Tech specs - SIRIUS® XHS 

Desenhos técnicos

SIRIUS XHS
 
SIRIUS XHS
SIRIUS XHS-PWR

SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing

SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing
SIRIUS® XHS  technical drawing

Especificações técnicas

Especificações Gerais

Power
Power Supply 9 - 48 V DC
Power consumption Typ. 30 W
Environmental
Operating Temperature -10 to 50 °C
Storage Temperature -40 to 85 °C
Humidity 5 to 95 % RH non condensing @ 60 °C
IP rating IP20
Shock & Vibration
Shock (EN 60068-2-27:2009)
75 g, 6 ms, half-sine (25x pos./neg in each ahis)
Random Vibration (EN 60721-3-2: 1997 - Class 2M2)
Sweep sinus Vibration (EN 60068-2-6:2008)
Interfaces
Ethernet
1 GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45)
USB USB 3.0 (Type C)
CAN CAN 2.0 (DSUB9)
Sync Input/Ouput
Level (Input/Output) TTL compatible
Max. Output Current ±24 mA (±50 mA for 1 sec)
Max. Sync-cable length 100 m (Master/Slave), 200 m (IRIG)

Filtro ADC

ADC
Type HybridADC
High bandwidth mode 16 bit SAR, up to 15 Ms/sec
Alias free mode 24 bit Sigma Delta, up to 2 Ms/sec
Digital low pass filter Software selectable (off, alias free)
Analog HW filter Analog 1 MHz 6th order (Butterworth)
Alias free filter 0.5*fs cutoff, 0.45*fs pass band, 0.55*fs stop band to -100dB, zero phase distortion, available below 2Ms/sec

Especificação de amplificadores

Visão global

XHS-HV XHS-LV XHS-ACC
Connectors BANANA DB9, BNC BNC
Channels per slice 8
Data rate / channel 15 MS/s
Resolution 16-bit (24-bit @ 1 MS/s)
Bandwidth 5 MHz
Voltage ranges ±2000 V ... ±200 V ±100 V ... ±50 mV ±10 V ... ±200 mV
Input coupling DC DC, AC 1 Hz DC, AC 0.1 Hz, AC 1 Hz
Sensor excitation 2.5..30 V bipolar, 2..24 V unipolar, max. 0.2 A / 2 W IEPE 2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA
Bridge connection Full
Programmable shunt
IEPE input DSI-ACC
Resistance
Temperature (PTx) DSI-RTD
Thermocouple DSI-TH
Potentiometer
LVDT DSI-LVDT
Charge DSI-CHG
Current ext. shunt
DSI20mA, DSI5A
ext. shunt
TEDS
Isolation voltage CATII 1000 V 1000 V 1000 V
Power consumption per channel 1 W/ch 1.2 W/ch TBD
Advanced functions High voltage, high bandwidth, high isolation High sensor excitation and multi range Sensor error detection, high speed

Especificações XHS-HV

Inputs Voltage
ADC Type HybridADC - 24-bit alias free up to 1 MS/s, 16-bit up to 15 MS/s
Sampling Rate Simultaneous 15 MS/s
Filtering AAF 1 MHz (6th order)
Analogue bandwidth (-3 dB)
5 MHz
Voltage ranges ±2000 V, ±1000 V, ±400 V, ±200 V
Input Accuracy Signal frequency Accuracy
DC ±0.03 % of reading ±0.02 % of range ±0.04 V
Up to 1kHz ±0.03 % of reading ±0.02 % of range
Up to 10 kHz ±0.1 % of reading ±0.05 % of range
Up to 100 kHz ±4 % of reading ±0.1 % of range
Up to 1000 kHz ±5 % of reading ±0.5 % of range
Noise floor, Typ.
Sample rate / Range →
2000 V 1000 V 400 V 200 V
15 MS/s -88 dB -87 dB -85 dB -81 dB
1 MS/s -97 dB -94 dB -89 dB -83 dB
100 kS/s -108 dB -107 dB -101 dB -96 dB
10 kS/s -118 dB -117 dB -111 dB -106 dB
CMR, Typ. (Min.) 101 dB (88 dB) @ 50 Hz, 75 dB (68 dB) @ 400 Hz
Channel Crosstalk -116 dB typ. @ 50 Hz, -89 dB typ. @ 1 kHz
Gain Drift Typical 20 ppm/K, max. 40 ppm/K
Offset Drift Typical 1.5 mV/K + 1 ppm of range/K, max 3 mV/K + 2 ppm of range/K
Gain Linearity < 0.01 %
Input Coupling DC
Input Impedance 10 MΩ || 1 pF
Protection class CAT III 600 V; CAT II 1000 V
Additional Specifications
Input connector Banana
Rev: 1608804000

Especificação XHS-LV

Inputs Voltage
ADC Type HybridADC - 24-bit alias free up to 1 MS/s, 16-bit up to 15 MS/s
Sampling Rate Simultaneous 15 MS/s
Filtering AAF 1 MHz (6th order)
Analogue bandwidth (-3 dB) 5 MHz
Voltage ranges ±100, 50, 20, 10, 5, 2, 1, 0.5, 0.2, 0.1 and 0.05 V
Input Accuracy DC ±0.03 % of reading ±0.02 % of range ±100 μV (2 mV for Ranges ≥ 10 V)
Up to 1 kHz ±0.03 % of reading ±0.02 % of range
Up to 10 kHz ±0.1 % of reading ±0.05 % of range
Up to 100 kHz ±2 % of reading ±0.1 % of range
Up to 1000 kHz ±5 % of reading ±0.5 % of range
Noise floor, Typ.
Sample rate, filter \ Range →
100 V 5 V 0.5 V 0.05 V
15 MS/s, Filter off -82 dB -82 dB -75 dB -58 dB
1 MS/s, Filter on -91 dB -93 dB -85 dB -71 dB
100 kS/s, Filter on -102 dB -103 dB -95 dB -79 dB
10 kS/s, Filter on -111 dB -112 dB -105 dB -85 dB
CMR, Typ. (Min)
Frequency \ Range → 100 V 5 V 1 V 0.05 V
50 Hz 91 dB (70 dB) 102 dB (83 dB) 100 dB (88 dB) 100 dB (88 dB)
400 Hz 86 dB (69 dB) 102 dB (83 dB) 99 dB (88 dB) 98 dB (87 dB)
10 kHz 66 dB (60 dB) 81 dB (77 dB) 83 dB (79 dB) 83 dB (79 dB)
Channel Crosstalk Range ≥ 10 V: -105 dB @ 10 kHz
Range < 10 V: -120 dB @ 10 kHz
Gain Drift Typical 10 ppm/K, max. 30 ppm/K
Offset Drift Range ≥ 10 V: Typ. 70 μV/K + 1 ppm of range/K, Max 200 μV/K + 5 ppm of range/K
Range < 10 V: Typ. 4 μV/K + 1 ppm of range/K, Max 8 μV/K + 2 ppm of range/K
Gain Linearity < 0.03 %
Input Coupling (see 1) DC, AC 1 Hz (3 Hz, 10 Hz per SW)
Input Impedance Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ || 110 pF between INx to GND
Excitation Voltage Unipolar or Bipolar Software selectable (programmable 16-bit DAC)
Excitation Level unipolar 2 .. 24 V; Predefined levels: 2, 2.5, 5, 10, 12, 15, 20 and 24 VDC
Excitation Level bipolar 2.5 .. 30 V; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC
Drift ±10 ppm/K ±150 μV/K
Stability 10% to 90% load (bipolar) < 0.01 %
Current limit 200 mA (2 Watt max. per Channel, 12 Watt max. per Slice)
Additional Specifications
Input connector DSUB 9, BNC (others on request)
TEDS support Standard + DSI® adapters
Rev: 1608804000
1) In- must be within ±10V referred to GND(iso); for Ranges ≥ 10 V the DC value of In- is not rejected

Shunt de corrente SIRIUS XHS

Especificações Gerais

Power
Power Supply
9 - 36 V DC
PoE (RJ45)
PWR IN (Lemo 1B 2-pin)
Power consumption Typ. 30 W
Environmental
Operating Temperature
-40 to 70 °C
Storage Temperature
-40 to 85 °C
IP rating IP67
Shock & Vibration TBD
Intrerfaces
Ethernet
GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45)
CAN CAN 2.0 (DSUB9)
Sync Input/Output
Level (Input/Output) TTL compatible
Max. Output Current ±24 mA (±50 mA for 1 sec)
Max. Sync-cable length
100 m (Master/Slave), 200 m (IRIG)
Additional Specifications
Interlock YES (chassis covers + cables)

Especificações do transdutor de corrente DC-CT

Inputs Current
ADC Type HybridADC - 24-bit alias free up to 1 MS/s, 16-bit up to 15 MS/s
Sampling Rate Simultaneous 15 MS/sec
Filtering AAF 1MHz (5th order)
Current Ranges 1000 A 500 A 100 A
Sensitivity 4 mV/A 8 mV/A 40 mV/A
Recommended cable size 95 mm2 50 mm2 25 mm2
Recommended PG cable gland M32 M25 M16
Recommended grounding cable size
50 mm2 25 mm2 16 mm2
Offset Accuracy ± 50 mA
Gain linearity < 0.01%
Flatnesss (DC-10kHz) ±50 mdB
Bandwidth (-3 dB) >500 kHz
1