Tekniska specifikationer för SIRIUS® XHS

SIRIUS® XHS systemspecifikationer
Tekniska specifikationer för SIRIUS® XHS HybridADC
Tekniska specifikationer för SIRIUS® XHS standarddisk
SIRIUS® XHS räknare med variabla triggerspecifikationer
Specifikationer för SIRIUS® XHS ACC-förstärkare
Specifikationer för SIRIUS® XHS CHG-förstärkare
Specifikationer för SIRIUS® XHS LV-förstärkare

SIRIUS® XHS systemspecifikationer

Power specs
Power Supply	9 - 48 V DC
Power consumption	Typ. 30 W
Environmental
Operating Temperature	-10 to 50 °C
Storage Temperature	-40 to 85 °C
Humidity	5 to 95 % RH non condensing @ 60 °C
IP rating	IP20
Shock & Vibration	Shock (EN 60068-2-27:2009) 75 g, 6 ms, half-sine (25x pos./neg in each axis) Random Vibration (EN 60721-3-2: 1997 - Class 2M2) Sweep sinus Vibration (EN 60068-2-6:2008)
Dimensions	266 mm x 149 mm x 55 mm 266 mm x 149 mm x 69 mm (extended slice)
Weight	2,4 kg
Interfaces
Ethernet	1 GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45)
USB	USB 3.0 (Type C)
CAN	CAN 2.0, CAN-FD (DSUB9)
Sync Input/Ouput
Level (Input/Output)	TTL compatible
Max. Output Current	±24 mA (±50 mA for 1 sec)
Synchronization
Delay between slices	± 1 μs ( to the reference clock )
Max. Sync-cable length	100 m (Master/Slave), 200 m (IRIG)

Tekniska specifikationer för SIRIUS® XHS HybridADC

ADC
Type	Hybrid ADC
High bandwidth mode	16-bit SAR, up to 15 MS/s
High dynamic mode	Alias-free up to 2 MS/s
Low pass filter	Software selectable (Off, 1 MHz, AAF)
Analog HW filter	Software selectable, Analog 1 MHz 6th order (Butterworth)
Alias free filter (AAF)	0.5fs cutoff, 0.45fs pass band, 0.55*fs stop band to -100 dB, zero phase distortion, available below 2 MS/s

Tekniska specifikationer för SIRIUS® XHS standarddisk

Counter Input
Input Channels (See 1)	8
Modes	Event counting, waveform timing, encoder, tacho, geartooth, ...
Counter timebase	150 MHz
Time base accuracy	Typical: 0.5 ppm, Max: 2 ppm
Max. Sampling Rate	5 MS/s
Max. Bandwidth	15 MHz
Input Filter	Off, 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Counter resolution	32-bit
Input Compatibility, Level	3.3 V TTL/CMOS (Low: <0.8 V, High >2 V)
Input termination, impedance	100 kΩ pull-up to +3.3 V
Input Protection	±25 V continuous
Digital Output
Output Channels	8 connectors, 1 line per connector
Output	5 V digital output
Maximum current	32 mA single output, 100 mA total
Output series resistance	50 Ω
Sensor Power Supply
Output Voltage +5 V	5 V +/- 10 % 500 mA typ. Output short protected (Shared between 8 ports)
Output Voltage +12 V (See 2)	12 V +/-10 % 300 mA typ. Output short protected (Shared between 8 ports)
1) Digital inputs on Counter (individual A, B, Z input) can be used only for Trigger condition 2) Maximum 2x DS-TACHO4 laser probes supported.
Rev: 1775113000

SIRIUS® XHS räknare med variabla triggerspecifikationer

Input
Input Channels	8
Modes	Event counting, waveform timing, encoder, tacho, geartooth, ...
Counter timebase	150 MHz
Time base accuracy	Typical: ±0.5 ppm, Max: ±2 ppm
Max. Sampling Rate	5 MS/s
Analog bandwidth	-3 dB @ 8 MHz min, 15 MHz typ
Input Filter	Off, 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Counter resolution	32-bit
Input impedance	1 MΩ \| 8 pF
Digital Output
Output Channels	8
Output	5 V
Maximum current	32 mA single output, 100 mA total
Output series resistance	50 Ω
Sensor Power Supply
Output Voltage +5 V	5 V ±10 % 500 mA typ. Output short protected (Shared between 8 ports)
Output Voltage +12 V (See 1)	12 V ±10 % 500 mA typ. Output short protected (Shared between 8 ports)
Additional features
Input compatibility	Adjustable trigger levels
Trigger adjustment range	-2 V to 50 V
Trigger resolution	13 mV
Trigger level accuracy	±60 mV ±0.2 % of threshold / retrigger level
Max. input DC voltage @AC coupling	±50 VDC
Overvoltage protection	±100 VDC
1) Maximum 2x Tacho-4 laser probes supported.
Rev: 1775113000

Specifikationer för SIRIUS® XHS ACC-förstärkare

SIRIUSi XHS 8xACC IEPE data acquisition system

Inputs
Input types	Voltage, IEPE
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±10, 5, 2, 1, 0.4 and 0.2 V
Input Accuracy	DC	±0.03 % of reading ±0.02 % of range ±50 μV
	Up to 1 kHz	±0.04 % of reading ±0.02 % of range
	Up to 10 kHz	±0.06 % of reading ±0.05 % of range
	Up to 100 kHz	±0.1 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate, filter \ Range →	10 V	5 V	2 V	1 V	0.4 V	0.2 V
	15 MS/s, Filter off	-85 dB	-84 dB	-83 dB	-82 dB	-77 dB	-72 dB
	1 MS/s, Filter on	-98 dB	-98 dB	-97 dB	-95 dB	-92 dB	-87 dB
	100 kS/s, Filter on	-109 dB	-107 dB	-108 dB	-107 dB	-103 dB	-98 dB
	10 kS/s, Filter on	-119 dB	-119 dB	-119 dB	-118 dB	-114 dB	-109 dB
CMR, Typ.	Frequency \ Range →	10 V	5 V	2 V	1 V	0.4 V	0.2 V
	50 Hz	141 dB	141 dB	139 dB	133 dB	121 dB	120 dB
	400 Hz	130 dB	133 dB	136 dB	137 dB	137 dB	131 dB
	1 kHz	122 dB	125 dB	127 dB	129 dB	130 dB	131 dB
Gain Drift	Typical 10 ppm/K, max. 30 ppm/K
Offset Drift	Typical 0.5 μV/K + 1 ppm of range/K, max. 2 μV/K + 4 ppm of range/K
Gain Linearity	< 0.02 %
Inter Channel Phase-mismatch	0.005° * fin [kHz] + 0.0002°
Channel Cross talk	-145 dB typ. @ 1 kHz
Input Coupling	DC or AC (1 Hz, 0.1 Hz)
Input Impedance	1 MΩ
Overvoltage Protection	50 V continuous; 200 V peak (10 msec)
Max. common mode voltage Isolation voltage	140 Vdc (100 Vacrms)
IEPE mode
Excitation	2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA
Compliance voltage	24 V
Output Impedance	> 10 kΩ
Sensor detection	Shortcut: < 4 V; Open: > 19 V
Additional Specifications
Input connector	BNC
TEDS support	IEPE mode only
Rev: 1623052800

Specifikationer för SIRIUS® XHS CHG-förstärkare

SIRIUSi-XHS-8xCHG - 8-channel high-speed charge amplifier DAQ module

Inputs
Input types	Voltage IEPE Charge
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±10 V, ±5 V, ±1 V, ±0.5 V, ±0.1 V
Input Accuracy	DC	±0.03 % of reading ±0.02 % of range ±50 μV
	Up to 1 kHz	±0.04 % of reading ±0.02 % of range
	Up to 10 kHz	±0.06 % of reading ±0.05 % of range
	Up to 100 kHz	±0.1 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate, filter \ Range →	10 V	5 V	1 V	0.5 V	0.1 V
	15 MS/s, Filter off	-75 dB	-75 dB	-74 dB	-73 dB	-53 dB
	1 MS/s, Filter on	-89 dB	-89 dB	-88 dB	-88 dB	-80 dB
	100 kS/s, Filter on	-99 dB	-99 dB	-98 dB	-98 dB	-89 dB
	10 kS/s, Filter on	-109 dB	-109 dB	-107 dB	-107 dB	-95 dB
CMR, Typ.	Frequency \ Range →	10 V	5 V	1 V	0.5 V	0.1 V
	50 Hz	133 dB	135 dB	122 dB	124 dB	108 dB
	400 Hz	128 dB	130 dB	133 dB	131 dB	117 dB
	10 kHz	98 dB	99 dB	106 dB	108 dB	107 dB
Channel Cross talk	< -160 dB typ. @ 1 kHz
Gain Drift	Typical 10 ppm/K, max. 30 ppm/K
Offset Drift	Typical 2 μV/K + 1 ppm of range/K, max 8 μV/K + 3 ppm of range/K
Gain Linearity	< 0.02 %
Inter Channel Phase-mismatch	0.005° * fin [kHz] + 0.0002°
Input Coupling	DC or AC (0.1 Hz, 1 Hz)
Input Impedance	10 MOhm
Overvoltage Protection	50 V continuous; 200 V peak (10 msec)
Max. common mode voltage Isolation voltage	100 Vdc (100 Vacrms)
IEPE mode
Ranges	±10 V, ±5 V, ±1 V, ±0.5 V, ±0.1 V
Excitation	2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA
Compliance voltage	24 V
Output Impedance	> 10 kΩ
Sensor detection	Shortcut: < 4 V; Open: > 19 V
Charge mode
Charge ranges	±500000 pC, ±50000 pC, ±10000 pC, ±5000 pC, ±1000 pC
Input Accuracy	±0.5 % of reading ±0.05 % of range ±2 pC
Input Coupling	±500000 pC range: - DC (filter off) - 1.45 mHz (time constant > 100 s) - 14.5 mHz (time constant > 10 s) - 145 mHz (time constant > 1 s) ±50000 pC, ±10000 pC, ±5000 pC, ±1000 pC range: - DC (filter off) - 14.5 mHz (time constant > 10 s) - 145 mHz (time constant > 1 s) - 1.45 Hz (time constant > 0.1 s) ±20 % cutoff frequency accuracy
DC drift	typ. < 1 pC/s, max. 5 pC/s
Charge injection	1 Vrms, 20 Hz, ±3 % accuracy
Additional Specifications
Input connector	BNC (others on request)
TEDS support	IEPE mode only
Rev: 1775113000

Specifikationer för SIRIUS® XHS LV-förstärkare

Inputs	Voltage
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±100, 50, 20, 10, 5, 2.5, 1, 0.5, 0.25, 0.1 and 0.05 V
Input Accuracy	DC	±0.03 % of reading ±0.02 % of range ±100 μV (2 mV for Ranges ≥ 10 V)
	Up to 1 kHz	±0.03 % of reading ±0.02 % of range
	Up to 10 kHz	±0.1 % of reading ±0.05 % of range
	Up to 100 kHz	±2 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate, filter \ Range →	100 V	5 V	0.5 V	0.05 V
	15 MS/s, Filter off	-82 dB	-78 dB	-65 dB	-51 dB
	1 MS/s, Filter on	-94 dB	-95 dB	-88 dB	-69 dB
	100 kS/s, Filter on	-104 dB	-105 dB	-100 dB	-81 dB
	10 kS/s, Filter on	-113 dB	-114 dB	-107 dB	-87 dB
CMR, Typ.	Frequency \ Range →	100 V	5 V	0.5 V	0.05 V
	50 Hz	91 dB	102 dB	98 dB	100 dB
	400 Hz	86 dB	75 dB	90 dB	98 dB
	10 kHz	66 dB	74 dB	82 dB	83 dB
Channel Crosstalk	Range ≥ 10 V: -105 dB @ 10 kHz Range < 10 V: -120 dB @ 10 kHz
Gain Drift	Typical 10 ppm/K, max. 30 ppm/K
Offset Drift	Range ≥ 10 V: Typ. 100 μV/K + 1 ppm of range/K, Max 250 μV/K + 2 ppm of range/K Range < 10 V: Typ. 4 μV/K + 1 ppm of range/K, Max 8 μV/K + 2 ppm of range/K
Gain Linearity	< 0.03 %
Input Coupling (see 1)	DC, AC 1 Hz
Input Impedance	Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ \| 110 pF between INx to GND
Overvoltage Protection	Range ≥ 10 V: 300 V continuous Range < 10 V: 100 V (200 V peak for 10 msec)
Max. common mode voltage Isolation voltage	420 Vdc (300 Vacrms)
Excitation Voltage
Polarity	Unipolar or Bipolar Software selectable (programmable 16-bit DAC)
Excitation Level	Unipolar 1 .. 24 V; Predefined levels: 1, 2, 2.5, 5, 10, 12, 15, 20 and 24 VDC
Excitation Level	Bipolar 2.5 .. 30 V; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC
Drift	±10 ppm/K ±150 μV/K
Stability 10% to 90% load (bipolar)	< 0.01 %
Current limit	200 mA (2 Watt max. per Channel, 12 Watt max. per Slice)
Additional Specifications
Input connector	DSUB 9, BNC, Banana (others on request)
TEDS support	Standard + DSI® adapters
Rev: 1701403200
1) In- must be within ±10 V referred to GND (iso); for Ranges ≥ 10 V the DC value of In- is not rejected