| Type | Zero-Flux | | |
| Primary Current Range DC (max) | 1000 A | | |
| Primary Current Range AC rms (max) | 700 A | | |
| Conversion ratio | 1:1680 | | |
| DC Accuracy |
| Nominal Burden Resistance | 1 Ω (max. 3 Ω) | | |
| Transformer/Gain Off-Center Error | 10ppm (max. <30ppm) | | |
| Temperature influence (typ.) | 3 ppm/K | | |
| Nominal secondary current | ~595.2 mA @ 1000 A | | |
| Bandwidth ( -3 dB) (typ.) | DC ... 500 kHz | | |
| Gain Linearity @1000 A range | Typ. 83 ppm (max. <100ppm) | | |
| Offset including hysteresis | Typ. 65 mA (max. 100 mA) | | |
| AC Accuracy |
| Frequency Bandwidth @ -0.5 dB, IP = 0.8 ARMS | 500 kHz | | |
| Frequency Bandwidth @ -3 dB, IP = 0.7 ARMS | 750 kHz | | |
| Noise (ppm rms) | Min [mA] | Typ [mA] | Max [mA] |
| 0 - 10000 Hz | 0.4 | 0.6 | 1.3 |
| 0 - 100000 Hz | 0.8 | 1.2 | 2 |
| 0 - 1000000 Hz | 5.4 | 5.5 | 6.5 |
| Platiše Flux Sensor Frequency (seen as ripple) | 220 kHz | | |
| D-Class Switching Frequency (seen as ripple) | 750 kHz | | |
| Other |
| Time to Out of Range Detection (Status Deasserted) | 300 µs
| | |
| Primary to Secondary Maximum Difference RTI | ±1500 mA | | |
| Status Open Collector Max Current | Typ. 25 mA (Max. 50 mA) | | |
| Status Open Collector Max Voltage | Typ. 60 V (Min. -5 V, Max. 80 V) | | |
| Immunity to external magnetic field, 5 mT in any direction RTI | Typ. ±30 mA (Max. < 50 mA) | | |
| Induced RMS voltage on primary conductor at IP = 0 | 32 µV | | |
| Induced RMS voltage on primary conductor during Search | 1223 µV | | |
| Power Supply |
| Min | Typ | Max |
| Power Supply Voltage between pin 9 and 5 | 24 V | 30 V | 35 V |
| 500 A Range Power Supply Voltage | 12 V | 30 V | 35 V |
| Power Supply Max. In-rush/working current @ 30 V | < 0.5 A | | |
| Standby (Idle) Power Consumption | Typ. 0.56 W (Max. 0.7 W) | | |
| Power Consumption | 3 W @IP = 500 A and Burden 3 Ω
6.6 W (max. 8 W) @IP = 1000 A and Burden 1 Ω
7.6 W (max. 9 W) @IP = 1000 A and Burden 3 Ω | | |
| Environmental |
| Operating temperature | -40 °C to +85 °C | | |
| Non-insulated wire
Isolation CAT II / CAT III
IEC 61010-1 standards, EN 50178 standards | 1000 V CAT II
600 V CAT III | | |
| Insulated wire
Isolation CAT II / CAT III
IEC 61010-1 standards, EN 50178 standards | 1000 V CAT II
1000 V CAT III | | |
| Clearance / Creepage | 12 mm | | |
| Weight | 500 g | | |
| Inner diameter | 22 mm | | |
| Dimensions | 77 x 57 x 46.7 mm | | |
| DEWESoft® Shunt | 1 Ω | | |
| PWR-MCTS2 needed | Yes (±15 V) | | |
