La flexibilité de l'analyseur de puissance DEWESoft et la haute précision de ses mesures, sont idéaux pour les mesures d'efficacité sur les transformateurs et les calculs d'énergie.

La flexibilité de l'analyseur de puissance DEWESoft et la haute précision de ses mesures, sont idéaux pour les mesures d'efficacité sur les transformateurs et les calculs d'énergie.
Testing of power transformers makes a couple of different measurements necessary, which are described in the international IEC 60076 standard.
Scope and Vector Scope offer the capability to analyze the voltage ratio and phase displacement of different primary and secondary configurations (star, delta, interconnected star).
Transient recording functionality allows storing all signals at the full sampling rate for detailed analysis. In combination with the trigger functionality failures and transient events (also during long-term measurements of the transformer) can easily be detected.
The Power quality module allows measuring harmonics of the voltage and the current up to some hundred kHz. The data can be represented in percentage of the fundamental frequency as required for the no-load current according to IEC 60076 standard.
The power quality module also automatically calculates the zero-sequence impedance which is required in the power transformer testing.
The math library allows to automatically calculate parameters like the magnetizing current, the iron losses, the main inductance for example out of the no-load test or the stray inductances out of the short-circuit tests.
For more information check the power quality application page.
Power and efficiency analysis of the transformers require the highest accuracy of the power calculation for all phase angles. Especially analysis at lower power factors is very difficult with conventional measurement equipment.
The additional sensor calibration functionality allows correcting the behavior of voltage and current transducers for amplitude and phase over the whole frequency range.
Furthermore, IEC 60076-1 standard requires the correction of measured power losses depending on the temperature. Dewesoft power analyzer makes it easy to measure all the required temperatures (winding, oil, ambient, etc.) perfectly synchronized to voltage, current and other measured parameters.
In addition, it’s possible to automatically calculate the corrected power losses. You can also measure the power of oil pumps and fan motors, and even the sound level of the transformer according to IEC 60551 standard.
This covers all the possible tests that you can experience with power transformers, and Dewesoft can cover them all with one single device.
Analysis according to IEC 60076 standard
Correction of power losses depending on temperature
Additional software sensor calibration
Measure harmonics and symmetrical components
For the most typical configuration, we suggest R2DB DAQ system with optional additional KRYPTON DAQ for temperature inputs:
Système d'acquisition de données ultra compact et mobile avec enregistreur intégré, PC industriel de traitement des données, écran tactile et batteries internes pour une portabilité maximale.
Capteurs de haute précision pour la mesure de courant AC/DC et l'analyse de puissance. Des pinces ampèremétriques aux transducteurs de courant à flux nul de haute précision et aux bobines de Rogowsky.
Nos transducteurs de courant sont parfaitement adaptés à nos systèmes d'acquisition de données et peuvent mesurer avec précision le courant AC/DC avec une précision allant jusqu'à 0,03 %. TEDS équipé pour la détection et la configuration automatiques.
DewesoftX est un logiciel d'acquisition de données primé pour les tests, la mesure et la surveillance. Faites l'expérience de l'enregistrement de données, du traitement du signal et de la visualisation des données comme jamais auparavant.
Le logiciel DewesoftX DAQ a reçu de nombreux prix internationaux, est innovant et facile à utiliser, mais en même temps très riche en fonctionnalités. Notre mission est claire : un seul logiciel pour toutes les applications de test et de mesure.
La solution Dewesoft peut mesurer tous les paramètres de qualité d’alimentation conformément à la norme IEC 61000-4-30 Classe A. Par rapport à d’autres analyseurs de qualité d’énergie, il est possible de réaliser une analyse plus détaillée (par exemple, stockage de données brutes, comportement en cas de défaillance, calcul de paramètres supplémentaires, etc.).