Tekniska specifikationer för KRYPTON®

KRYPTON® ONE allmänna specifikationer

Interface
Data interface	EtherCAT®
Data rate	100Mbps Full Duplex bus speed
Sync Accuracy	below 1 sample to Sirius®
EtherCAT®	Max. Cable Length 100 m
Max. Throughput per Chain	From 6 MB/s to 10 MB/s
Max. Number of Units	64 or more (power injectors may be required)
Data Interface Connection	LEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable
Power
Power Supply	9 - 50 V DC
Power consumption	1 - 3 W
Environmental
Operating Temperature	-40 to 85 °C
Storage Temperature	-40 to 85 °C
Humidity	5 to 100 % RH
IP rating	IP65 / IP67 (see individual specifications for details)
Shock	Shock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total
Vibration	Random vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total
Rev: 1557765000

KRYPTON® MULTI allmänna systemspecifikationer

Interface
Data interface	EtherCAT®
Data Rate	100 Mbps Full Duplex bus speed
Max. Throughput per Chain	From 6 MB/s to 10 MB/s (see 1)
Sync Accuracy	below 1 sample to Sirius®
EtherCAT®	Max. Cable Length 100 m
Max. Number of Units	64 or more (power injectors may be required)
Data Interface Connection	LEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable
Additional Specifications
Power supply ground to mechanical ground (housing) resistance	> 100 kΩ
Power
Power Supply	9 - 48 V DC
Environmental
Operating Temperature	-40 to 85°C
Storage Temperature	-40 to 85°C
Humidity	5 to 100 % RH
IP rating	IP65 / IP67
Shock	Shock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total
Vibration	Random vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total
1) It depends on the devices connected, numbers of channels, configuration, length of cables and other parameters.
Rev: 1673526968

Översikt över KRYPTON® ONE-förstärkare

	AO	DI	DO	ACC	STG	LV	HV	TH-HV	CNT
Connector	BNC	DSUB15HD Male	DSUB15HD Female	BNC	DB9	BNC	Banana jack	K-type Thermocouple LEMO REDEL	LEMO T-type 7pin female
Number of channels per module	1	4	4	1	1	1	1	1	1
Data rate per channel	✗	40 kS/s	✗	40 kS/s	40 kS/s	40 kS/s	40 kS/s	100 S/s	20 kS/s
Resolution	18 bit	Digital	Digital	24-bit	24-bit	24-bit	24-bit	24-bit	100 MHz timebase 5 ppm, 20 ppm max
Bandwidth	✗	✗	✗	0.49 fs	0.49 fs	0.49 fs	0.49 fs	0.49 fs	10 MHz
Voltage ranges	✗	Digital (Low: < 1 V, High: > 2 V)	✗	±10 V ±5 V ±1 V ±200 mV	±50 V ±10 V ±1 V ± 100 mV	±50 V ±10 V ±1 V ±100 mV	±1000 V	Thermocouple	TTL (Low: <0.8 V, High > 2 V)
Input coupling				DC, AC 0.1 Hz, 1 Hz	DC, AC 1 Hz	DC, AC 1 Hz	DC
Sensor excitation	±10 V	✗	✗	IEPE 4 mA, 8 mA	Unipolar 0 - 24 V Bipolar 0 - 12 V	✗	✗	✗	5 V (100 mA max.), 12 V (90 mA max.)
Bridge connection	✗	✗	✗	✗	Full, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire	✗	✗	✗	✗
Programmable shunt	✗	✗	✗	✗	100 kΩ	✗	✗	✗	✗
IEPE input	✗	✗	✗	✓	DSI-ACC	✗	✗	✗	✗
Resistance	✗	✗	✗	✗	✓	✗	✗	✗	✗
Temperature (PTx)	✗	✗	✗	✗	DSI-RTD	✗	✗	✗	✗
Thermocouple	✗	✗	✗	✗	DSI-TH	✗	✗	K-type	✗
Current	✗	✗	✗	✗	20mA (internal shunt), DSI-5A, ext. shunt	ext. shunt	✗	✗	✗
Potentiometer	✗	✗	✗	✗	✓	✗	✗	✗	✗
LVDT	✗	✗	✗	✗	DSI-LVDT	✗	✗	✗	✗
Charge	✗	✗	✗	✗	DSI-CHG	✗	✗	✗	✗
TEDS	✗	✗	✗	✓	✓	✗	✗	✗	✗
Isolation	None	Galvanic isolation CH, GND	Galvanic isolation CH, GND	125 Vrms Isolation CH, GND	125 Vrms Isolation CH, GND	125 Vrms Isolation CH, GND	CAT III 600 V CAT II 1000 V	CAT III 600 V CAT II 1000 V	None
Power consumption	2 W	1.5 W	2 W	2 W	3 W	1.5 W	1 W	1.3 W	1.2 W
Rev: 1673622000

KRYPTON® MULTI amplifier overview

	STG	TH	TH-HS	RTD	RTD-HS	ACC	LV	LA	DIO	CNT
Connectors	DB9, L2B10f	Thermocouple	Thermocouple	L0B6f	L0B6f	BNC	BNC	BNC	DB25	L1T7f
#ch per module	3x, 6x	8x, 16x	8x, 16x	8x	8x	4x, 8x	4x, 8x	8x	16xDI, 16xDO 8xDI, 8xDO	4xCNT
Data rate / channel	20 kS/s	100 S/s	100 S/s, upgradable to 10 kS/s	100 S/s	100 S/s, upgradable to 10 kS/s	20 kS/s	20 kS/s	20 kS/s	40 kS/s	20 kS/s
Resolution	24-bit	24-bit	24-bit	24-bit	24-bit	24-bit	24-bit	24-bit	digital	100 MHz timebase 5 ppm, 20 ppm max
Bandwidth	0.49*fs	✗	0.49*fs (max. 1 kHz)	✗	✗	0.49*fs	0.49*fs	0.49*fs	✗	10 MHz
Voltage ranges	±10 V, ±1 V, ±100 mV, ±10 mV	±1 V, ±100 mV	±1 V, ±100 mV	±1 V, ±100 mV	±1 V, ±100 mV	±10 V, ±5 V, ±1 V, ±200 mV	±50 V	±20 mA	CMOS compatible	TTL (Low: <0.8 V, High > 2 V)
Input coupling	DC	DC	DC	DC	DC	DC, AC 0.1 Hz, 1 Hz	DC	DC	DC
Sensor excitation	0...15 V max. 0.4 W/ch (45 mA limit)	✗	✗	✗	✗	IEPE 4 mA, 8 mA	-	-	5 V / 300 mA 12 V / 120 mA Vsupply / 200 mA	5 V /100 mA / ch 12 V / 50 mA / ch
Bridge connection	Full, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire	✗	✗	✗	✗	✗	✗	✗	✗	✗
Programmable shunt	100 kΩ	✗	✗	✗	✗	✗	✗	✗	✗	✗
IEPE input	DSI-ACC	✗	✗	✗	✗	✓	✗	✗	✗	✗
Resistance	✗	✗	✗	10 kΩ	10 kΩ	✗	✗	✗	✗	✗
Temperature (PTx)	DSI-RTD	✗	✗	PT100, 200, 500, 1000, 2000	PT100, 200, 500, 1000, 2000	✗	✗	✗	✗	✗
Thermocouple	DSI-TH	K, J, T, R, S, N, E, C, B	K, J, T, R, S, N, E, C, B	✗	✗	✗	✗	✗	✗	✗
Current	ext. shunt DSI	✗	✗	✗	✗	ext. shunt	✗	✗	✗	✗
Potentiometer	✓	✗	✗	✗	✗	✗	✗	✗	✗	✗
LVDT	DSI-LVDT	✗	✗	✗	✗	✗	✗	✗	✗	✗
Charge	DSI-CHG	✗	✗	✗	✗	✗	✗	✗	✗	✗
TEDS	✓	✗	✗	✗	✗	✓	✗	✗	✗	✗
Isolation voltage	Differential	1000 V	1000 V	1000 V	1000 V	Differential	1000 V	1000 V	250 V	✗
Isolation arrangement	None	Ch-Ch & Ch-GND	Ch-Ch & Ch-GND	Ch-Ch & Ch-GND	Ch-Ch & Ch-GND	None	Ch-Ch & Ch-GND	Ch-Ch & Ch-GND	Isolated common GND	Isolated common GND
Power consumption per module	2.4 W (4 W 120 Ω @ 5 V load) 3xSTG; 5.9 W (8.9 W 120 Ω @ 5 V load) 6xSTG	2.5 W (8xTH) 4 W (16xTH)	2.6 W (8xTH-HS) 4.3 W (16xTH-HS)	2.5 W	2.5 W	4.6 W	3.5 W (4xLV) 6.7 W (8xLV)	6.8 W	2 W	2.3W
Advanced functions	Supports all strain types, TEDS support	High isolation, support of main TC types	High isolation, support of main TC types	✗	✗	TEDS support	High isolation, high input range	High isolation, 4-20 mA current loop	✗	SuperCounter®
OBSIDIAN compatibility	Yes* up to 5kHz	Yes	Yes up to 5kHz	No	No	Yes up to 5kHz	Yes up to 5kHz	No	No	Yes
Rev: 1668758400
*Some functions may not be supported

Specifikationer för KRYPTONi-1xACC

Analog inputs
Input types	Voltage, IEPE
Number of channels	1
ADC Type	24-bit SAR with anti-aliasing filter
Sampling Rate	Simultaneous 40 kS/s (50 kS/s while using it standalone) software-selectable
Voltage Mode
Voltage Ranges	±10 V	±5 V	±1 V	±200 mV
Typ. Input Accuracy	±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	90 dB	90 dB	89 dB	88 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	100 dB	99 dB	99 dB	98 dB
Typ. Noise floor @ 10 kS/s	-100 dB	-99 dB	-99 dB	-98 dB
Typical CMR @ 400 Hz / 1 kHz	130 dB / 120 dB	122 dB / 119 dB	104 dB / 97 dB	90 dB / 84 dB
Gain Drift	typ. 10 ppm/K (max. 40 ppm/K)
Offset Drift	typ. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity	< 0.02 %
Input Coupling	DC, AC 0.1 Hz, 1 Hz
Input Impedance	1 MΩ
Overvoltage Protection	In+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
IEPE input
Excitation	4 mA, 8 mA
Compliance voltage	24 V
Output Impedance
Sensor detection	Shortcut: <4 V; Open: >19 V
TEDS support	IEPE mode only
Additional specifications
Input connector	BNC
Isolation	125 Vrms channel to ground isolation
Power
Power supply	9 - 48 V DC
Power consumption	2 W (typ.)
Environmental
IP rating	IP65 / IP67 (see 1)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
1) Depending on the mating connector types
Rev: 1702375200

Specifikationer för KRYPTONi-1xSTG

Analog input
Input types	Voltage, current, full bridge strain, half bridge strain, quarter bridge strain
Number of channels	1
ADC Type	24-bit SAR with anti-aliasing filter
Sampling Rate	Simultaneous 40 kS/s per channel (software-selectable)
Voltage Mode
Ranges	±50 V	±10 V	±1 V	±100 mV
Input Accuracy	±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/s	89 dB	88 dB	88 dB	87 dB
Typical SFDR @ 10 kS/s	100 dB	99 dB	100 dB	96 dB
Typical Noise floor @ 10 kS/s	-103 dB	-99 dB	-103 dB	-96 dB
Typical CMR @ 400 Hz / 1 kHz	71 dB / 66 dB	72 dB / 66 dB	96 dB / 88 dB	96 dB / 87 dB
Gain Drift	Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift	Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity	< 0.02 %
Input Coupling	DC, AC 1 Hz
Input Impedance	1 MΩ		20 MΩ
Overvoltage Protection	200 V		50 V
Current Mode
Ranges	20 mA		2 mA
Input Accuracy	±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor	50 Ω
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Excitation Voltage
Excitation voltage	Free programmable (16-bit DAC)
Predefined Levels	Unipolar 0 - 24 V, Bipolar 0 - 12 V
Accuracy	±0.05 % ±2 mV
Drift	±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load	< 0.01 %
Current Limit	42 mA (400 mW max. Power)
Protection	Continuous short to ground
Bridge mode
Bridge Connection Types	full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Bridge ranges	2…1000 mV/V free programmable
Internal Bridge Completion	½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy	0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor	100 kΩ (others on request)
Shunt Resistor Accuracy	0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust	Software-selectable
Additional specifications
Input connector	DB9
Isolation	125 Vrms channel to ground isolation
TEDS support	Standard + DSI adapters
Power
Power Supply	9 - 48 V DC
Power consumption	2.8 W (typ.)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
Rev: 1710761400

Specifikationer för KRYPTONi-1xLV

Analog input
Input types	Voltage
Number of channels	1
ADC Type	24-bit SAR with anti-aliasing filter
Sampling Rate	Simultaneous 40 kS/s per channel (software-selectable)
Voltage Mode
Ranges	±50 V	±10 V	±1 V	±100 mV
Input Accuracy	±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/s	96 dB	96 dB	94 dB	88 dB
Typical Dynamic Range @ 10 kS	-130 dB	-132 dB	-137 dB	-138 dB
Typical Noise floor @ 10 kS	-108 dB	-102 dB	-107 dB	-100 dB
Gain Drift	Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift	Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity	< 0.02 %
Input Coupling	DC, AC 1 Hz
Input Impedance	1 MΩ		20 MΩ
Overvoltage Protection	200 V		50 V
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Additional specifications
Input connector	BNC
Isolation	125 Vrms channel to ground isolation
Power
Power Supply	9 - 48 V DC
Power consumption	1.5 W (typ.)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
Rev: 1578868200

Specifikationer för KRYPTONi-1xHV

Analog Input
Input types	Voltage
Number of channels	1
ADC Type	24-bit SAR with anti-aliasing filter
Sampling Rate	40 kS/s (software-selectable)
Input range	±1000 V
Input accuracy	±0.03 % of reading ±0.2 V
Typ. Noise floor @ 10 kS/s	-96 dB
Typ. Noise floor @ 40 kS/s	-90 dB
Typ. CMR @ 400 Hz / 1 kHz	-
Gain Drift	Typ. 50 ppm (Max. 150ppm)
Offset Drift	Typ. 1.5 mV/K (Max. 4 mV/K)
Gain Linearity	-
Input Coupling	DC
Input Impedance	10 MΩ
Protection class	CAT IV 600 V, CAT III 1000 V
Overvoltage Protection	+-2 kVpeak
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Additional specifications
Input connector	4 mm safety banana jack
Power
Power Supply	9 - 48 V DC
Power consumption	1 W (typ.)
Environmental
IP rating	IP65 / IP67 (see 1)
Physical
Dimensions	62 x 56 x 36 mm
Weight	300 g
1) Depending on the mating connector types
Rev: 1578868200

Specifikationer för KRYPTONi-1xTH-HV

Inputs
Input types	Thermocouple
Number of channels	1
ADC Type	24-bit delta-sigma
Sampling Rate	Simultaneous 100 S/s
Input Impedance	100 MΩ
Thermocouple
TC type	Type K
Accuracy	±0.02 % of reading ±0.5 °C ±10 μV
Resolution	< 0.001 °C
Sampling rates	100, 80, 40, 20, 10 S/s
Typical Noise	0.007°C RMS @ Type K @ 10 S/sec
Additional specifications
Input connector	K-type Thermocouple LEMO REDEL 2P series
Isolation voltage	CAT III 600 V, CAT II 1000 V
Power
Power Supply	9 - 48 V DC
Power consumption	1.3 W (typ.)
Physical
Dimensions	62 x 56 x 36 mm
Weight	300 g
Rev: 1578868200

Specifikationer för KRYPTON-1xCNT

Counter
Input type	Digital
Number of channels	1
Timebase	100 MHz
Time base accuracy	Typical: 5 ppm, Max: 20 ppm
Max. bandwidth	10 MHz
Input Filter	500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level Compatibility	TTL (Low: < 0.8 V, High > 2 V)
Input impedance	100 kΩ pull-up to +3.3 V
Input Protection	±25 V continuous
Isolated Sensor Power Supply
Output Voltage +5 V	5 V +/- 10 % 100 mA max.
Output Voltage +12 V	12 V +/-10 % 90 mA max.
Additional specifications
Input connector	LEMO 1T series 7-pin
Isolation	-
Power
Power Supply	9 - 48 V DC
Power consumption	1.2 W (typ.)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
Rev: 1578868200

Specifikationer för KRYPTON-1xAO

Analog Output
Output types	Voltage
Number of channels	1
DAC Resolution	18 bit
Function	File replay, conditioned AI output, FGEN (software option), channel output
Update Rate	20 kS/s (5 kS/s with 3rd party master)
Analogue out bandwidth	4 kHz
Full Scale Output Range	±10 V
Accuracy (typ.)	0.1 % ±1 mV (0 to 20 mA load)
Temperature gain drift (typ.)	±10 ppm/K
Temperature offset drift (typ.)	±5 uV/K
SNR @ 1000 S/s output rate	92 dB (sine wave, 250 Hz, ±9 V)
THD	-90 dB
Output impedance	0.45 Ω DC
Maximum output current	20 mA
Settling time (0.05 % of set value)	30 μs @ 1000 Ω load, -10 V to 10 V step
Max slew rate	2.5 V/μs @ 1000 Ω load
Max capacitive load (2 % overshoot)	10 nF
Maximum load	500 Ω
Output protection	Short circuit protected
Additional specifications
Output connector	BNC
Power
Power supply	9 - 48 V DC
Power consumption	2 W (typ.)
Environmental
IP rating	IP65 / IP67 (see 1)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
1) Depending on the mating connector types
Rev: 1714120668

Specifikationer för KRYPTONi-4xDI

Digital Inputs
Input type	Digital
Number of channels	4
Compatibility	TTL / CMOS Voltage Levels
Input low level	UIN < 1 V
Input high level	UIN > 2 V
Input high current @ 5 V UIN	3 mA typ.
Input high current @ 30 V UIN	6 mA typ.
Propagation delay	< 1 μs
Max. sampling rate	40 kS/s
Non-Isolated Sensor Power Supply
Output Voltage +5 V	5 V +/- 10 % 300 mA max. (see 1)
Output Voltage +12 V	12 V +/-10 % 100 mA max. (see 1)
Output Voltage +Vecat	EtherCAT Bus Supply Voltage 200 mA max. (see 1)
Additional specifications
Connector	DSUB15HD Male
Overvoltage protection	30 V Continuous, 65 V peak
Isolation	Galvanic isolation CH, GND
Power
Power supply	9 - 48 V DC
Power consumption	1.5 W (typ.)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200

Specifikationer för KRYPTONi-4xDO

Digital Outputs
Output type	Digital
Number of channels	4
Maximum update rate	depends on EtherCAT master cycle time
Output type	open collector with active internal pullup to 5 V
Sink	max 50 V, 2 A (resistive load, unprotected)
Source	5 V, max. 40 mA (internally limited)
Max. switching frequency for internal PWM	100 kHz
Non-Isolated Sensor Power Supply
Output Voltage +5 V	5 V +/- 10 % 300 mA max. (see 1)
Output Voltage +12 V	12 V +/-10 % 100 mA max. (see 1)
Output Voltage +Vecat	EtherCAT Bus Supply Voltage 200 mA max. (see 1)
Additional specifications
Connector	DSUB15HD Female
Isolation	Galvanic isolation CH, GND
Power
Power supply	9 - 48 V DC
Power consumption	2 W (typ.)
Physical
Dimensions	62 x 56 x 29 mm
Weight	250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200

Tekniska specifikationer för KRYPTONi-1xCAN

	KRYPTONi-1xCAN
CAN ports specification
Number of ports	1
Interface type	CAN 2.0B
Interface data rate	up to 1 Mbit/sec
Special protocols	J1939 (see 1)
Galvanic isolation	Isolated
Bus pin fault protection
Power specification
Power supply	9 - 50 V DC
Maximum sensor power consumption	5 V / max. 250 mA (1.25 W) 12 V / max. 90 mA (1.1 W)
Maximum power consumption
Environmental specification
Interface	EtherCAT, 100 Mbit/s Lemo 1T (1 cable for data, power and sync, daisy chainable)
Connector type	DSUB-9
Physical dimensions	62 x 56 x 29 mm
Weight	200 g 0.44 lbs
Operating temperature	-40 °C to +85 °C
Storage temperature	-40 °C to +85 °C
Humidity	-
IP protection	IP65 / IP67
1) Transmit mode not supported yet. OBDII and XCP plugins not supported yet.
Rev.: 1671516000

Tekniska specifikationer för KRYPTONi-1xCAN-FD

	KRYPTONi-1xCAN-FD
CAN ports specification
Number of ports	1
Interface type	CAN-FD, CAN 2.0B (See 1)
Interface data rate	up to 5 Mbit/sec
Special protocols	J1939
Galvanic isolation (Sensor supply not isolated)	Isolated
Bus pin fault protection	±28 V
Power specification
Power supply	9 - 50 V DC
Maximum sensor power consumption	max. 1.4 W (5 V / 12 V) (max. 1.2 W on 12 V)
Maximum power consumption	max. 2 W (no load)
Environmental specification
Interface	EtherCAT, 100 Mbit/s Lemo 1T (1 cable for data, power and sync, daisy chainable)
Connector type	DSUB-9
Physical dimensions	62 x 56 x 29 mm
Weight	200 g 0.44 lbs
Operating temperature	-40 °C to +85 °C
Storage temperature	-40 °C to +85 °C
IP protection	IP65 / IP67
1) Transmit mode not supported. OBDII and XCP plugins not supported yet.

Specifikationer för KRYPTON-8xACC

Analog inputs	KRYPTON-8xACC
Input type	Voltage, IEPE
Number of channels	8
ADC Type	24-bit delta-sigma with anti-aliasing filter
Sampling Rate	Simultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges	±10 V	±5 V	±1 V	±200 mV
Input Accuracy	±0.03 % of reading ±0.02 % of range ±0.2 mV
Typical Dynamic Range @ 10 kS/s	-140 dB	-137 dB	138 dB	-134 dB
Typical noise floor @ 10 kS/s	-106 dB	-106 dB	106 dB	-102 dB
Type. THD (20 kS/s, -1 dBFS sine wave @ 1 kHz)	-94 dB	-94 dB	-93 dB	-95 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	96 dB	96 dB	96 dB	93 dB
Gain Drift	Typical 10 ppm/K, max. 20 ppm/K
Offset Drift	Typical 0.5 μV/K + 1 ppm of range/K, max 2 μV/K + 3 ppm of range/K
Input Coupling	DC, AC 0.1 Hz, 1 Hz
Input Impedance	1 MΩ
Overvoltage Protection	In+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
IEPE input
Excitation	4 mA, 8 mA
Compliance voltage	25 V
Output Impedance	>100 kΩ
Sensor detection	Shortcut: <4 V; Open: >19 V
Additional Specifications
Input connector	BNC
TEDs support	IEPE mode only
Power
Power Supply	9 - 48 V DC
Power Consumption	4.6 W
Environemental
IP rating (see 1)	IP67
Physical
Weight	1000 g
Slice Dimensions	213 x 54 x 56 mm
Dimensions with Connectors	213 x 54 x 66.8 mm
1) Depending on the mating connector types
Rev: 1703235600

Specifikationer för KRYPTON-4xACC

Analog inputs	KRYPTON-4xACC
Input type	Voltage, IEPE
Number of channels	4
ADC Type	24-bit delta-sigma with anti-aliasing filter
Sampling Rate	Simultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges	±10 V	±5 V	±1 V	±200 mV
Input Accuracy	±0.03 % of reading ±0.02 % of range ±0.2 mV
Typical Dynamic Range @ 10 kS/s	-140 dB	-137 dB	138 dB	-134 dB
Typical noise floor @ 10 kS/s	-106 dB	-106 dB	106 dB	-102 dB
Type. THD (20 kS/s, -1 dBFS sine wave @ 1 kHz)	-94 dB	-94 dB	-93 dB	-95 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	96 dB	96 dB	96 dB	93 dB
Gain Drift	Typical 10 ppm/K, max. 20 ppm/K
Offset Drift	Typical 0.5 μV/K + 1 ppm of range/K, max 2 μV/K + 3 ppm of range/K
Input Coupling	DC, AC 0.1 Hz, 1 Hz
Input Impedance	1 MΩ
Overvoltage Protection	In+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
IEPE input
Excitation	4 mA, 8 mA
Compliance voltage	25 V
Output Impedance	>100 kΩ
Sensor detection	Shortcut: <4 V; Open: >19 V
Additional Specifications
Input connector	BNC
TEDs support	IEPE mode only
Power
Power Supply	9 - 48 V DC
Power Consumption	3 W
Environemental
IP rating (see 1)	IP67
Physical
Weight	700 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 66.8 mm
1) Depending on the mating connector types
Rev: 1703235600

Specifikationer för KRYPTON-3xSTG

Analog inputs	KRYPTON-3xSTG
Input type	Voltage Full / half / quarter strain
Number of channels	3
ADC Type	24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rate	Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges	±10 V	±1 V	±100 mV	±10 mV
Input Accuracy	±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS/s	-139 dB	-139 dB	-129 dB	-110 dB
Typical Noise Floor @ 10 kS/s	-106 dB	-105dB	-97 dB	-78 dB
Typical CMR @ 400 Hz / 1 kHz	86 dB / 84 dB	96 dB / 95 dB	112 dB / 102 dB	112 dB / 102 dB
Gain Drift	Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift	Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity	< 0.02 %
Input Coupling	DC
Input Impedance	10 MΩ
Overvoltage Protection	In+ to In-: 50 V continuous, 200 V peak (10 ms)
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Excitation Voltage
Excitation voltage	Free programmable (16-bit DAC)
Predefined Levels	0, 1, 2.5, 5, 10 and 15 VDC
Accuracy	±0.05 % ±2 mV
Drift	±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load	< 0.01 %
Current Limit	45 mA (400 mW max. Power)
Protection	Continuous short to ground
Bridge mode
Bridge Connection Types	full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Ranges	2…1000 mV/V free programmable
Internal Bridge Completion	½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy	0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor	100 kΩ (others on request)
Shunt Resistor Accuracy	0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust	Software-selectable
Additional Specifications
Input connector	DB9; L1T7f; L2B10f
TEDs support	Standard + DSI adapters
Power
Power Consumption	3.5 W (4.8 W 120 Ω @ 5 V load)
Power Supply	9 - 48 V DC
Environmental
IP rating	IP67
Physical
Weight	740 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 58.2 mm

Specifikationer för KRYPTON-6xSTG

Analog inputs	KRYPTON-6xSTG
Input type	Voltage Full / half / quarter strain
Number of channels	6
ADC Type	24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rate	Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges	±10 V	±1 V	±100 mV	±10 mV
Input Accuracy	±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS/s	-139 dB	-139 dB	-129 dB	-110 dB
Typical Noise Floor @ 10 kS/s	-106 dB	-105dB	-97 dB	-78 dB
Typical CMR @ 400 Hz / 1 kHz	86 dB / 84 dB	96 dB / 95 dB	112 dB / 102 dB	112 dB / 102 dB
Gain Drift	Typical 10 ppm/K (max. 40 ppm/K)
Offset Drift	Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity	< 0.02 %
Input Coupling	DC
Input Impedance	10 MΩ
Overvoltage Protection	In+ to In-: 50 V continuous, 200 V peak (10 ms)
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Excitation Voltage
Excitation voltage	Free programmable (16-bit DAC)
Predefined Levels	0, 1, 2.5, 5, 10 and 15 VDC
Accuracy	±0.05 % ±2 mV
Drift	±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load	< 0.01 %
Current Limit	45 mA (400 mW max. Power)
Protection	Continuous short to ground
Bridge mode
Bridge Connection Types	full bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Ranges	2…1000 mV/V free programmable
Internal Bridge Completion	½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy	0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor	100 kΩ (others on request)
Shunt Resistor Accuracy	0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust	Software-selectable
Additional Specifications
Input connector	DB9; L1T7f; L2B10f
TEDs support	Standard + DSI adapters
Power
Power Consumption	5.9 W (8.9 W load 120 Ω @ 5 V)
Power Supply	9 - 48 V DC
Environmental
IP rating	IP67
Physical
Weight	1100 g
Slice Dimensions	213 x 54 x 56 mm
Dimensions with Connectors	213 x 54 x 58.2 mm

Specifikationer för KRYPTONi-4xLV

Analog input	KRYPTONi-4xLV
Input type	Isolated voltage
Number of channels	4
ADC Type	24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rates	Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Range	±50 V
Accuracy	±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	104 dB
Typical noise floor @ 10 kS/s	-106 dB
Type. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)	-104 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	105 dB
Typical CMR @ 400 Hz / 1 kHz	105 dB / 94 dB
Gain Drift	Typical 10 ppm/K, max. 20 ppm/K
Offset Drift	Typical 5 μV/K, max. 10 μV/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	1 MΩ
Noise	0.7 mVRMS
Overvoltage Protection	In+ to In-: 200 V continuous, 350 Vpeak (100 msec)
Analog input performance
Bandwidth (-3dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Additional Specifications
Input Connector	BNC
Isolation Voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power Consumption	3.8 W
Environmental
IP Rating (see 1)	IP67
Physical
Weight	700 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 66.8 mm
1) Depending on the mating connector types

Specifikationer för KRYPTONi-8xLV

Analog input	KRYPTONi-8xLV
Input type	Isolated voltage
Number of channels	8
ADC Type	24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rates	Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Range	±50 V, ±100 V (see 2)
Accuracy	±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	104 dB
Typical noise floor @ 10 kS/s	-106 dB
Type. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)	-104 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)	105 dB
Typical CMR @ 400 Hz / 1 kHz	105 dB / 94 dB
Gain Drift	Typical 10 ppm/K, max. 20 ppm/K
Offset Drift	Typical 5 μV/K, max. 10 μV/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	1 MΩ
Noise	0.7 mVRMS
Overvoltage Protection	In+ to In-: 200 V continuous, 350 Vpeak (100 msec)
Analog input performance
Bandwidth (-3dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Additional Specifications
Input Connector	BNC, Lemo 2 pin (see 2)
Isolation Voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power Consumption	6.8 W
Environmental
IP Rating (see 1)	IP67
Physical
Weight	1000 g
Slice Dimensions	213 x 54 x 56 mm
Dimensions with Connectors	213 x 54 x 66.8 mm
1) Depending on the mating connector types
2) Upon request

KRYPTONi-8xLA specifications

Analog input	KRYPTONi-8xLA
Input type	Isolated current
Number of channels	8
ADC Type	24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling Rates	Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Current Mode
Range	±20 mA
Accuracy	±0.02 % of reading ±8 µA
Typical noise floor @ 10 kS/s	-95 dB
Crosstalk (20 kS/s, -1 dBFS @ 1 kHz)	-124 dB
Gain Drift	Typical 10 ppm/K, max. 20 ppm/K
Offset Drift	Typical 100 nA/K, max. 200 nA/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	50 Ω
Noise	0.3 µARMS
Overvoltage Protection	50 V
Analog input performance
Bandwidth (-3 dB)	0.49 fs
Alias-free Bandwidth	DC to 0.453 fs
Alias Rejection	-100 dB (all sample rates)
Delay Through ADC	37 / fs
Oversampling	32
Additional Specifications
Input Connector	BNC
Isolation Voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power Consumption	6.8 W
Environmental
IP Rating (see 1)	IP67
Physical
Weight	1000 g
Slice Dimensions	213 x 54 x 56 mm
Dimensions with Connectors	213 x 54 x 66.8 mm
1) Depending on the mating connector types

Specifikationer för KRYPTONi-8xTH

Analog inputs	KRYPTONi-8xTH
Input type	Isolated universal thermocouple and voltage
Number of channels	8
ADC Type	24-bit delta-sigma
Sampling rates	Simultaneous 100, 80, 40, 20, 10 S/s (software selectable)
Voltage Ranges
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±100 μV	±0.02 % of reading ±10 μV
Typical Noise Floor @ 10 / 100 S/s	-114 dB / -105 dB	-109 dB / -100 dB
Gain Drift	Typical 3 ppm/K (max. 10 ppm/K)
Offset Drift	0.03 μV/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	100 MΩ
Thermocouple
Input type	TC Types: K, J, T, R, S, N , E, C, B
Accuracy	±0.02 % of reading ± 0.5 °C ± 10 μV
Typical Noise	0.007 °C RMS @ Type K @ 10 S/s
Additional Specifications
Input connector	Mini Thermocouple connector (copper)
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power supply	9 - 48 V DC
Power consumption	2.5 W
Environmental
IP rating (see 1)	IP67
Physical
Weight	720 g
Dimensions	213 x 39 x 56 mm
1) Depending on the mating connector types, for non corrosive liquids only, IP65 standard

Specifikationer för KRYPTONi-16xTH

Analog inputs	KRYPTONi-16xTH
Input type	Isolated universal thermocouple and voltage
Number of channels	16
ADC Type	24-bit delta-sigma
Sampling rates	Simultaneous 100, 80, 40, 20, 10 S/s (software selectable)
Voltage Mode
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±100 μV	±0.02 % of reading ±10 μV
Typical Noise Floor @ 10 / 100 S/s	-114 dB / -105 dB	-109 dB / -100 dB
Gain Drift	Typical 3 ppm/K (max. 10 ppm/K)
Offset Drift	0.03 μV/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	100 MΩ
Thermocouple
Input type	TC Types: K, J, T, R, S, N , E, C, B
Accuracy	±0.02 % of reading ± 0.5 °C ± 10 μV
Typical Noise	0.02 °C RMS @ Type K @ 100 S/s
Additional Specifications
Input connector	Mini Thermocouple connector (copper)
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power supply	9 - 48 V DC
Power consumption	4 W
Environmental
IP rating (see 1)	IP67
Physical
Weight	1000 g
Dimensions	213 x 54 x 56 mm
1) Depending on the mating connector types, for non corrosive liquids only, IP65 standard

KRYPTON TH noggrannhet

Temperature	Type K	Type J	Type T	Type R	Type S	Type N	Type E	Type B	Type C
-200 °C	1.19 °C	1.00 °C	1.17 °C	✗	✗	1.54 °C	0.83 °C	✗	✗
-100 °C	0.85 °C	0.76 °C	0.87 °C	✗	✗	1.00 °C	0.74 °C	✗	✗
0 °C	0.75 °C	0.70 °C	0.76 °C	2.38 °C	2.34 °C	0.89 °C	0.67 °C	✗	1.27 °C
100 °C	0.76 °C	0.70 °C	0.73 °C	1.85 °C	1.88 °C	0.86 °C	0.67 °C	10.96 °C	1.15 °C
400 °C	0.82 °C	0.76 °C	0.74 °C	1.54 °C	1.63 °C	0.85 °C	0.71 °C	3.03 °C	1.11 °C
700 °C	0.88 °C	0.80 °C	✗	1.49 °C	1.59 °C	0.89 °C	0.77 °C	2.11 °C	1.17 °C
1000 °C	0.96 °C	0.87 °C	✗	1.46 °C	1.57 °C	0.96 °C	0.85 °C	1.80 °C	1.23 °C
1300 °C	1.05 °C	✗	✗	1.47 °C	1.59 °C	1.04 °C	✗	1.68 °C	1.35 °C
1700 °C	✗	✗	✗	1.58 °C	1.71 °C	✗	✗	1.70 °C	1.65 °C

Specifikationer för KRYPTONi-16xTH-HS

Analog inputs	KRYPTONi-16xTH-HS
Input type
Number of channels	16
ADC Type	24-bit delta-sigma
Sampling rates	Simultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Voltage Mode
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±50 μV	±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s	-130 dB / -120 dB / -110 dB / -104 dB	-120 dB / -110 dB / -100 dB / -90 dB
Offset Drift	Typ. 0.05 μV/K (Max. 0.2 μV/K)	Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain Drift	Typ. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity	< 0.007 %
Input Coupling	DC
Input Impedance	100 MΩ
Thermocouple
Input type	TC Types: K, J, T, R, S, N , E, C, B
Accuracy	±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise	0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
Input connector	Mini Thermocouple connector (copper)
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power consumption	Typ. 4.3 W (Max. 5 W)
Environmental
IP rating	IP67
Physical
Weight	1060 g
Dimensions	213 x 54 x 56 mm
Rev: 1660298400

Specifikationer för KRYPTONi-8xTH-HS

Analog inputs	KRYPTONi-8xTH-HS
Input type	Isolated universal thermocouple and voltage
Number of channels	8
ADC Type	24-bit delta-sigma
Sampling rates	Simultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Voltage Mode
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±50 μV	±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s	-130 dB / -120 dB / -110 dB / -104 dB	-120 dB / -110 dB / -100 dB / -90 dB
Offset Drift	Typ. 0.05 μV/K (Max. 0.2 μV/K)	Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain Drift	Typ. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity	< 0.007 %
Input Coupling	DC
Input Impedance	100 MΩ
Thermocouple
Input type	TC Types: K, J, T, R, S, N , E, C, B
Accuracy	±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise	0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
Input connector	Mini Thermocouple connector (copper)
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power consumption	Typ. 2.6 W (Max. 3 W)
Environmental
IP rating	IP67
Physical
Weight	750 g
Dimensions	213 x 39 x 56 mm
Rev: 1660298400

KRYPTON TH-HS noggrannhet

Temperature	Type K	Type J	Type T	Type R	Type S	Type N	Type E	Type B	Type C
-200 °C	1.00 °C	0.86 °C	0.98 °C	✗	✗	1.24 °C	0.71 °C	✗	✗
-100 °C	0.75 °C	0.69 °C	0.77 °C	✗	✗	0.85 °C	0.67 °C	✗	✗
0 °C	0.68 °C	0.64 °C	0.68 °C	1.82 °C	1.79 °C	0.77 °C	0.62 °C	✗	1.07 °C
100 °C	0.69 °C	0.65 °C	0.67 °C	1.46 °C	1.47 °C	0.76 °C	0.62 °C	7.96 °C	0.96 °C
400 °C	0.75 °C	0.71 °C	0.72 °C	1.26 °C	1.31 °C	0.77 °C	0.67 °C	2.30 °C	0.95 °C
700 °C	0.81 °C	0.75 °C	✗	1.23 °C	1.30 °C	0.82 °C	0.73 °C	1.67 °C	1.01 °C
1000 °C	0.88 °C	0.82 °C	✗	1.23 °C	1.31 °C	0.88 °C	0.83 °C	1.47 °C	1.07 °C
1300 °C	0.96 °C	✗	✗	1.26 °C	1.34 °C	0.98 °C	✗	1.40 °C	1.17 °C
1700 °C	✗	✗	✗	1.36 °C	1.45 °C	✗	✗	1.45 °C	1.34 °C

Specifikationer för KRYPTONi-8xRTD

Analog inputs	KRYPTONi-8xRTD
Input types	voltage, resistor or universal Ptxxx inputs
Number of channels	8
ADC Type	24-bit delta-sigma
Sampling Rate	Simultaneous 100 S/s
Voltage Mode
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±0.01 % of range ±10 μV	±0.02% of reading ±0.01% of range ±10 μV
Typical Noise floor @ 10/100 S/s	-108 dB / -98 dB	-108 dB / -98 dB
Gain Drift	Typical 3 ppm/K (max. 10 ppm/K)
Offset Drift	Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	1 MΩ
Temperature Mode
Ranges	PT500, PT1000, PT2000	PT100, PT200
Measurement range	-200 °C to +850 °C
Accuracy	±0.05 % of reading ±0.2 °C
Temperature Drift	typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection	3 wire or 4 wire
Resistance mode
Ranges	0…10 kΩ	0…1 kΩ
Accuracy	±0.02 % of reading ±0.01 % of range
Input Connection	3 wire or 4 wire
Additional Specifications
Input connector	Lemo 0B 6pin EEA.0B.306.CLN
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power consumption	2.5 W
Environmental
IP rating (see 1)	IP65
Physical
Weight	720 g
Dimensions	213 x 39 x 58 mm
1) Depending on the mating connector types
Rev: 1564584000

Specifikationer för KRYPTONi 8xRTD-HS

Analog inputs	KRYPTONi-8xRTD-HS
Input types	Voltage, Resistance or Universal PTxxx inputs
Number of channels	8
ADC Type	24-bit delta-sigma
Sampling Rate IOLITE	Simultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN	100 S/s
Voltage Mode
Ranges	±1 V	±100 mV
Input Accuracy	±0.02 % of reading ±0.01 % of range
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s	-130 dB / -120 dB / -110 dB / -104 dB	-120 dB / -108 dB / -98 dB / -90 dB
Offset Drift	Typ. 0.05 μV/K (Max. 0.2 μV/K)	Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain Drift	Typ. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity	< 0.007 %
Input Coupling	DC
Input Impedance	10 MΩ
Temperature
Ranges	PT500, PT1000, PT2000	PT100, PT200
Excitation current	150 uA	400 uA
Measurement range	-200 °C to +850 °C
Accuracy	±0.02 % of reading ±0.2 °C
Temperature Drift	Typ. ±2 ppm/K (Max. ±10 ppm/K)
Input Connection	3-wire or 4-wire
Resistance Mode
Ranges	0…10 kΩ	0…1 kΩ
Excitation current	150 uA	400 uA
Accuracy	±0.02 % of reading ±0.008 % of range
Input Connection	3-wire or 4-wire
Additional Specifications
Input connector	Lemo 0B 6pin EEA.0B.306.CLN
Isolation voltage	1000 Vpeak channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power consumption	Typ. 3.5 W (Max. 4.7 W)
Environmental
IP rating (see 1)	IP65
Physical
Weight	755 g
Dimensions	213 x 39 x 58 mm
1) Depending on the mating connector types
Rev: 1564584000

Specifikationer för KRYPTON-4xCNT

Digital inputs
Input type	Digital
Number of channels	4
Input connector	LEMO 1T series 7-pin
Timebase	100 MHz
Time base accuracy	Typical: 5 ppm, Max: 20 ppm
Max. bandwidth	10 MHz
Input Filter	500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level Compatibility	TTL (Low: < 0.8 V, High > 2 V)
Input impedance	100 kΩ pull-up to +3.3 V
Input Protection	±25 V continuous
Isolation	Ch to GND isolation
Isolated Sensor Power Supply
Output Voltage +5 V	5.1 V +/- 10 % 100 mA max. (400 mA to supply 4 channels)
Output Voltage +12 V	12.1 V +/-5 % 50 mA max. (200 mA to supply 4 channels)
Isolation	Ch to GND isolation
Power
Power Supply	9 - 48 V DC
Power consumption	Typ 2.3 W (Max 2.7 W)
Physical
Dimensions	213 x 39 x 56 mm
Weight	700 g
Rev: 1709799612

Specifikationer för KRYPTONi-8xDI-8xDO

	KRYPTONi-8xDI-8xDO
Digital Input
Isolated Input Channels	8
Compatibility	CMOS Configuration
Input low level	UIN < 0.8 V
Input high level	UIN > 2.4 V
Input high current @ 5 V	IIN < 1.8 mA
Input high current @ 30 V	IIN < 6 mA
Propagation delay	< 1 μs
Sampling rate	Simultaneous 40 kS/s
Overvoltage protection	40 V continuous (65 V peak)
Isolation voltage peak	250 V channel/ground & channel/channel
Digital Output
Isolated Output Channels	8
Compatibility	Open collector with 10 kΩ pull-up to +5 V
Maximum sink current	150 mA (not protected)
Maximum switching voltage	50 V
Propagation delay	< 20 μs
Maximum update rate	depending on EtherCAT master
Isolation voltage peak	250 V channel to ground, no channel to channel isolation
Power
Power Supply	9 - 48 V DC
Power consumption	2 W
Environmental
IP rating	IP67
Physical
Weight	700 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 58.2 mm
Rev: 1602590400

Specifikationer för KRYPTONi-16xDO

	KRYPTONi-16xDO
Digital Output
Isolated Output Channels	16
Compatibility	Open collector with 10 kΩ pull-up to +5 V
Maximum sink current	150 mA (not protected)
Maximum switching voltage	50 V
Propagation delay	< 20 μs
Maximum update rate	depending on EtherCAT master
Isolation voltage peak	250 V channel to ground, no channel to channel isolation
Power
Power Supply	9 - 48 V DC
Power consumption	2 W
Environmental
IP rating	IP67
Physical
Weight	700 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 58.2 mm
Rev: 1602590400

Specifikationer för KRYPTONi-16xDI

	KRYPTONi-16xDI
Digital Input
Isolated Input Channels	16
Compatibility	CMOS Configuration
Input low level	UIN < 0.8 V
Input high level	UIN > 2.4 V
Input high current @ 5 V	IIN < 1.8 mA
Input high current @ 30 V	IIN < 6 mA
Propagation delay	< 1 μs
Sampling rate	Simultaneous 40 kS/s
Overvoltage protection	40 V continuous (65 V peak)
Isolation voltage peak	250 V channel/ground & channel/channel
Power
Power Supply	9 - 48 V DC
Power consumption	2 W
Environmental
IP rating	IP67
Physical
Weight	700 g
Slice Dimensions	213 x 39 x 56 mm
Dimensions with Connectors	213 x 39 x 58.2 mm
Rev: 1602590400

Zurück zum Anfang