Tech specs - IOLITE
IOLITEr
IOLITEr
IOLITEs








Technical specifications
System specifications
System | IOLITEr | IOLITEs |
Number of slots | 12 | 8 |
Synchronization | 2x SIRIUS® SYNC on L00B4f | 2x SIRIUS® SYNC on L00B4f |
Sync Accuracy | below 1 sample to Sirius® | below 1 sample to Sirius® |
Dual EtherCAT® interface | ||
Number of buses | Two (both with buffered DAQ or real time) | Two (both with buffered DAQ or real time) |
Data Rate | Dual 100 Mbit bus speed | Dual 100 Mbit bus speed |
Max. Throughput per bus | 3 MS/s | 3 MS/s |
Bus 1 connectors | 2x Ethernet RJ45 | 2x Lemo 1T |
Bus 2 connectors | 2x Ethernet RJ45 | 2x Ethernet RJ45 |
Minimum delay (analog input to EtherCAT® bus) |
70 µs | 70 µs |
Minimum EtherCAT® cycle time | 100 µs | 100 µs |
Power | ||
Power supply | Dual redundant 12 - 48 V DC | Dual redundant 12 - 48 V DC |
Power consumption | 9 W to 11 W (incl. IOLITE-GATE) IOLITE-GATE: Max. 1.9 W |
8 W (Max: 9 W) |
Environmental | ||
Operating Temperature | -10 to 50 °C | -10 to 50 °C |
Storage Temperature | -40 to 85 °C | -40 to 85 °C |
Humidity | 5 to 95 % RH non-condensing at 50 °C | 5 to 95 % RH non-condensing at 50 °C |
IP rating | IP30 | IP40 |
Physical | ||
Dimensions | 483 x 148 x 133 mm | 266 x 169 x 139 mm |
Weight | 3.1 kg (incl. IOLITE-GATE) 230 g (IOLITE-GATE) |
2.6 kg |
Rev: 1576072800 |
Amplifier overview
6xSTG | 8xTH | 32xDI | 32xDO | 8xRTD | 8xLV | |
Connectors | DB9 | Thermocouple | Terminal block | Terminal block | L0B6f | BNC, Terminal block |
#ch per module | 6x | 8x | 32x | 32x | 8x | 8x |
Data rate / channel | 20 kS/sec | 100 S/sec | 40 kS/sec | 100 S/sec | 20 kS/sec | |
Resolution | 24-bit | 24-bit | digital | digital | 24-bit | 24-bit |
Bandwidth | 0.49*fs | 0.49*fs | ||||
Voltage ranges | ±50 V, ±10 V, ±1 V, ±100 mV | ±1 V, ±100 mV | open collector | ±1 V, ±100 mV | ±100 V, ±10 V (±10 V, ±1V on request) |
|
Input coupling | DC, AC 1 Hz | DC | DC | DC | ||
Sensor excitation | 0..12 V (bipolar), 0..24 V (unipolar) max. 0.4 W/ch | |||||
Bridge connection | Full, ½, ¼ 350 Ω, ¼ 120 Ω 3-wire | |||||
Programmable shunt | 100 kΩ | |||||
IEPE input | DSI-ACC | |||||
Current | 20 mA (internal shunt), DSI-5A | |||||
Temperature (PTx) | DSI-RTD | PT100, 200, 500, 1000, 2000 | ||||
Thermocouple | DSI-TH | K, J, T, R, S, N, E, C, U, B | ||||
Resistance | 1 kΩ, 10 kΩ | |||||
Potentiometer | ||||||
LVDT | DSI-LVDT | |||||
Charge | DSI-CHG | |||||
TEDS | ||||||
Isolation voltage | Differential | 1000 V | 1000 V | 1000 V | 1000 V | 1000 V |
Power consumption per module | Typ. 5.4 W, Max. 11.1 W |
3.2 W | Typ. 1.2 W, Max. 1.9 W |
Typ. 1.2 W, Max. 2.0 W |
Typ. 2.1 W, Max. 2.7 W |
Typ. 2.4 W, Max. 3.5 W |
Advanced functions | Supports all strain types and high input range | High voltage, high isolation | watchdog | High voltage, high isolation | High voltage, high isolation | |
Rev: 1575630000 |
6xSTG
6xSTG
8xTH
8xRTD
32xDI
32xDO
Analog inputs - Voltage | ||||
Input type | Voltage Full/half/quarter bridge strain Current Potentiometer |
|||
Number of channels | 6 | |||
ADC Type | 24-bit SAR with anti-aliasing filter | |||
Sampling Rate | Simultaneous 20 kS/sec per channel (software-selectable) | |||
Voltage Ranges | ±50 V | ±10 V | ±1 V | ±100 mV |
Input Accuracy | ±0.03 % of reading, ±0.02 % of range, ±0.1 mV | |||
Typical Dynamic Range @10 kS | 100 dB | 110 dB | 130 dB | 145 dB |
Typical Noise floor @10 kS | 103 dB | 97 dB | 103 dB | 94 dB |
Typical CMR @400 Hz / 1 kHz | -71 dB / -66 dB | -72 dB / -66 dB | -96 dB / -88 dB | -96 dB / -87 dB |
Gain Drift | Typical 10 ppm/K (max. 40 ppm/K) | |||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | < 0.02% | |||
Input Coupling | DC, AC 1Hz | |||
Input Impedance | 1 MΩ | 1 MΩ | 20 MΩ | 20 MΩ |
Overvoltage Protection | In+ to In-: 50 V continuous, 200 V peak (10 msec) | |||
Analog inputs - Current | ||||
Current ranges | 20 mA | 2 mA | ||
Input Accuracy | ±0.03 % of reading, ±0.02 % of range, ±2.1 μA | |||
Internal Shunt Resistor | 50 Ω | |||
Analog input performance | ||||
Bandwidth (-3 dB) | 0.49*fs | |||
Alias-free Bandwidth | DC to 0.453*fs | |||
Alias Rejection | -100 dB (all sample rates) | |||
Delay Through ADC | 37 / fs | |||
Oversampling | 32 | |||
Excitation Voltage | ||||
Excitation Voltage | Free programmable (16-bit DAC) | |||
Predefined Levels | Bipolar: 0, 1, 2, 5, 10 and 12 VDC Unipolar: 0, 2, 5, 10, 15, 24 VDC |
|||
Accuracy | ±0.05 % ±2 mV | |||
Drift | ±50 ppm/K ±100 μV/K | |||
Stability 10 % to 90 % Load | < 0.01 % | |||
Current Limit | 42 mA (550 mW max. power) | |||
Protection | Continuous short to ground | |||
Excitation Current | ||||
Excitation Voltage | Free programmable (16-bit DAC) | |||
Predefined Levels | 0, 2, 4, 8, 16, 44 mA | |||
Accuracy | ±0.1 % ±2 μA (<10 mA), ±0.5 % ±5 μA (>10 mA) | |||
Bridge measurement | ||||
Bridge Connection Types | full bridge strain, ½ bridge strain, ¼ bridge strain (3-wire) | |||
Ranges | 2…1000 mV/V free programmable | |||
Internal Bridge Completion | ½ bridge and ¼ bridge 120 and 350 Ω | |||
Bridge Completion Accuracy | 0.05 %; TCR: 5 ppm/K (others on request) | |||
Internal Shunt Resistor | 100 kΩ (others on request) | |||
Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | |||
Input Short, Sensor Offset Adjust | Software-selectable | |||
Additional Specifications | ||||
Input connectors | DB9 | |||
TEDS support | Standard + DSI adapters | |||
Power supply | 12 - 48 V DC | |||
Power Consumption | 5.4 W, Max. 11.1 W (7.9 W 120 Ω @ 5 V load, 8.8 W 350 Ω @ 10 V load) | |||
Weight | 340 g | |||
Slice Dimensions | 128.4 x 115.4 x 30.1 mm | |||
Rev: 1568613600 |
Inputs | ||
Input type | Isolated universal thermocouple and voltage | |
Number of channels | 8 | |
ADC Type | 24-bit delta-sigma | |
Sampling Rate | Simultaneous 100 S/sec | |
Voltage Ranges | ±1 V | ±100 mV |
Input Accuracy | ±0.02 % of reading ±10 μV | ±0.02 % of reading ±10 μV |
Typical Noise floor @10/100 s/sec | 115 dB / 106 dB | 110 dB / 106 dB |
Gain Drift | Typical 4 ppm/K (max. 10 ppm/K) | |
Offset Drift | Typical 0.05 μV/K (max. 0.2 μV/K) | |
Gain Linearity | <0.01% | |
Input Coupling | DC | |
Input Impedance | 100 MΩ | |
Thermocouple | TC Types: K, J, T, R, S, N, E, C, B | |
Accuracy | ±0.02 % of reading ±0.5 °C ±10 μV | |
Resolution | < 0.001 °C | |
Sampling rates | 10, 20, 40, 80, 100 S/sec | |
Typical Noise | 0.007 °C [email protected] K @ 10 S/sec 0.02 °C [email protected] K @ 100 S/sec |
|
Additional Specifications | ||
Input connectors | Mini Thermocouple connector (copper) | |
Isolation voltage | 1000 Vpeak channel to ground & channel to channel | |
Power supply | 12 - 48 V DC | |
Power consumption | 3.2 W | |
Weight | 230 g | |
Slice Dimensions | 128.4 x 115.4 x 30.1 mm | |
Rev: 1568305200 |
Analog inputs | ||
Input types | voltage, resistor or universal PTxxx inputs | |
Number of channels | 8 | |
ADC Type | 24-bit delta-sigma | |
Sampling Rate | Simultaneous 100 S/sec | |
Voltage Ranges | ±1 V | ±100 mV |
Input Accuracy | ±0.02 % of reading ±0.01 % of range ±10 μV |
±0.02 % of reading ±0.01 % of range ±10 μV |
Typical Noise floor @10/100 s/sec |
117 dB / 107 dB | 111 dB / 101 dB |
Gain Drift | Typical 4 ppm/K (max. 10 ppm/K) | |
Offset Drift | Typical 0.05 μV/K (max. 0.2 μV/K) | |
Gain Linearity | < 0.01 % | |
Input Coupling | DC | |
Input Impedance | 1 MΩ | |
Temperature | PT500, PT1000, PT2000 | PT100, PT200 |
Measurement range | -200 °C to +850 °C | |
Accuracy | ±0.05 % of reading ±0.2 °C | |
Temperature Drift | typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K) | |
Input Connection | 3-wire or 4-wire | |
Resolution | < 0.001 °C | |
Resistance | 0…10 kΩ | 0…1 kΩ |
Accuracy | ±0.02 % of reading ±0.01 % of range | |
Input Connection | 3-wire or 4-wire | |
Additional Specifications | ||
Input connectors | Lemo 0B 6pin EEA.0B.306.CLN | |
Isolation voltage | 1000 Vpeak channel to ground & channel to channel | |
Power supply | 12 - 48 V DC | |
Power consumption | Typ. 2.1 W, Max. 2.7 W | |
Weight | 260 g | |
Dimensions | 128.4 x 115.4 x 30.1 mm | |
Rev: 1568244600 |
Digital Input | |
Isolated Input Channels | 32 |
Input low level | -1 V ~ +1 V |
Input high level | -48 V ~ -3 V, +3 V ~ +48 V |
Input high current @5 V | UIN < 1 mA |
Input high current @30 V | UIN < 1 mA |
Sampling rate | Simultaneous 40 kS/sec |
Overvoltage protection | 100 V continuous (250 Vpeak) |
Isolation voltage peak | 1000 V channel to ground & channel to channel |
Additional Specifications | |
Input connectors | Terminal block, 2 pole, 4 x 9 pole OMNIMATE SL 2.50 / BLF 2.50/180 |
Power supply | 12 - 48 V DC |
Power consumption | Typ. 1.2 W, Max. 1.9 W |
Weight | 220 g |
Slice Dimensions | 128.4 x 115.4 x 30.1 mm |
Rev: 1566554400 |
Digital Output | |
Isolated Output Channels | 32 |
Compatibility | Solid state relay |
Maximum sink current | 0.5 A |
Maximum switching voltage | 50 V |
Maximum update rate | depending on EtherCAT master |
Isolation voltage peak | 1000 V channel to ground, no channel to channel isolation |
Additional Specifications | |
Input connectors | Terminal block, 2 pole, 4 x 9 pole OMNIMATE SL 2.50 / BLF 2.50/180 |
Power supply | 12 - 48 V DC |
Power consumption | Typ. 1.2 W, Max. 2.0 W |
Weight | 230 g |
Slice Dimensions | 128.4 x 115.4 x 30.1 mm |
Rev: 1566554400 |