 56 x 29 mm
Weight 250 g 250 g 250 g 250 g 250 g 250 g 300 g 300 g 250 g
Rev: 1578868200

General specifications

Interface
Data interface EtherCAT®
Data rate 100Mbps Full Duplex bus speed
Sync Accuracy below 1 sample to Sirius®
EtherCAT® Max. Cable Length 100 m
Max. Throughput per Chain From 6 MB/s to 10 MB/s
Max. Number of Units 64 or more (power injectors may be required)
Data Interface Connection
LEMO 1T EtherCAT® hybrid cable
Single cable for data, power and sync, daisy chainable
Power
Power Supply 9 - 50 V DC
Power consumption 1 - 3 W
Environmental
Operating Temperature -40 to 85 °C
Storage Temperature -40 to 85 °C
Humidity 5 to 100 % RH
IP rating IP65 / IP67
(see individual specifications for details)
Shock
Shock: SIST EN 60068-2-27:2009
100 g, 6 ms, half-sine
100x pos./neg in each axis
600x total
Vibration
Random vibration: MIL-STD-202G Method 214A, test condition II-D
Profile break points:
50 Hz @ 0.025 g²/Hz
100 Hz @ 0.1 g²/Hz
2000 Hz @ 0.1 g²/Hz
Profile RMS / Peak = 13.9 g / 41.7 g
8 hrs in each axis, 24 hrs total
Rev: 1557765000
1xAO
 
1xAO
4xDI
4xDO
1xACC
1xSTG
1xLV-BNC
1xHV
1xTH-HV
1xCNT
Analog Output
Output types Voltage
Number of channels 1
Output connector BNC
DAC Resolution 18 bit
Update Rate 1000 S/sec (see 1)
Full Scale Output Range ±10 V (see 2)
Accuracy (typ.) 0.1 % ±1 mV (0 to 20 mA load)
Temperature gain drift (typ.) ±10 ppm/K
Temperature offset drift (typ.) ±5 uV/K
SNR @ 1000 S/s output rate 92 dB (sine wave, 250 Hz, ±9 V)
THD -90 dB
Output impedance 0.45 Ω DC
Maximum output current 20 mA
Settling time (0.05 % of set value) 30 μs @ 1000 Ω load, -10 V to 10 V step
Max slew rate 2.5 V/μs @ 1000 Ω load
Max capacitive load (2 % overshoot) 10 nF
Maximum load 500 Ω
Output protection Short circuit protected
Isolation
Power
Power consumption 2 W (typ.)
Environmental
IP rating IP65 / IP67 (see 3)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
1) Only asynchronous mode is supported in Dewesoft, function generator is not supported
2) Only DC output voltage, function generator not supported
3) Depending on the mating connector types
Rev: 1578868200
Digital Inputs
Input type Digital
Number of channels 4
Connector DSUB15HD Male
Compatibility TTL / CMOS Voltage Levels
Input low level UIN < 1 V
Input high level UIN > 2 V
Input high current @ 5 V UIN 3 mA typ.
Input high current @ 30 V UIN 6 mA typ.
Propagation delay < 1 μs
Max. sampling rate 40 kS/sec
Overvoltage protection 30 V Continuous, 65 V peak
Isolation Galvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V 5 V +/- 10 %
300 mA max. (see 1)
Output Voltage +12 V 12 V +/-10 %
100 mA max. (see 1)
Output Voltage +Vecat EtherCAT Bus Supply Voltage
200 mA max. (see 1)
Power
Power consumption 1.5 W (typ.)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200
Digital Outputs
Output type Digital
Number of channels 4
Connector DSUB15HD Female
Maximum update rate depends on EtherCAT master cycle time
Output type open collector with active internal pullup to 5 V
Sink max 50 V, 2 A (resistive load, unprotected)
Source: 5 V, max. 40 mA (internally limited)
Max. switching frequency for internal PWM 100 kHz
Isolation Galvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V 5 V +/- 10 %
300 mA max. (see 1)
Output Voltage +12 V 12 V +/-10 %
100 mA max. (see 1)
Output Voltage +Vecat EtherCAT Bus Supply Voltage
200 mA max. (see 1)
Power
Power consumption 2 W (typ.)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200
Analog inputs
Input types Voltage, IEPE
Number of channels 1
Input connector BNC
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate Simultaneous 40 kS/sec per channel (software-selectable)
Voltage Ranges ±10 V ±5 V ±1 V ±200 mV
Typ. Input Accuracy ±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz) 90 dB 90 dB 89 dB 88 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz) 113 dB 110 dB 109 dB 106 dB
Typ. Noise floor @ 10 kS/sec -100 dB -99 dB -99 dB -98 dB
Typical CMR @ 400 Hz / 1 kHz 130 dB / 120 dB 122 dB / 119 dB 104 dB / 97 dB 90 dB / 84 dB
Gain Drift typ. 10 ppm/K (max. 40 ppm/K)
Offset Drift typ. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity < 0.02 %
Input Coupling DC, AC 0.1 Hz, 1 Hz
Input Impedance 1 MΩ
Overvoltage Protection In+ to In-: 50 V continuous, 200 V peak (10 msec)
Isolation 125 Vrms channel to ground isolation
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
IEPE input
Excitation 4 mA, 8 mA
Compliance voltage 24 V
Output Impedance
Sensor detection Shortcut: <4 V; Open: >19 V
TEDS support IEPE mode only
Power
Power consumption 2 W (typ.)
Environmental
IP rating IP65 / IP67 (see 1)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
1) Depending on the mating connector types
Rev: 1578868200
Analog input - Voltage
Input types Voltage, current, full bridge strain, half bridge strain, quarter bridge strain
Number of channels 1
Input connector DB9
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate Simultaneous 40 kS/sec per channel (software-selectable)
Voltage Ranges ±50 V ±10 V ±1 V ±100 mV
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/sec 89 dB 88 dB 88 dB 87 dB
Typical Dynamic Range @ 10 kS/sec -100 dB -110 dB -130 dB -145 dB
Typical Noise floor @ 10 kS/sec -103 dB -99 dB -103 dB -96 dB
Typical CMR @ 400 Hz / 1 kHz 71 dB / 66 dB 72 dB / 66 dB 96 dB / 88 dB 96 dB / 87 dB
Gain Drift Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity < 0.02 %
Input Coupling DC, AC 1 Hz
Input Impedance 1 MΩ 20 MΩ
Overvoltage Protection 200 V 50 V
Isolation 125 Vrms channel to ground isolation
TEDS support Standard + DSI adapters
Analog inputs - Current
Current ranges 20 mA 2 mA
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor 50 Ω
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Excitation Voltage
Excitation voltage Free programmable (16-bit DAC)
Predefined Levels Unipolar 0 - 24 V, Bipolar 0 - 12 V
Accuracy ±0.05 % ±2 mV
Drift ±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load < 0.01 %
Current Limit 42 mA (400 mW max. Power)
Protection Continuous short to ground
Bridge Connection Types full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Bridge ranges 20…10000 mV/V free programmable
Internal Bridge Completion ½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy 0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor 100 kΩ (others on request)
Shunt Resistor Accuracy 0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust Software-selectable
Power
Power consumption 2.8 W (typ.)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
Rev: 1591983000
Analog input
Input types Voltage
Number of channels 1
Input connector BNC
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate Simultaneous 40 kS/sec per channel (software-selectable)
Voltage Ranges ±50 V ±10 V ±1 V ±100 mV
Input Accuracy ±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/s 96 dB 96 dB 94 dB 88 dB
Typical Dynamic Range @ 10 kS -130 dB -132 dB -137 dB -138 dB
Typical Noise floor @ 10 kS -108.3 dB -102.6 dB -107.2 dB -100.1 dB
Gain Drift Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity < 0.02 %
Input Coupling DC, AC 1 Hz
Input Impedance 1 MΩ 20 MΩ
Overvoltage Protection 200 V 50 V
Isolation 125 Vrms channel to ground isolation
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Power
Power consumption 1.5 W (typ.)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
Rev: 1578868200
Analog Input
Input types Voltage
Number of channels 1
Input connector 4 mm safety banana jack
ADC Type 24-bit SAR with anti-aliasing filter
Sampling Rate 40 kS/sec (software-selectable)
Input range ±1000 V
Input accuracy ±0.03 % of reading ±0.2 V
Typ. Noise floor @ 10 kS/sec -96 dB
Typ. Noise floor @ 40 kS/sec -90 dB
Typ. CMR @ 400 Hz / 1 kHz
Gain Drift
Offset Drift
Gain Linearity
Input Coupling DC
Input Impedance 10 MΩ
Protection class CAT III 600 V, CAT II 1000 V
Overvoltage Protection +-2 kVpeak
Analog input performance
Bandwidth (-3 dB) 0.49 fs
Alias-free Bandwidth DC to 0.453 fs
Alias Rejection -100 dB (all sample rates)
Delay Through ADC 37 / fs
Oversampling 32
Power
Power consumption 1 W (typ.)
Environmental
IP rating IP65 / IP67 (see 1)
Physical
Dimensions 62 x 56 x 36 mm
Weight 300 g
1) Depending on the mating connector types
Rev: 1578868200
Inputs
Input types Thermocouple
Number of channels 1
Input connector K-type Thermocouple LEMO REDEL 2P series
ADC Type 24-bit delta-sigma
Sampling Rate Simultaneous 100 S/sec
Isolation voltage CAT III 600 V, CAT II 1000 V
Input Impedance 100 MΩ
Thermocouple
TC type Type K
Accuracy ±0.02 % of reading ±0.5 °C ±10 μV
Resolution < 0.001 °C
Sampling rates 100, 80, 40, 20, 10 S/sec
Typical Noise 0.007°C RMS @ Type K @ 10 S/sec
Power
Power consumption 1.3 W (typ.)
Physical
Dimensions 62 x 56 x 36 mm
Weight 300 g
Rev: 1578868200
Counter
Input type Digital
Number of channels 1
Input connector LEMO 1T series 7-pin
Timebase 100 MHz
Time base accuracy Typical: 5 ppm, Max: 20 ppm
Max. bandwidth 10 MHz
Input Filter 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level Compatibility TTL (Low: < 0.8 V, High > 2 V)
Input impedance 100 kΩ pull-up to +3.3 V
Input Protection ±25 V continuous
Sensor supply 5 V / 100 mA, 12 V / 90 mA
Isolation
Non-Isolated Sensor Power Supply
Output Voltage +5 V 5 V +/- 10 %
100 mA max.
Output Voltage +12 V 12 V +/-10 %
90 mA max.
Power
Power consumption 1.2 W (typ.)
Physical
Dimensions 62 x 56 x 29 mm
Weight 250 g
Rev: 1578868200