| Number of channels | 8 | | | |
| Inputs | Voltage, full bridge | | | |
| ADC type | 24-bit sigma-delta with anti-aliasing filter | | | |
| Sampling rate | Simultaneous 200 kS/sec | | | |
| Input type | Differential | | | |
| Voltage Mode |
| Ranges | ±10 V | ±1 V | ±100 mV | ±10 mV |
| DC accuracy | 0.05 % of value + 1 mV | 0.05 % of value + 0.2 mV | 0.05 % of value + 0.1 mV | 0.05 % of value + 0.1 mV |
| CMRR@ 50Hz/400Hz/1kHz | 85 dB / 92 dB / 89 dB | 97 dB / 97 dB / 88 dB | 100 dB / 97 dB / 89 dB | 101 dB / 97 dB / 89 dB |
| Noise floor | 107 dB @ ±10 V range | | | |
| Signal to noise:
0.1 kS/s to 51.2 kS/s
51.2 kS/s to 102.4 kS/s
102.4 kS/s to 200 kS/s |
105 dB
100 dB
75 dB | | | |
| Gain Drift | Typical 10 ppm/K, max. 40 ppm/K | | | |
| Offset Drift | Typical 2 μV/K + 5 ppm of range/K, max 5 μV/K + 10 ppm of range/K | | | |
| Channel-to-Channel Phase Mismatch | <0.1° @ 5 kHz | | | |
| Phase-to-Phase Mismatch | 0.6° @ 1 kHz | | | |
| Input impedance | 20 MΩ
| 47 pF (differential)
10 MΩ || 33 pF (common mode) | | | |
| Maximum common mode voltage | ±13 V | | | |
| Overvoltage protection | ±70 V input protection | | | |
| Excitation Voltage |
| Excitation voltage | ±5 V ±0.1 % bridge sensor supply, 70 mA limit | | | |
| Excitation Drift | ±50 ppm/K ±100 μV/K | | | |
| Sensor supply | 12 V, 350 mA (Shared between: 8xAI, 8xCounters, 2xCAN) | | | |
| Counter/Digital inputs |
| Number of channels | 8 counters/24 digital input, fully synchronized with analog | | | |
| Modes | Counting, waveform timing, encoder, tacho, geartooth sensor | | | |
| Counter timebase | 102.4 MHz | | | |
| Time base accuracy | Typical: 5 ppm, Max: 20 ppm | | | |
| Max. Bandwidth | 10 MHz | | | |
| Input Filter | 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs | | | |
| Counter resolution | 32-bit | | | |
| Input Compatibility, Level | TTL/CMOS (Low: <0.8 V, High >2 V) | | | |
| Input termination, impedance | 100 kΩ pull-up to +3.3 V | | | |
| Input Protection | ±30 V continuous | | | |
| Alarm output | Not available | | | |
| Sensor supply | +5 V, +12 V (See bellow: Power, Sensor power supply) | | | |
| CAN bus |
| Number of ports | 2 | | | |
| Interface type | CAN 2.0B, up to 1 MBit/sec | | | |
| Special applications | CCP, OBDII, J1939, CAN output | | | |
| Galvanic isolation | Isolated | | | |
| Bus pin fault protection | ±36 V | | | |
| ESD protection | 8 kV | | | |
| Interfaces and options |
| USB | USB-B mini, USB 2.0 interface | | | |
| Synchronisation | 2x SIRIUS® SYNC | | | |
| Max. Sync-cable length | 100 m (Master/Slave), 200 m (IRIG) | | | |
| Power |
| Power supply | 9 - 36 V DC | | | |
| Galvanic isolation | ISO-POWER Isolated | | | |
| Sensor power supply | Up to 10W total:
12 V, total limit 350 mA (Shared between: 8xAI, 8xCounters, 2xCAN)
5 V, total limit 700 mA (Shared between: 8xCounters, 2xCAN)
+/-5 V Exc., Ch. limit 70 mA | | | |
| Power consumption | Typ. 6 W, Max. 18 W | | | |
| Environmental |
| Operating Temperature | Max. 60 °C down to -20 °C | | | |
| Storage Temperature | -40 °C to 85 °C | | | |
| Humidity | 5 to 95 % RH non-condensing at 50 °C | | | |
| IP rating | IP50 | | | |
| Shock & Vibration | Vibration sweep sinus (EN 60068-2-6:2008)
Vibration random (EN 60721-3-2: 1997 - Class 2M2)
Shock (EN 60068-2-27:2009)
MIL-STD-810D | | | |
| Physical |
| Dimensions | 225 x 80 x 45 mm | | | |
| Weight | 0.72 kg | | | |
| Rev: 1628236800 |
