Caratteristiche tecniche dei regolatori di corrente

Specifiche tecniche del trasduttore di corrente DC-CT-1000I

	DC-CT-1000I-S22DA
Type	Zero-Flux
Primary Current Range DC (max)	1000 A
Primary Current Range AC rms (max)	700 A
Conversion ratio	1:1680
Nominal Burden Resistance	1 Ω (max. 3 Ω)
Transformer/Gain Off-Center Error	10ppm (max. <30ppm)
Temperature influence (typ.)	3 ppm/K
Nominal secondary current	~595.2 mA @ 1000 A
Gain Linearity @1000 A range	Typ. 83 ppm (max. <100ppm)
Offset including hysteresis	Typ. 65 mA (max. 100 mA)
Bandwidth ( -3 dB) (typ.)	DC ... 500 kHz
Noise (ppm rms)	Min [mA]	Typ [mA]	Max [mA]
0 - 10000 Hz	0.4	0.6	1.3
0 - 100000 Hz	0.8	1.2	2
0 - 1000000 Hz	5.4	5.5	6.5
Platiše Flux Sensor Frequency (seen as ripple)	220 kHz
D-Class Switching Frequency (seen as ripple)	750 kHz
Other
Time to Out of Range Detection (Status Deasserted)	300 µs
Primary to Secondary Maximum Difference RTI	±1500 mA
Status Open Collector Max Current	Typ. 25 mA (Max. 50 mA)
Status Open Collector Max Voltage	Typ. 60 V (Min. -5 V, Max. 80 V)
Immunity to external magnetic field, 5 mT in any direction RTI	Typ. ±30 mA (Max. < 50 mA)
Induced RMS voltage on primary conductor at IP = 0	32 µV
Induced RMS voltage on primary conductor during Search	1223 µV
Power Supply
	Min	Typ	Max
Power Supply Voltage between pin 9 and 5	24 V	30 V	35 V
500 A Range Power Supply Voltage	12 V	30 V	35 V
Power Supply Max. In-rush/working current @ 30 V	< 0.5 A
Standby (Idle) Power Consumption	Typ. 0.56 W (Max. 0.7 W)
Power Consumption	3 W @IP = 500 A and Burden 3 Ω 6.6 W (max. 8 W) @IP = 1000 A and Burden 1 Ω 7.6 W (max. 9 W) @IP = 1000 A and Burden 3 Ω
Environmental
Operating temperature	-40 °C to +85 °C
Non-insulated wire Isolation CAT II / CAT III IEC 61010-1 standards, EN 50178 standards	1000 V CAT II 600 V CAT III
Insulated wire Isolation CAT II / CAT III IEC 61010-1 standards, EN 50178 standards	1000 V CAT II 1000 V CAT III
Clearance / Creepage	12 mm
Weight	500 g
Inner diameter	22 mm
Dimensions	77 x 57 x 46.7 mm
DEWESoft® Shunt	1 Ω
PWR-MCTS2 needed	Yes (±15 V)

Specifiche tecniche delle pinze amperometriche CA/CC a cancello di flusso

	DS-CLAMP-20DC		DS-CLAMP-200DC		DS-CLAMP-500DCS		DS-CLAMP-500DC		DS-CLAMP-1000DC
Type	Flux gate		Flux gate		Flux gate		Flux gate		Flux gate
Current Range	20 A DC or AC RMS		200 A DC or AC RMS		500 A DC or AC RMS		500 A DC or AC RMS		1000 A DC or AC RMS
Sensitivity	100 mV/A		10 mV/A		4 mV/A		4 mV/A		2 mV/A
Bandwidth	DC to 1 MHz		DC to 500 kHz		DC to 200 kHz		DC to 100 kHz		DC to 20 kHz
Bandwidth (upgraded after 2022)	DC to 2 MHz		DC to 700 kHz		DC to 500 kHz		DC to 200 kHz		DC to 100 kHz
TEDS	Fully supported		Fully supported		Fully supported		Fully supported		Fully supported
Conductor Position Sensitivity	max. ± 0.1 % of reading		max. ± 0.1 % of reading		max. ± 0.1 % of reading		max. ± 0.2 % of reading		max. ± 0.2 % of reading
Zero Offset (+25°C)	max. 10mA		max. ± 100 mA		max. ± 250 mA		max. ± 250 mA		max. ± 200 mA
Error due Earth Magnetic Field	max. ± 50 mA		max. ± 50 mA		max. ± 100 mA		max. ± 150 mA		max. ± 150 mA
Temp. Coefficient	± 0.01 %/°C		± 0.01 %/°C		± 0.01 %/°C		± 0.01 %/°C		± 0.01 %/°C
Accuracy
Frequency	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error
DC	± 0.2 % rdg. ± 10 mA	-	± 0.2 % rdg. ± 40 mA	-	± 0.3 % rdg. ± 100 mA	-	± 0.2 % rdg. ± 100 mA	-	± 0.2 % rdg. ± 200 mA	-
to 100 Hz	± 0.2 % rdg. ± 2 mA	± 0.1 °	± 0.2 % rdg. ± 20 mA	± 0.1 °	± 0.3 % rdg. ± 50 mA	± 0.1 °	± 0.2 % rdg. ± 50 mA	± 0.1 °	± 0.2 % rdg. ± 100 mA	± 0.1 °
100 - 500 Hz	± 0.3 % rdg. ± 4 mA	± 0.2 °	± 0.3 % rdg. ± 40 mA	± 0.2 °	± 0.3 % rdg. ± 100 mA	± 0.2 °	± 0.3 % rdg. ± 100 mA	± 0.2 °	± 0.5 % rdg. ± 200 mA	± 0.2 °
500 Hz - 1 kHz	± 0.5 % rdg. ± 4 mA	± 0.5 °	± 0.5 % rdg. ± 40 mA	± 0.5 °	± 0.5 % rdg. ± 100 mA	± 0.5 °	± 0.5 % rdg. ± 100 mA	± 0.5 °	± 1.0 % rdg. ± 200 mA	± 0.5 °
1 kHz - 5 kHz	± 1.0 % rdg. ± 4 mA	± 1.0 °	± 1.0 % rdg. ± 40 mA	± 1.0 °	± 1.0 % rdg. ± 100 mA	± 1.0 °	± 1.0 % rdg. ± 100 mA	± (0.5 f [kHz]) °	± 2.0 % rdg. ± 200 mA	± (0.7 f [kHz]) °
5 kHz - 10 kHz	± 1.5 % rdg. ± 4 mA	± 1.5 °	± 1.5 % rdg. ± 40 mA	± 1.5 °	± 1.5 % rdg. ± 100 mA	± 1.5 °	± 1.5 % rdg. ± 100 mA	± (0.5 f [kHz]) °	± 5.0 % rdg. ± 200 mA	± (0.7 f [kHz]) °
10 kHz - 20 kHz	± 2 % rdg. ± 4 mA	± (0.5 + 0.1 f [kHz]) °	± 5 % rdg. ± 40 mA	± (0.5 + 0.1 f [kHz]) °	± 5 % rdg. ± 100 mA	± (0.15 f [kHz]) °	± 5 % rdg. ± 100 mA	± (0.5 f [kHz]) °	± 30 % rdg. ± 200 mA	± (0.7 f [kHz]) °
20 kHz - 50 kHz	± 2 % rdg. ± 4 mA	± (0.5 + 0.1 f [kHz]) °	± 5 % rdg. ± 40 mA	± (0.5 + 0.1 f [kHz]) °	± 5 % rdg. ± 100 mA	± (0.15 f [kHz]) °	± 10 % rdg. ± 250 mA	± (0.5 f [kHz]) °	± 30 % rdg. ± 200 mA	± (0.7 f [kHz]) °
50 kHz - 100 kHz	± 5 % rdg. ± 10 mA	± (0.5 + 0.1 f [kHz]) °	± 10 % rdg. ± 100 mA	± (0.5 + 0.1 f [kHz]) °	± 15 % rdg. ± 250 mA	± (0.15 f [kHz]) °	± 30 % rdg. ± 250 mA	± (0.5 f [kHz]) °	-	-
100 kHz - 200 kHz	± 10 % rdg. ± 10 mA	± (0.5 + 0.1 f [kHz]) °	± 15 % rdg. ± 40 mA	± (0.5 + 0.1 f [kHz]) °	± 30 % rdg. ± 250 mA	± (0.15 f [kHz]) °	-	-	-	-
200 kHz - 300 kHz	± 10 % rdg. ± 10 mA	± (0.5 + 0.1 f [kHz]) °	± 15 % rdg. ± 40 mA	± (0.5 + 0.1 f [kHz]) °	± 30 % rdg. ± 250 mA	± (0.15 f [kHz]) °	-	-	-	-
300 kHz - 500 kHz	± 15 % rdg. ± 10 mA	± (0.5 + 0.1 f [kHz]) °	± 30 % rdg. ± 100 mA	± (0.5 + 0.1 f [kHz]) °	-	-	-	-	-	-
500 kHz - 1 MHz	± 30 % rdg. ± 10 mA	± (0.5 + 0.1 f [kHz]) °	-	-	-	-	-	-	-	-
General Specifications
Dimensions [mm]	153 x 67 x 25		153 x 67 x 25		153 x 67 x 25		238 x 116 x 35		238 x 116 x 35
Max. Conductor Size	20 mm		20 mm		20 mm		50 mm		50 mm
Power Supply	± 11 V to ± 15 V		± 11 V to ± 15 V		± 11 V to ± 15 V		± 11.5 V to ± 15 V		± 11.5 V to ± 15 V
Current Consumption	max. 5 VA		max. 6 VA		max. 7 VA		max. 7 VA		max. 7 VA
Operating Environment	Indoors, Pollution Degree II, altitude up to 2000m		Indoors, Pollution Degree II, altitude up to 2000m		Indoors, Pollution Degree II, altitude up to 2000m		Indoors, Pollution Degree II, altitude up to 2000m		Indoors, Pollution Degree II, altitude up to 2000m
Operating Temp.	- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C
Operating Humidity	up to 80 % (not condensing)		up to 80 % (not condensing)		up to 80 % (not condensing)		up to 80 % (not condensing)		up to 80 % (not condensing)
Safety Standards	EN61010		EN61010		EN61010		EN61010		EN61010
EMC Standards	EN61326		EN61326		EN61326		EN61326		EN61326
Rohs	-		-		-		-		-
PWR-MCTS2 needed	Yes		Yes		Yes		Yes		Yes
Compatible amplifiers (see 1)	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43
Cable length	3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS		3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS		3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS		3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS		3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS
Data Sheet	DS-CLAMP-20DC		DS-CLAMP-200DC		DS-CLAMP-500DCS		DS-CLAMP-500DC		DS-CLAMP-1000DC
1) The ranges of the IOLITE and KRYPTON amplifiers might affect the resolution of the measured values.
NOTE: The specifications in the table above are refering to the latest HIOKI current clamp models

Specifiche tecniche delle pinze amperometriche CA/CC a effetto Hall

	DS-CLAMP-30DC	DS-CLAMP-150DC	DS-CLAMP-150DCS	DS-CLAMP-300DC	DS-CLAMP-1800DC
Type	Hall Effect	Hall Effect	Hall Effect	Hall Effect	Hall Effect
Current Range	30 A DC or AC peak	200 A DC or 150 A AC RMS	250 A DC or 150 A AC RMS	300 A DC or AC RMS	1800 A DC or AC RMS
Sensitivity	100 mV/A	20 mV/A	10 mV/A	1 mV/A	1 mV/A
Accuracy (+25°C)	± 1 % of reading ± 2 mA	1 % + 2 mA	1 % + 2 mA	± 1 % of reading ± 100 mA	0 - 1000 A: ± 2.5 % of reading ± 0.5 A 1000 - 1500 A: ± 3.5 % of reading 1500 - 1800 A: ± 5 % of reading
Bandwidth	DC to 20 kHz	DC to 100 kHz	DC to 100 kHz	DC to 20 kHz	DC to 20 kHz
Resolution	± 1 mA	± 1 mA	± 1 mA	± 100 mA	± 1 mA
TEDS	Fully supported	Fully supported	Fully supported	Fully supported	Fully supported
Conductor Position Sensitivity	-	± 0.5 %	± 1 %	± 1.5 % relative to center reading	± 1.5 %
Zero Offset (+25°C)	± 50 mV max.	± 10 mV max. + 1 mV/°C	± 10 mV max. + 0.1 mV/°C	± 10 mV max.	-
Error due Earth Magnetic Field	-	± 0.5 mV	±0.5 mV	max. 1A	max. 150 mA
Temp. Coefficient	± 0.01 % of reading / °C	± 0.02 % of reading / °C	± 0.02 % of reading / °C	± 0.1 % of reading / °C	± 0.15 % of reading / °C
Zero	External zero correction	Auto zero @ power supply of sensor	Auto zero @ power supply of sensor	External zero correction	Auto zero via push-button
General Specifications
Dimensions [mm]	200 x 55 x 15	205 x 60 x 15	106 x 100 x 25	192.60 x 55.30 x 15	205 x 60 x 15
Max. Conductor Size	32 mm	32 mm	25 mm	25 mm	32 mm
Power Supply	+ 12 V	± 10 V	± 10 V	+ 12 V ± 3 V	+ 9 V
Current Consumption	30 mA + 1 mA/A measured	30 mA + 1mA/A measured	30 mA + 1mA/A measured	max. 30 mA	max. 25 mA
Jaws Open Indication	No	Yes	No	No	No
Operating Temp.	0 to + 50 °C	0 to + 60 °C	0 to + 60 °C	0 to + 50 °C	0 to + 50 °C
Operating Humidity	-	15 % to 85 % (not condensing)	15 % to 85 % (not condensing)	-	15 % to 85 % (not condensing)
Safety Standards	EN 61010-1 EN 61010-2-032	EN 61010-1:2010 EN 61010-2-032:2012 EN 61010-2-031:2012	EN 61010-1:2010 EN 61010-2-032:2012 EN 61010-2-031:2012	EN 61010-1 EN 61010-2-032	EN 61010-1:2010 EN 61010-2-032:2012 EN 61010-2-031:2012
Safety	300 Vrms CAT I	300 Vrms CAT III	300 Vrms CAT III	300 Vrms CAT III	300 Vrms CAT III
EMC Standards	EN 61326-2-2	EN 61326-2-2:2013	EN 61326-2-2:2013	EN 61326-2-2	EN 61326-2-2:2013
PWR-MCTS2 needed	No	No	No	No	No
Compatible Amplifiers	SIRIUS LV / HS-LV / XHS-LV IOLITE LVe (see 1)	SIRIUS LV / HS-LV (see 1)	SIRIUS LV / HS-LV (see 1)	SIRIUS LV / HS-LV / XHS-LV IOLITE LVe (see 1)	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, KRYPTON STG IOLITE LVe DEWE-43
Cable length	2 m	3 m	3 m	3 m	3 m
Data Sheet	DS-CLAMP-30DC			DS-CLAMP-300DC	DS-CLAMP-1800DC
1) *in-rush current is too high, so the clamps are not compatible with other amplifiers

Specifiche tecniche delle pinze amperometriche CA

	DS-CLAMP-5AC	DS-CLAMP-15AC	DS-CLAMP-200AC	DS-CLAMP-1000AC
Type	Iron-Core	Iron-Core	Iron-Core	Iron-Core
Range	5 A AC RMS	15 A AC RMS	200 A AC RMS	1000 A AC RMS
Sensitivity	100 mV/A	100 mV/A	10 mV/A	1 mV/A
Accuracy (+25 °C)	5 mA - 0.5 A ± 2 % of reading 0.5 A - 1 A ± 1 % of reading 1 A - 12 A ±0 .5 % of reading	< 1 A ± 2.5 % of reading 1 A - 15 A ± 1 % of reading	0.5 A - 10 A ± 3.5 % of reading 10 A - 100 A ± 2.5 % of reading 100 A - 240 A ± 1 % of reading	< 1 A ± 2 % of reading 10 A - 100 A ± 0.5 % of reading 100 A - 1200 A ± 0.3 % of reading
Phase Error	5 mA - 0.5 A ± 2 ° 0.5 A - 1 A ± 1° 1 A - 12 A ± 1 °	< 1 A ± 5 ° 1 A - 15 A ± 3 °	0.5 A - 10 A not specified 10 A - 100 A ≤ 5 ° 100 A - 240 A ≤ 2.5 °	< 1 A not specified 10 A - 100 A ≤ 1 ° 100 A - 1200 A ≤ 0.7 °
Bandwidth	2 Hz to 5 kHz	2 Hz to 10 kHz	2 Hz to 10 kHz	2 Hz to 10 kHz
Resolution	0.01 A	0.01 A	0.5 A	0.001 A
TEDS	Fully supported	Fully supported	Fully supported	Fully supported
Overload Capability	1.5 x I nominal	1.3 x I nominal	1.3 x I nominal	1.3 x I nominal
Conductor Position Sensitivity	≤ 0.5 % of reading	≤ 0.5 % of reading	≤ 0.5 % of reading	≤ 0.1 % of reading
Influence of Crest Factor	≤ 1 %	≤ 3 %	≤ 3 %	≤ 1 %
Error due Earth Magnetic Field	/	≤ 15 mV/A @ 50 Hz	≤ 15 mV/A @ 50 Hz	≤ 15 µV/A @ 50 Hz
Temperature Coefficient	±0.015 % / °C	≤ 0.2 % / 10 °C	≤ 0.2 % / 10 °C	≤ 0.1 % / 10 °C
Influence of Frequency	/	< 5 % of output signal from 20 Hz ... 1 kHz < 10 % of output signal from 1 kHz ... 10 kHz	< 3 % of output signal from 20 Hz ... 1 kHz < 12 % of output signal from 1 kHz ... 10 kHz	< 1 % of output signal from 30 Hz ... 48 Hz < 0.5 % of output signal from 35 Hz ... 1 kHz < 1 % of output signal from 1 kHz ... 5 kHz
General Specifications
Dimensions [mm]	102 x 34 x 24	135 x 51 x 30	135 x 51 x 30	216 x 111 x 45
Conductor Diameter	15 mm	20 mm	20 mm	52 mm
Operating Temperature	-10 °C to +55 °C	-40 °C to +70 °C	-40 °C to +70 °C	-40 °C to +70 °C
Operating Humidity	up to 85 % (not condensing)	up to 85 % (not condensing)	up to 85 % (not condensing)	up to 85 % (not condensing)
Safety Standards	EN61010-2 EN61010-2-032:2012	EN61010-2 EN61010-2-032:2012	EN61010-2 EN61010-2-032:2012	EN61010-2 EN61010-2-032:2012
Safety	CAT III 600V CAT IV 300V	CAT III 600V CAT IV 300V	CAT III 600V CAT IV 300V	CAT III 600V CAT IV 300V
EMC Standards	EN61326-1:2013	EN61326-1:2013	EN61326-1:2013	EN61326-1:2013
PWR-MCTS2 needed	No	No	No	No
Compatible Amplifiers	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe
Cable length	2 m	1.4 m	1.4 m	1.4 m
Data Sheet	DS-CLAMP-5AC	DS-CLAMP-15AC	DS-CLAMP-200AC	DS-CLAMP-1000AC

Specifiche tecniche dei trasduttori di flusso zero

	CT 100		CT 200		CT 400		CT 500		CT 1000		CT 2000
Type	Zero-Flux		Zero-Flux		Zero-Flux		Zero-Flux		Zero-Flux		Zero-Flux
Primary Current Range DC RMS Sinus	100 A		200 A		400 A		500 A		1000 A		2000 A
Conversion ratio	1:500		1:1000		1:1500		1:750		1:1500		1:2000
Overload Ability Short Time (100 ms)	20 kApk		20 kApk		20 kApk		5000 Apk		5000 Apk		10000 Apk
Max. measurement resistor (100 % of Ip)	25 Ω		20 Ω		10 Ω		5 Ω		4 Ω		3.5 Ω
Step response (0 ... 90%)	0.2 μs		0.2 μs		1 μs		1 μs		1 μs		1 μs
Temperature influence	0.2 ppm/K		0.2 ppm/K		0.1 ppm/K		1 ppm/K		0.3 ppm/K		< 0.1 ppm/k
Nominal secondary current	200 mA at 100 A		200 mA at 200 A		266 mA at 400 A		666 mA at 500 A		666 mA at 1000 A		1 A at 2000 A
Bandwidth ( -3 dB)	DC ... 2 MHz		DC ... 1.1 MHz		DC ... 800 kHz		DC ... 520 kHz		DC ... 440 kHz		DC ... 140 kHz
Linearity	1.5 ppm		1.2 ppm		0.8 ppm		3 ppm		3 ppm		3 ppm
Offset	< 0.0015 %		< 0.0010 %		< 0.0008 %		< 0.00115 %		< 0.0012 %		< 0.0012 %
Accuracy
Frequency	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude	Phase Error	Amplitude ¹	Phase Error ¹
DC	0.002 %	-	0.001 %	-	0.0008 %	-	0.00115 %	-	0.0012 %	-	0.0012 %	-
to 100 Hz	0.015 %	± 0.01 °	0.015 %	± 0.01 °	0.015 %	± 0.01 °	0.015 %	± 0.01 °	0.015 %	± 0.01 °	0.015 %	± 0.01 °
100 - 1 kHz	0.025 %	± 0.05 °	0.02 %	± 0.02 °	0.02 %	± 0.01 °	0.02 %	± 0.01 °	0.02 %	± 0.01 °	0.05 %	± 0.05 °
1 kHz - 10 kHz	0.2 %	± 0.1 °	0.15 %	± 0.05 °	0.15 %	± 0.1 °	0.1 %	± 0.05 °	0.15 %	± 0.1 °	0.25 %	± 0.1 °
10 kHz - 20 kHz	0.5 %	± 0.25 °	0.5 %	± 0.25 °	0.5 %	± 0.5 °	0.2 %	± 0.5 °	1.5 %	± 1 °	1 %	± 1 °
20 kHz - 50 kHz	0.5 %	± 0.25 °	0.5 %	± 0.25 °	0.5 %	± 0.5 °	0.2 %	± 0.5 °	1.5 %	± 1 °	-	-
50 kHz - 100 kHz	1 %	± 0.5 °	1 %	± 0.5 °	1 %	± 1 °	0.5 %	± 1 °	4 %	± 2 °	-	-
General Specifications
Rated isolation voltage RMS, single isolation CAT III, pollution deg. 2, IEC 61010-1 standards, EN 50178 standards	1000 V		1000 V		1000 V		1000 V		1000 V		1000 V
Test voltage 50 / 60 Hz, 1 min	4.95 kV		4.95 kV		4.95 kV		4.2 kV		4.2 kV		6 kV
Inner diameter	28 mm		28 mm		28 mm		38 mm		38 mm		70 mm
Dimensions	93 x 78.8 x 49.5		94 x 78.8 x 49.5		95 x 78.8 x 49.5		128 x 106 x 54		128 x 106 x 54		231 x 220 x 76
Supply voltage (±5 %)	±15 V		±15 V		±15 V		±15 V		±15 V		±15 V
Operating humidity	20 % to 80 % (not condensing)		20 % to 80 % (not condensing)		20 % to 80 % (not condensing)		20 % to 80 % (not condensing)		20 % to 80 % (not condensing)		20 % to 80 % (not condensing)
Operating temperature	- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C		- 40 °C to + 85 °C
DEWESoft® Shunt	5 Ω		5 Ω		5 Ω		1 Ω		1 Ω		1 Ω
PWR-MCTS2 needed	Yes		Yes		Yes		Yes		Yes		Yes
Compatible amplifiers (see 1)	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe		SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe
Cable length	5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS		5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS		5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS		5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS		5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS		5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS
Data Sheet
1) The ranges of the IOLITE and KRYPTON amplifiers might affect the resolution of the measured values.

Caratteristiche tecniche delle bobine Rogowski in c.a.

	DS-FLEX-3000-17	DS-FLEX-3000-35	DS-FLEX-3000-35HS	DS-FLEX-3000-80	DS-FLEX-30000-120
Type	Rogowski coil	Rogowski coil	Rogowski coil	Rogowski coil	Rogowski coil
Current Range	3 A, 30 A, 300 A, 3000 A AC RMS	3 A, 30 A, 300 A, 3000 A AC RMS	3000 A AC RMS	3 A, 30 A, 300 A, 3000 A AC RMS	30 A, 300 A, 3000 A, 30000 A AC RMS
Sensitivity	1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A	1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A	1 mV/A	1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A	100 mV/A, 10 mV/A, 1 mV/A, 0.1 mV/A
Accuracy (+25 °C)	≤ 1.5 %	≤ 1.5 %	≤ 1.0 %	≤ 1.5 %	≤ 1.5 %
Phase Error @ 50 Hz	≤ 1.0 deg	≤ 1.0 deg	≤ 1.0 deg	≤ 1.0 deg	≤ 1.0 deg
Bandwidth	3 A: 10 Hz to 10 kHz Others: 10 Hz to 20 kHz	3 A: 10 Hz to 10 kHz Others: 10 Hz to 20 kHz	5 Hz - 1MHz	3 A: 10 Hz to 10 kHz Others: 10 Hz to 20 kHz	30 A: 10 Hz to 5 kHz Others: 10 Hz to 20 kHz
TEDS	Not supported	Not supported	Fully supported	Not supported	Not supported
Noise	≤ 0.04 Arms	≤ 0.04 Arms	≤ 0.04 Arms	≤ 0.04 Arms	≤ 0.04 Arms
Temperature Coefficient	≤ 0.5 % / 10 °C	≤ 0.5 % / 10 °C	≤ 0.5 % / 10 °C	≤ 0.5 % / 10 °C	≤ 0.5 % / 10 °C
General Specifications
Casing Dimensions [mm]	120 x 58 x 36	120 x 58 x 36	140 x 64 x 28	120 x 58 x 36	120 x 58 x 36
Coil Length	170 mm	350 mm	350 mm	800 mm	1200 mm
Coil Diameter	45 mm	100 mm	100 mm	250 mm	380 mm
Power Supply	+5 V	+5 V	+9 V	+5 V	+5 V
Operating Temperature	- 10 °C to + 55 °C	- 10 °C to + 55 °C	- 10 °C to + 55 °C	- 10 °C to + 55 °C	- 10 °C to + 55 °C
Operating Humidity	up to 90 % (not condensing)	up to 90 % (not condensing)	up to 90 % (not condensing)	up to 90 % (not condensing)	up to 90 % (not condensing)
Safety Standards	EN60529 EN61010-2 EN61010-2-032:2012	EN60529 EN61010-2 EN61010-2-032:2012	EN60529 EN61010-2 EN61010-2-032:2012	EN60529 EN61010-2 EN61010-2-032:2012	EN60529 EN61010-2 EN61010-2-032:2012
Safety	CAT IV 600V	CAT IV 600V	CAT III 1000V	CAT IV 1000V	CAT IV 1000V
EMC Standards	EN61326-1:2013	EN61326-1:2013	EN61326-1:2013	EN61326-1:2013	EN61326-1:2013
PWR-MCTS2 needed	No	No	No	No	No
Compatible amplifiers	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 *not tested yet with IOLITE and KRYPTON modules	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 *not tested yet with IOLITE and KRYPTON modules
Cable length	2.5 m (Extendable to 10 m upon request)	2.5 m (Extendable to 10 m upon request)	2.5 m (Extendable to 10 m upon request)	2.5 m (Extendable to 10 m upon request)	2.5 m (Extendable to 10 m upon request)
Data Sheet	DS-FLEX-3000-17	DS-FLEX-3000-35	DS-FLEX-3000-35HS	DS-FLEX-3000-80	DS-FLEX-30000-120


DS-FLEX-CWTUM6-1200A
Type	Rogowski coil
Peak current	1200 A
Sensitivity	5 mV/A
Accuracy	max. ± 2 % of reading
Linearity	0.05 % of reading
DC offset	max. ± 3 mV (@ 25°C)
Bandwidth	3.2 Hz (-3 dB) ... 30 MHz (-3 dB)
Noise	max. 10 mVpp
TEDS	Supported
di/dt	70 kA/us (peak) 1.2 kA/us (rms)
General Specifications
Coil Length	80 mm
Coil Cross Section	1.7 mm
Operating Temperature	- 40 °C to + 125 °C
Overvoltage protection	1.2 kVpeak (rating established @ 3 kVrms, 50 Hz, 60 s flash test)
PWR-MCTS2 needed	No
Compatible amplifiers	SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43
Cable length	1 m

Specifiche tecniche dell'alimentatore MCTS

	SIRIUSi-PWR-MCTS2 / SIRIUSir-PWR-MCTS	SIRIUSi-HD-PWR-MCTS2 / SIRIUSir-HD-PWR-MCTS
Power supply	9 - 36 V DC	9 - 36 V DC
Max power consumption	85 W	85 W
Physical dimensions	265 x 140 x 65 mm	265 x 140 x 65 mm
Operating temperature	-20 °C to 50 °C	-20 °C to 50 °C
Storage temperature	-40 °C to 85 °C	-40 °C to 85 °C
Humidity (@ 60 °C)	95 % RH non-condensing	95 % RH non-condensing
Output	4 x Isolated Power supply (1500 V DC, 60 sec)	8 x Isolated Power supply (1500 V DC, 60 sec)
Output voltage	±15 V DC	±15 V DC
Maximum output per channel	20 W	20 W
Short circuit protection	indefinite (automatic recovery)	indefinite (automatic recovery)
Overload protection	150 % of Iout max. typ	150 % of Iout max. typ

DSi-PWR-MCTS-SINGLE

	DSi-PWR-MCTS-SINGLE
Power supply	9 - 36 V DC
Max power consumption	39 W
Power IN connector	Lemo 1B 2-pin male
Power OUT connector	Lemo 1B 2-pin female
Physical dimensions	98 x 125 x 32 mm
Operating temperature	-20 °C to 50 °C
Storage temperature	-40 °C to 85 °C
Humidity (@ 60 °C)	95 % RH non-condensing
Output	1 x Isolated Power supply (1500 V DC, 60 sec)
Output voltage	±15 V DC
Maximum output per channel	39 W
Short circuit protection	indefinite (automatic recovery)
Overload protection	150 % of Iout max. typ
Sensor connector	D-SUB9 female
Amplifier connector	D-SUB9 male

Torna all'inizio