Specifiche tecniche di SIRIUS® XHS
- Specifiche del sistema SIRIUS® XHS
- Specifiche del SIRIUS® XHS HybridADC
- Specifiche di filtraggio SIRIUS® XHS HybridADC
- Specifiche dei contatori digitali SIRIUS® XHS
- Panoramica degli amplificatori SIRIUS® XHS
- Specifiche dell'amplificatore SIRIUS® XHS ACC
- Specifiche dell'amplificatore SIRIUS® XHS HV
- Specifiche dell'amplificatore SIRIUS® XHS LV
- Specifiche dell'amplificatore SIRIUS® XHS UNI
Specifiche del sistema SIRIUS® XHS
Power specs | |
---|---|
Power Supply | 9 - 48 V DC |
Power consumption | Typ. 30 W |
Environmental | |
Operating Temperature | -10 to 50 °C |
Storage Temperature | -40 to 85 °C |
Humidity | 5 to 95 % RH non condensing @ 60 °C |
IP rating | IP20 |
Shock & Vibration | Shock (EN 60068-2-27:2009) 75 g, 6 ms, half-sine (25x pos./neg in each axis) Random Vibration (EN 60721-3-2: 1997 - Class 2M2) Sweep sinus Vibration (EN 60068-2-6:2008) |
Dimensions | 266 mm x 149 mm x 55 mm 266 mm x 149 mm x 69 mm (extended slice) |
Interfaces | |
Ethernet | 1 GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45) |
USB | USB 3.0 (Type C) |
CAN | CAN 2.0, CAN-FD (DSUB9) |
Sync Input/Ouput | |
Level (Input/Output) | TTL compatible |
Max. Output Current | ±24 mA (±50 mA for 1 sec) |
Synchronization | |
Delay between slices | ± 1 μs ( to the reference clock ) |
Max. Sync-cable length | 100 m (Master/Slave), 200 m (IRIG) |
Specifiche del SIRIUS® XHS HybridADC
ADC | |
---|---|
Type | Hybrid ADC |
High bandwidth mode | 16 bit SAR, up to 15 MS/s |
Alias free mode | 24 bit Sigma Delta, up to 2 MS/s |
Digital low pass filter | Software selectable (off, alias free) |
Analog HW filter | Analog 1 MHz 6th order (Butterworth) |
Alias free filter | 0.5*fs cutoff, 0.45*fs pass band, 0.55*fs stop band to -100dB, zero phase distortion, available below 2MS/s |
Specifiche di filtraggio SIRIUS® XHS HybridADC
Filter Mode | High-bandwidth | 1 MHz LPF | High-dynamic |
---|---|---|---|
Max. SR | 15 MS/s | 15 MS/s | 2 MS/s |
SW settings | Off | 1 MHz | AAF |
Bandwidth (-3 dB) | 5 MHz | 1 MHz | 0.49 fs |
Passband frequency (-0.1 dB) | 500 kHz | 500 kHz | 0.45 fs |
Passband flatness | ± 0.1 dB | ± 0.1 dB | ± 0.1 dB |
Alias-free bandwidth | ✗ | 7.5 MHz | 0.45 fs |
HW filter | ✗ | ✓ | ✓ |
Stopband frequency | ✗ | 7.5 MHz | 0.55 fs |
Stopband attenuation | ✗ | -100 dB | -100 dB |
Specifiche dei contatori digitali SIRIUS® XHS
Counter Input | |
---|---|
Input Channels (See 1) | 8 |
Modes | Event counting, waveform timing, encoder, tacho, geartooth,... |
Counter timebase | 150 MHz |
Time base accuracy | Typical: 0.5 ppm, Max: 2 ppm |
Max. Bandwidth | 15 MHz |
Max. Sampling Rate | 5 MS/s |
Input Filter | Off, 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs |
Counter resolution | 32-bit |
Input Compatibility, Level | 3.3 V TTL/CMOS (Low: <0.8 V, High >2 V) |
Input termination, impedance | 100 kΩ pull-up to +3.3 V |
Input Protection | ±25 V continuous |
Digital Output | |
Output Channels | 8 connectors, 1 line per connector |
Output | 5 V digital output |
Maximum current | 32 mA |
Output series resistance | 50 Ω |
Sensor Power Supply | |
Output Voltage +5 V | 5 V +/- 10 % 500 mA typ. Output short protected (Shared between 8 ports) |
Output Voltage +12 V (See 2) | 12 V +/-10 % 300 mA typ. Output short protected (Shared between 8 ports) |
1) Digital inputs on Counter (individual A, B, Z input) can be used only for Trigger condition 2) Maximum 2x DS-TACHO4 laser probes supported. | |
Rev: 1702296000 |
Panoramica degli amplificatori SIRIUS® XHS
XHS-HV | XHS-LV | XHS-ACC | |
---|---|---|---|
Connectors | BANANA | DB9, BNC, BANANA | BNC |
Channels per slice | 8 | 8 | 8 |
Data rate / channel | 15 MS/s | 15 MS/s | 15 MS/s |
Resolution | 16-bit (24-bit @ 1 MS/s) | 16-bit (24-bit @ 1 MS/s) | 16-bit (24-bit @ 1 MS/s) |
Bandwidth | 5 MHz | 5 MHz | 5 MHz |
Voltage ranges | ±2000 V ... ±200 V | ±100 V ... ±50 mV | ±10 V ... ±200 mV |
Input coupling | DC | DC, AC 1 Hz | DC, AC 0.1 Hz, AC 1 Hz |
Sensor excitation | ✗ | 2.5..30 V bipolar, 2..24 V unipolar, max. 0.2 A / 2 W | IEPE 2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA |
Bridge connection | ✗ | ✗ | ✗ |
Programmable shunt | ✗ | ✗ | ✗ |
IEPE input | ✗ | DSI-ACC | ✓ |
Resistance | ✗ | ✗ | ✗ |
Temperature (PTx) | ✗ | DSI-RTD | ✗ |
Thermocouple | ✗ | DSI-TH | ✗ |
Potentiometer | ✗ | ✗ | ✗ |
LVDT | ✗ | DSI-LVDT | ✗ |
Charge | ✗ | DSI-CHG | ✗ |
Current | ✗ | ext. shunt DSI20mA, DSI5A | ext. shunt |
TEDS | ✗ | ✓ | ✓ |
Isolation voltage | CATII 1000 V | 420 Vdc (300 Vacrms) | 140 Vdc (100 Vacrms) |
Power consumption per channel (typ.) | 1.45 W/ch | 1.55 - 5 W/ch | 1.8 W/ch |
Advanced functions | High voltage, high bandwidth, high isolation | High sensor excitation and multi range | Sensor error detection, high speed |
Rev: 1701403200 |
Specifiche dell'amplificatore SIRIUS® XHS ACC
Inputs | |||||||
---|---|---|---|---|---|---|---|
Input types | Voltage, IEPE | ||||||
ADC Type | Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s | ||||||
Sampling Rate | Simultaneous 15 MS/s | ||||||
Filtering | AAF 1 MHz (6th order) | ||||||
Analog bandwidth (-3 dB) | 5 MHz | ||||||
Voltage Mode | |||||||
Ranges | ±10, 5, 2, 1, 0.4 and 0.2 V | ||||||
Input Accuracy | DC | ±0.03 % of reading ±0.02 % of range ±50 μV | |||||
Up to 1 kHz | ±0.04 % of reading ±0.02 % of range | ||||||
Up to 10 kHz | ±0.06 % of reading ±0.05 % of range | ||||||
Up to 100 kHz | ±0.1 % of reading ±0.1 % of range | ||||||
Up to 1000 kHz | ±5 % of reading ±0.5 % of range | ||||||
Noise floor, Typ. | Sample rate, filter \ Range → | 10 V | 5 V | 2 V | 1 V | 0.4 V | 0.2 V |
15 MS/s, Filter off | -85 dB | -84 dB | -83 dB | -82 dB | -77 dB | -72 dB | |
1 MS/s, Filter on | -98 dB | -98 dB | -97 dB | -95 dB | -92 dB | -87 dB | |
100 kS/s, Filter on | -109 dB | -107 dB | -108 dB | -107 dB | -103 dB | -98 dB | |
10 kS/s, Filter on | -119 dB | -119 dB | -119 dB | -118 dB | -114 dB | -109 dB | |
CMR, Typ. | Frequency \ Range → | 10 V | 5 V | 2 V | 1 V | 0.4 V | 0.2 V |
50 Hz | 141 dB | 141 dB | 139 dB | 133 dB | 121 dB | 120 dB | |
400 Hz | 130 dB | 133 dB | 136 dB | 137 dB | 137 dB | 131 dB | |
1 kHz | 122 dB | 125 dB | 127 dB | 129 dB | 130 dB | 131 dB | |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | ||||||
Offset Drift | Typical 0.5 μV/K + 1 ppm of range/K, max. 2 μV/K + 4 ppm of range/K | ||||||
Gain Linearity | < 0.02 % | ||||||
Inter Channel Phase-mismatch | 0.005° * fin [kHz] + 0.0002° | ||||||
Channel Cross talk | -145 dB typ. @ 1 kHz | ||||||
Input Coupling | DC or AC (1 Hz, 0.1 Hz) | ||||||
Input Impedance | 1 MΩ | ||||||
Overvoltage Protection | 50 V continuous; 200 V peak (10 msec) | ||||||
IEPE mode | |||||||
Excitation | 2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA | ||||||
Compliance voltage | 24 V | ||||||
Output Impedance | > 10 kΩ | ||||||
Sensor detection | Shortcut: < 4 V; Open: > 19 V | ||||||
Additional Specifications | |||||||
Input connector | BNC | ||||||
TEDS support | IEPE mode only | ||||||
Rev: 1623052800 |
Specifiche dell'amplificatore SIRIUS® XHS HV
Inputs | |||||
---|---|---|---|---|---|
ADC Type | Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s | ||||
Sampling Rate | Simultaneous 15 MS/s | ||||
Filtering | AAF 1 MHz (6th order) | ||||
Analog bandwidth (-3 dB) | 5 MHz | ||||
Voltage Mode | |||||
Ranges | ±2000 V, ±1000 V, ±400 V, ±200 V | ||||
Input Accuracy | Signal frequency | Accuracy | |||
DC to 1 kHz | ±0.03 % of reading ±0.02 % of range | ||||
Up to 10 kHz | ±0.1 % of reading ±0.05 % of range | ||||
Up to 100 kHz | ±4 % of reading ±0.1 % of range | ||||
Up to 1000 kHz | ±5 % of reading ±0.5 % of range | ||||
Noise floor, Typ. | Sample rate / Range → | 2000 V | 1000 V | 400 V | 200 V |
15 MS/s | -84 dB | -82 dB | -79 dB | -75 dB | |
1 MS/s | -95 dB | -93 dB | -85 dB | -78 dB | |
100 kS/s | -108 dB | -106 dB | -100 dB | -95 dB | |
10 kS/s | -117 dB | -115 dB | -109 dB | -104 dB | |
CMR, Typ. | 101 dB @ 50 Hz, 74 dB @ 400 Hz | ||||
Channel Crosstalk | -116 dB typ. @ 50 Hz, -89 dB typ. @ 1 kHz | ||||
Gain Drift | Typical 20 ppm/K, max. 40 ppm/K | ||||
Offset Drift | Typical 1.5 mV/K + 1 ppm of range/K, max 3 mV/K + 2 ppm of range/K | ||||
Gain Linearity | < 0.01 % | ||||
Input Coupling | DC | ||||
Input Impedance | 10 MΩ | 1 pF | ||||
Overvoltage category | CAT II 1000 V | ||||
Maximum input voltage | 2000 Vdc or 2000 Vpk (1414 Vacrms) | ||||
Additional Specifications | |||||
Input connector | Banana | ||||
Rev: 1698322800 |
Specifiche dell'amplificatore SIRIUS® XHS LV
Inputs | Voltage | ||||
---|---|---|---|---|---|
ADC Type | Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s | ||||
Sampling Rate | Simultaneous 15 MS/s | ||||
Filtering | AAF 1 MHz (6th order) | ||||
Analog bandwidth (-3 dB) | 5 MHz | ||||
Voltage Mode | |||||
Ranges | ±100, 50, 20, 10, 5, 2.5, 1, 0.5, 0.25, 0.1 and 0.05 V | ||||
Input Accuracy | DC | ±0.03 % of reading ±0.02 % of range ±100 μV (2 mV for Ranges ≥ 10 V) | |||
Up to 1 kHz | ±0.03 % of reading ±0.02 % of range | ||||
Up to 10 kHz | ±0.1 % of reading ±0.05 % of range | ||||
Up to 100 kHz | ±2 % of reading ±0.1 % of range | ||||
Up to 1000 kHz | ±5 % of reading ±0.5 % of range | ||||
Noise floor, Typ. | Sample rate, filter \ Range → | 100 V | 5 V | 0.5 V | 0.05 V |
15 MS/s, Filter off | -82 dB | -78 dB | -65 dB | -51 dB | |
1 MS/s, Filter on | -94 dB | -95 dB | -88 dB | -69 dB | |
100 kS/s, Filter on | -104 dB | -105 dB | -100 dB | -81 dB | |
10 kS/s, Filter on | -113 dB | -114 dB | -107 dB | -87 dB | |
CMR, Typ. | Frequency \ Range → | 100 V | 5 V | 0.5 V | 0.05 V |
50 Hz | 91 dB | 102 dB | 98 dB | 100 dB | |
400 Hz | 86 dB | 75 dB | 90 dB | 98 dB | |
10 kHz | 66 dB | 74 dB | 82 dB | 83 dB | |
Channel Crosstalk | Range ≥ 10 V: -105 dB @ 10 kHz Range < 10 V: -120 dB @ 10 kHz | ||||
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | ||||
Offset Drift | Range ≥ 10 V: Typ. 100 μV/K + 1 ppm of range/K, Max 250 μV/K + 2 ppm of range/K Range < 10 V: Typ. 4 μV/K + 1 ppm of range/K, Max 8 μV/K + 2 ppm of range/K | ||||
Gain Linearity | < 0.03 % | ||||
Input Coupling (see 1) | DC, AC 1 Hz | ||||
Input Impedance | Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ | 110 pF between INx to GND | ||||
Overvoltage Protection | Range ≥ 10 V: 300 V continuous Range < 10 V: 100 V (200 V peak for 10 msec) | ||||
Max. common mode voltage Isolation voltage | 420 Vdc (300 Vacrms) | ||||
Excitation Voltage | |||||
Polarity | Unipolar or Bipolar Software selectable (programmable 16-bit DAC) | ||||
Excitation Level | Unipolar 1 .. 24 V; Predefined levels: 1, 2, 2.5, 5, 10, 12, 15, 20 and 24 VDC | ||||
Excitation Level | Bipolar 2.5 .. 30 V; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC | ||||
Drift | ±10 ppm/K ±150 μV/K | ||||
Stability 10% to 90% load (bipolar) | < 0.01 % | ||||
Current limit | 200 mA (2 Watt max. per Channel, 12 Watt max. per Slice) | ||||
Additional Specifications | |||||
Input connector | DSUB 9, BNC, Banana (others on request) | ||||
TEDS support | Standard + DSI® adapters | ||||
Rev: 1701403200 | |||||
1) In- must be within ±10 V referred to GND (iso); for Ranges ≥ 10 V the DC value of In- is not rejected |
Specifiche dell'amplificatore SIRIUS® XHS UNI
Inputs | |||||
---|---|---|---|---|---|
Input types | Voltage Full / Half / Quarter bridge strain (120 Ω and 350 Ω) Potentiometer, RTD, Resistance Current (ext. Shunt) IEPE | ||||
ADC Type | Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s | ||||
Sampling Rate | Simultaneous 15 MS/s | ||||
Filtering | AAF 1MHz (6th order Butterworth) | ||||
Analog bandwidth | 5 MHz | ||||
Voltage Mode | |||||
Ranges | ±100, 50, 20, 10, 5, 2.5, 1, 0.5, 0.25, 0.1 and 0.05 V | ||||
Input Accuracy | Signal frequency | Accuracy | |||
DC | ±0.03 % of reading ±0.025 % of range ±40 μV (1 mV for Ranges ≥ 10 V) | ||||
Up to 1 kHz | ±0.03 % of reading ±0.02 % of range | ||||
Up to 10 kHz | ±0.1 % of reading ±0.05 % of range | ||||
Up to 100 kHz | ±2 % of reading ±0.1 % of range | ||||
Up to 1000 kHz | ±5 % of reading ±0.5 % of range | ||||
Typ. Noise floor | Sample rate, filter \ Range → | 100 V | 5 V | 0.5 V | 0.05 V |
15 MS/s, Filter off | -81 dB | -81 dB | -75 dB | -56 dB | |
1 MS/s, Filter on | -94 dB | -94 dB | -84 dB | -64 dB | |
100 kS/s, Filter on | -104 dB | -105 dB | -100 dB | -81 dB | |
10 kS/s, Filter on | -113 dB | -114 dB | -107 dB | -88 dB | |
Typical CMR | Frequency \ Range → | 100 V | 5 V | 0.5 V | 0.05 V |
50 Hz | 91 dB | 104 dB | 101 dB | 83 dB | |
400 Hz | 85 dB | 96 dB | 92 dB | 83 dB | |
10 kHz | 62 dB | 64 dB | 76 dB | 75 dB | |
Gain Drift | Typical 15 ppm/K, Max. 30 ppm/K | ||||
Offset Drift | Range < 10 V: Typ. 1 μV/K + 2 ppm of range/K, Max 4 μV/K + 8 ppm of range/K Range ≥ 10 V: Typ. 50 μV/K + 2 ppm of range/K, Max. 150 μV/K + 6 ppm of range/K | ||||
Gain Linearity | < 0.01 % | ||||
Inter channel phase mismatch | 0.01° * fin [kHz] + 0.0002° | ||||
Channel Cross talk | Range ≥ 10 V: -100 dB @ 10 kHz Range < 10 V: -140 dB @ 10 kHz | ||||
Input Coupling | DC AC 0.15 Hz for all ranges; (1 Hz, 3 Hz, 5 Hz, 10 Hz, 20 Hz per SW) | ||||
Input Impedance | Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ | 110 pF between INx to GND | ||||
Overvoltage Protection | Range ≥ 10 V: 300 V continuous Range < 10 V: 100 V (200 V peak for 10 msec) | ||||
Max. common mode voltage Isolation voltage | 420 Vdc (300 Vacrms) | ||||
Excitation Voltage | |||||
Polarity | Unipolar or Bipolar Software selectable (programmable 16-bit DAC) | ||||
Excitation Level | Unipolar and Bipolar 0.15 V .. 24 V; Predefined levels: 1, 2, 5, 10, 12, 15, 20 and 24 V | ||||
Accuracy | ±0.05 % ±2 mV | ||||
Load stability 0 % to 100 % load | < 0.01 % | ||||
Line regulation over 20 Ω of change | < 0.005 % @ 120 Ω load | ||||
Noise @ 10 Volt / 350 Ω | < 300 μVrms @ 10 kHz BW | ||||
Impedance Sense to Exc Sense to GND | 100 kΩ (0.5 Ohm with internal excitation sense) > 100 MΩ | ||||
Current limit | 100 mA (max. 800 mW) | ||||
Protection | Continuous short to ground | ||||
Excitation Current | |||||
Excitation Current | Free programmable (16-bit DAC) | ||||
Ranges | 100 µA - 1 mA | 1 mA - 20 mA | 20 mA - 100 mA | ||
Accuracy | ±0.2 % ±0.5 μA | ±0.15 % ±2 μA | ±0.01 % ±40 μA | ||
Output Impedance | > 1 MΩ | ||||
Bridge Connection Types | |||||
Bridge types | Full / Half / Quarter bridge (3-wire or 4-wire) / Quarter Constant Current (2-wire or 4-wire) | ||||
Ranges | 2 mV/V…1000 mV/V free programmable | ||||
Internal Bridge Completion | ½ bridge and ¼ bridge 120 Ω and 350 Ω | ||||
Bridge Completion Accuracy | 0.05 %; TCR: 2 ppm/K (others on request) | ||||
Internal Shunt Resistor | 59.88 kΩ and 175 kΩ, software selectable (others on request) | ||||
Typ. Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | ||||
Input Short, Sensor Offset Adjust | Software selectable | ||||
Lead-wire compensation | Automatic | ||||
IEPE mode | |||||
IEPE Current | Free programmable (16-bit DAC) | ||||
Predefined levels | 2, 4, 8, 12, 16 and 20 mA | ||||
Compliance voltage | 24 V | ||||
Output Impedance | > 1 MΩ | ||||
Sensor detection | Shortcut: < 4 V; Open: > 19 V | ||||
Additional Specifications | |||||
Input connector | DSUB-9 (others on request) | ||||
TEDS support | Class 1 (IEPE) and Class 2 | ||||
DSI® adapters support | Yes | ||||
Rev: 1712840653 |