KRYPTON® Spécifications techniques

KRYPTON® ONE spécifications générales

Interface
Data interfaceEtherCAT®
Data rate100Mbps Full Duplex bus speed
Sync Accuracybelow 1 sample to Sirius®
EtherCAT®Max. Cable Length 100 m
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s
Max. Number of Units64 or more (power injectors may be required)
Data Interface ConnectionLEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable
Power
Power Supply9 - 50 V DC
Power consumption1 - 3 W
Environmental
Operating Temperature-40 to 85 °C
Storage Temperature-40 to 85 °C
Humidity5 to 100 % RH
IP ratingIP65 / IP67 (see individual specifications for details)
ShockShock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total
VibrationRandom vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total
Rev: 1557765000

Spécifications générales du système KRYPTON® MULTI

Interface
Data interfaceEtherCAT®
Data Rate100 Mbps Full Duplex bus speed
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s (see 1)
Sync Accuracybelow 1 sample to Sirius®
EtherCAT®Max. Cable Length 100 m
Max. Number of Units64 or more (power injectors may be required)
Data Interface ConnectionLEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable
Additional Specifications
Power supply ground to mechanical ground (housing) resistance> 100 kΩ
Power
Power Supply9 - 48 V DC
Environmental
Operating Temperature-40 to 85°C
Storage Temperature-40 to 85°C
Humidity5 to 100 % RH
IP ratingIP65 / IP67
ShockShock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total
VibrationRandom vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total
1) It depends on the devices connected, numbers of channels, configuration, length of cables and other parameters.
Rev: 1673526968

Aperçu de l'amplificateur KRYPTON® ONE

AODIDOACCSTGLVHVTH-HVCNT
ConnectorBNCDSUB15HD MaleDSUB15HD FemaleBNCDB9BNCBanana jackK-type Thermocouple LEMO REDELLEMO T-type 7pin female
Number of channels per module144111111
Data rate per channel40 kS/s40 kS/s40 kS/s40 kS/s40 kS/s100 S/s20 kS/s
Resolution18 bitDigitalDigital24-bit24-bit24-bit24-bit24-bit100 MHz timebase 5 ppm, 20 ppm max
Bandwidth0.49 fs0.49 fs0.49 fs0.49 fs0.49 fs10 MHz
Voltage rangesDigital (Low: < 1 V, High: > 2 V)±10 V ±5 V ±1 V ±200 mV±50 V ±10 V ±1 V ± 100 mV±50 V ±10 V ±1 V ±100 mV±1000 VThermocoupleTTL (Low: <0.8 V, High > 2 V)
Input couplingDC, AC 0.1 Hz, 1 HzDC, AC 1 HzDC, AC 1 HzDC
Sensor excitation±10 VIEPE 4 mA, 8 mAUnipolar 0 - 24 V Bipolar 0 - 12 V5 V (100 mA max.), 12 V (90 mA max.)
Bridge connectionFull, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire
Programmable shunt100 kΩ
IEPE inputDSI-ACC
Resistance
Temperature (PTx)DSI-RTD
ThermocoupleDSI-THK-type
Current20mA (internal shunt), DSI-5A, ext. shuntext. shunt
Potentiometer
LVDTDSI-LVDT
ChargeDSI-CHG
TEDS
IsolationNoneGalvanic isolation CH, GNDGalvanic isolation CH, GND125 Vrms Isolation CH, GND 125 Vrms Isolation CH, GND 125 Vrms Isolation CH, GND CAT III 600 V CAT II 1000 VCAT III 600 V CAT II 1000 VNone
Power consumption2 W1.5 W2 W2 W3 W1.5 W1 W1.3 W1.2 W
Rev: 1673622000

KRYPTON® MULTI amplifier overview

STGTHTH-HSRTDRTD-HSACCLVLADIOCNT
ConnectorsDB9, L2B10fThermocoupleThermocoupleL0B6fL0B6fBNCBNCBNCDB25L1T7f
#ch per module3x, 6x8x, 16x8x, 16x8x8x4x, 8x4x, 8x8x16xDI, 16xDO 8xDI, 8xDO4xCNT
Data rate / channel20 kS/s100 S/s100 S/s, upgradable to 10 kS/s100 S/s100 S/s, upgradable to 10 kS/s20 kS/s20 kS/s20 kS/s40 kS/s20 kS/s
Resolution24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bitdigital100 MHz timebase 5 ppm, 20 ppm max
Bandwidth0.49*fs0.49*fs (max. 1 kHz)0.49*fs0.49*fs0.49*fs10 MHz
Voltage ranges±10 V, ±1 V, ±100 mV, ±10 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±10 V, ±5 V, ±1 V, ±200 mV±50 V±20 mACMOS compatibleTTL (Low: <0.8 V, High > 2 V)
Input couplingDCDCDCDCDCDC, AC 0.1 Hz, 1 HzDCDCDC
Sensor excitation0...15 V max. 0.4 W/ch (45 mA limit)IEPE 4 mA, 8 mA--5 V / 300 mA 12 V / 120 mA Vsupply / 200 mA5 V /100 mA / ch 12 V / 50 mA / ch
Bridge connectionFull, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire
Programmable shunt100 kΩ
IEPE inputDSI-ACC
Resistance10 kΩ10 kΩ
Temperature (PTx)DSI-RTDPT100, 200, 500, 1000, 2000PT100, 200, 500, 1000, 2000
ThermocoupleDSI-THK, J, T, R, S, N, E, C, BK, J, T, R, S, N, E, C, B
Currentext. shunt DSIext. shunt
Potentiometer
LVDTDSI-LVDT
ChargeDSI-CHG
TEDS
Isolation voltageDifferential1000 V1000 V1000 V1000 VDifferential1000 V1000 V250 V
Isolation arrangementNoneCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDNoneCh-Ch & Ch-GNDCh-Ch & Ch-GNDIsolated common GNDIsolated common GND
Power consumption per module2.4 W (4 W 120 Ω @ 5 V load) 3xSTG; 5.9 W (8.9 W 120 Ω @ 5 V load) 6xSTG2.5 W (8xTH) 4 W (16xTH)2.6 W (8xTH-HS) 4.3 W (16xTH-HS)2.5 W2.5 W4.6 W3.5 W (4xLV) 6.7 W (8xLV)6.8 W2 W2.3W
Advanced functionsSupports all strain types, TEDS supportHigh isolation, support of main TC typesHigh isolation, support of main TC typesTEDS supportHigh isolation, high input rangeHigh isolation, 4-20 mA current loopSuperCounter®
Rev: 1668758400

Spécifications du KRYPTONi-1xACC

Analog inputs
Input typesVoltage, IEPE
Number of channels1
ADC Type24-bit SAR with anti-aliasing filter
Sampling RateSimultaneous 40 kS/s (50 kS/s while using it standalone) software-selectable
Voltage Mode
Voltage Ranges±10 V±5 V±1 V±200 mV
Typ. Input Accuracy±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)90 dB90 dB89 dB88 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)100 dB99 dB99 dB98 dB
Typ. Noise floor @ 10 kS/s-100 dB-99 dB-99 dB-98 dB
Typical CMR @ 400 Hz / 1 kHz130 dB / 120 dB122 dB / 119 dB104 dB / 97 dB90 dB / 84 dB
Gain Drifttyp. 10 ppm/K (max. 40 ppm/K)
Offset Drifttyp. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity< 0.02 %
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
IEPE input
Excitation4 mA, 8 mA
Compliance voltage24 V
Output Impedance
Sensor detectionShortcut: <4 V; Open: >19 V
TEDS supportIEPE mode only
Additional specifications
Input connectorBNC
Isolation125 Vrms channel to ground isolation
Power
Power supply9 - 48 V DC
Power consumption2 W (typ.)
Environmental
IP ratingIP65 / IP67 (see 1)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
1) Depending on the mating connector types
Rev: 1702375200

Spécifications du KRYPTONi-1xSTG

Analog input
Input typesVoltage, current, full bridge strain, half bridge strain, quarter bridge strain
Number of channels1
ADC Type24-bit SAR with anti-aliasing filter
Sampling RateSimultaneous 40 kS/s per channel (software-selectable)
Voltage Mode
Ranges±50 V±10 V±1 V±100 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/s89 dB88 dB88 dB87 dB
Typical SFDR @ 10 kS/s100 dB99 dB100 dB96 dB
Typical Noise floor @ 10 kS/s-103 dB-99 dB-103 dB-96 dB
Typical CMR @ 400 Hz / 1 kHz71 dB / 66 dB72 dB / 66 dB96 dB / 88 dB96 dB / 87 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC, AC 1 Hz
Input Impedance1 MΩ20 MΩ
Overvoltage Protection200 V50 V
Current Mode
Ranges20 mA2 mA
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor50 Ω
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation Voltage
Excitation voltageFree programmable (16-bit DAC)
Predefined LevelsUnipolar 0 - 24 V, Bipolar 0 - 12 V
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load< 0.01 %
Current Limit42 mA (400 mW max. Power)
ProtectionContinuous short to ground
Bridge mode
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Bridge ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional specifications
Input connectorDB9
Isolation125 Vrms channel to ground isolation
TEDS supportStandard + DSI adapters
Power
Power Supply9 - 48 V DC
Power consumption2.8 W (typ.)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
Rev: 1710761400

Spécifications du KRYPTONi-1xLV

Analog input
Input typesVoltage
Number of channels1
ADC Type24-bit SAR with anti-aliasing filter
Sampling RateSimultaneous 40 kS/s per channel (software-selectable)
Voltage Mode
Ranges±50 V±10 V±1 V±100 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical SNR @ 10 kS/s96 dB96 dB94 dB88 dB
Typical Dynamic Range @ 10 kS-130 dB-132 dB-137 dB-138 dB
Typical Noise floor @ 10 kS-108 dB-102 dB-107 dB-100 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC, AC 1 Hz
Input Impedance1 MΩ20 MΩ
Overvoltage Protection200 V50 V
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional specifications
Input connectorBNC
Isolation125 Vrms channel to ground isolation
Power
Power Supply9 - 48 V DC
Power consumption1.5 W (typ.)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
Rev: 1578868200

Spécifications du KRYPTONi-1xHV

Analog Input
Input typesVoltage
Number of channels1
ADC Type24-bit SAR with anti-aliasing filter
Sampling Rate40 kS/s (software-selectable)
Input range±1000 V
Input accuracy±0.03 % of reading ±0.2 V
Typ. Noise floor @ 10 kS/s-96 dB
Typ. Noise floor @ 40 kS/s-90 dB
Typ. CMR @ 400 Hz / 1 kHz-
Gain DriftTyp. 50 ppm (Max. 150ppm)
Offset DriftTyp. 1.5 mV/K (Max. 4 mV/K)
Gain Linearity-
Input CouplingDC
Input Impedance10 MΩ
Protection classCAT IV 600 V, CAT III 1000 V
Overvoltage Protection+-2 kVpeak
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional specifications
Input connector4 mm safety banana jack
Power
Power Supply9 - 48 V DC
Power consumption1 W (typ.)
Environmental
IP ratingIP65 / IP67 (see 1)
Physical
Dimensions62 x 56 x 36 mm
Weight300 g
1) Depending on the mating connector types
Rev: 1578868200

Spécifications du KRYPTONi-1xTH-HV

Inputs
Input typesThermocouple
Number of channels1
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Input Impedance100 MΩ
Thermocouple
TC typeType K
Accuracy±0.02 % of reading ±0.5 °C ±10 μV
Resolution< 0.001 °C
Sampling rates100, 80, 40, 20, 10 S/s
Typical Noise0.007°C RMS @ Type K @ 10 S/sec
Additional specifications
Input connectorK-type Thermocouple LEMO REDEL 2P series
Isolation voltageCAT III 600 V, CAT II 1000 V
Power
Power Supply9 - 48 V DC
Power consumption1.3 W (typ.)
Physical
Dimensions62 x 56 x 36 mm
Weight300 g
Rev: 1578868200

Caractéristiques techniques de KRYPTON-1xCNT

Counter
Input typeDigital
Number of channels1
Timebase100 MHz
Time base accuracyTypical: 5 ppm, Max: 20 ppm
Max. bandwidth10 MHz
Input Filter500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level CompatibilityTTL (Low: < 0.8 V, High > 2 V)
Input impedance100 kΩ pull-up to +3.3 V
Input Protection±25 V continuous
Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 100 mA max.
Output Voltage +12 V12 V +/-10 % 90 mA max.
Additional specifications
Input connectorLEMO 1T series 7-pin
Isolation-
Power
Power Supply9 - 48 V DC
Power consumption1.2 W (typ.)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
Rev: 1578868200

Caractéristiques techniques de KRYPTON-1xAO

Analog Output
Output typesVoltage
Number of channels1
DAC Resolution18 bit
FunctionFile replay, conditioned AI output, FGEN (software option), channel output
Update Rate1 kS/s (5 kS/s with 3rd party master)
Full Scale Output Range±10 V
Accuracy (typ.)0.1 % ±1 mV (0 to 20 mA load)
Temperature gain drift (typ.)±10 ppm/K
Temperature offset drift (typ.)±5 uV/K
SNR @ 1000 S/s output rate92 dB (sine wave, 250 Hz, ±9 V)
THD-90 dB
Output impedance0.45 Ω DC
Maximum output current20 mA
Settling time (0.05 % of set value)30 μs @ 1000 Ω load, -10 V to 10 V step
Max slew rate2.5 V/μs @ 1000 Ω load
Max capacitive load (2 % overshoot)10 nF
Maximum load500 Ω
Output protectionShort circuit protected
Additional specifications
Output connectorBNC
Power
Power supply9 - 48 V DC
Power consumption2 W (typ.)
Environmental
IP ratingIP65 / IP67 (see 1)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
1) Depending on the mating connector types
Rev: 1578868200

Spécifications du KRYPTONi-4xDI

Digital Inputs
Input typeDigital
Number of channels4
CompatibilityTTL / CMOS Voltage Levels
Input low levelUIN < 1 V
Input high levelUIN > 2 V
Input high current @ 5 V UIN3 mA typ.
Input high current @ 30 V UIN6 mA typ.
Propagation delay< 1 μs
Max. sampling rate40 kS/s
Non-Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 300 mA max. (see 1)
Output Voltage +12 V12 V +/-10 % 100 mA max. (see 1)
Output Voltage +VecatEtherCAT Bus Supply Voltage 200 mA max. (see 1)
Additional specifications
ConnectorDSUB15HD Male
Overvoltage protection30 V Continuous, 65 V peak
IsolationGalvanic isolation CH, GND
Power
Power supply9 - 48 V DC
Power consumption1.5 W (typ.)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200

Spécifications du KRYPTONi-4xDO

Digital Outputs
Output typeDigital
Number of channels4
Maximum update ratedepends on EtherCAT master cycle time
Output typeopen collector with active internal pullup to 5 V
Sinkmax 50 V, 2 A (resistive load, unprotected)
Source5 V, max. 40 mA (internally limited)
Max. switching frequency for internal PWM100 kHz
Non-Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 300 mA max. (see 1)
Output Voltage +12 V12 V +/-10 % 100 mA max. (see 1)
Output Voltage +VecatEtherCAT Bus Supply Voltage 200 mA max. (see 1)
Additional specifications
ConnectorDSUB15HD Female
IsolationGalvanic isolation CH, GND
Power
Power supply9 - 48 V DC
Power consumption2 W (typ.)
Physical
Dimensions62 x 56 x 29 mm
Weight250 g
1) Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Rev: 1578868200

Caractéristiques techniques de KRYPTON-8xACC

Analog inputsKRYPTON-8xACC
Input typeVoltage, IEPE
Number of channels8
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±10 V±5 V±1 V±200 mV
Input Accuracy±0.03 % of reading ±0.02 % of range ±0.2 mV
Typical Dynamic Range @ 10 kS/s-140 dB-137 dB138 dB-134 dB
Typical noise floor @ 10 kS/s-106 dB-106 dB106 dB-102 dB
Type. THD (20 kS/s, -1 dBFS sine wave @ 1 kHz)-94 dB-94 dB-93 dB-95 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)96 dB96 dB96 dB93 dB
Gain DriftTypical 10 ppm/K, max. 20 ppm/K
Offset DriftTypical 0.5 μV/K + 1 ppm of range/K, max 2 μV/K + 3 ppm of range/K
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
IEPE input
Excitation4 mA, 8 mA
Compliance voltage25 V
Output Impedance>100 kΩ
Sensor detectionShortcut: <4 V; Open: >19 V
Additional Specifications
Input connectorBNC
TEDs supportIEPE mode only
Power
Power Supply9 - 48 V DC
Power Consumption4.6 W
Environemental
IP rating (see 1)IP67
Physical
Weight1000 g
Slice Dimensions213 x 54 x 56 mm
Dimensions with Connectors213 x 54 x 66.8 mm
1) Depending on the mating connector types
Rev: 1703235600

Caractéristiques techniques de KRYPTON-4xACC

Analog inputsKRYPTON-4xACC
Input typeVoltage, IEPE
Number of channels4
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±10 V±5 V±1 V±200 mV
Input Accuracy±0.03 % of reading ±0.02 % of range ±0.2 mV
Typical Dynamic Range @ 10 kS/s-140 dB-137 dB138 dB-134 dB
Typical noise floor @ 10 kS/s-106 dB-106 dB106 dB-102 dB
Type. THD (20 kS/s, -1 dBFS sine wave @ 1 kHz)-94 dB-94 dB-93 dB-95 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)96 dB96 dB96 dB93 dB
Gain DriftTypical 10 ppm/K, max. 20 ppm/K
Offset DriftTypical 0.5 μV/K + 1 ppm of range/K, max 2 μV/K + 3 ppm of range/K
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
IEPE input
Excitation4 mA, 8 mA
Compliance voltage25 V
Output Impedance>100 kΩ
Sensor detectionShortcut: <4 V; Open: >19 V
Additional Specifications
Input connectorBNC
TEDs supportIEPE mode only
Power
Power Supply9 - 48 V DC
Power Consumption3 W
Environemental
IP rating (see 1)IP67
Physical
Weight700 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 66.8 mm
1) Depending on the mating connector types
Rev: 1703235600

Caractéristiques techniques de KRYPTON-3xSTG

Analog inputsKRYPTON-3xSTG
Input typeVoltage Full / half / quarter strain
Number of channels3
ADC Type24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling RateSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±10 V±1 V±100 mV±10 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS/s-139 dB-139 dB-129 dB-110 dB
Typical Noise Floor @ 10 kS/s-106 dB-105dB-97 dB-78 dB
Typical CMR @ 400 Hz / 1 kHz86 dB / 84 dB96 dB / 95 dB112 dB / 102 dB112 dB / 102 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC
Input Impedance10 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 ms)
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation Voltage
Excitation voltageFree programmable (16-bit DAC)
Predefined Levels0, 1, 2.5, 5, 10 and 15 VDC
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load< 0.01 %
Current Limit45 mA (400 mW max. Power)
ProtectionContinuous short to ground
Bridge mode
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
Input connectorDB9; L1T7f; L2B10f
TEDs supportStandard + DSI adapters
Power
Power Consumption3.5 W (4.8 W 120 Ω @ 5 V load)
Power Supply9 - 48 V DC
Environmental
IP ratingIP67
Physical
Weight740 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 58.2 mm

Caractéristiques techniques de KRYPTON-6xSTG

Analog inputsKRYPTON-6xSTG
Input typeVoltage Full / half / quarter strain
Number of channels6
ADC Type24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling RateSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±10 V±1 V±100 mV±10 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS/s-139 dB-139 dB-129 dB-110 dB
Typical Noise Floor @ 10 kS/s-106 dB-105dB-97 dB-78 dB
Typical CMR @ 400 Hz / 1 kHz86 dB / 84 dB96 dB / 95 dB112 dB / 102 dB112 dB / 102 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC
Input Impedance10 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 ms)
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation Voltage
Excitation voltageFree programmable (16-bit DAC)
Predefined Levels0, 1, 2.5, 5, 10 and 15 VDC
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load< 0.01 %
Current Limit45 mA (400 mW max. Power)
ProtectionContinuous short to ground
Bridge mode
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
Input connectorDB9; L1T7f; L2B10f
TEDs supportStandard + DSI adapters
Power
Power Consumption5.9 W (8.9 W load 120 Ω @ 5 V)
Power Supply9 - 48 V DC
Environmental
IP ratingIP67
Physical
Weight1100 g
Slice Dimensions213 x 54 x 56 mm
Dimensions with Connectors213 x 54 x 58.2 mm

Caractéristiques de KRYPTONi-4xLV

Analog inputKRYPTONi-4xLV
Input typeIsolated voltage
Number of channels4
ADC Type24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Range±50 V
Accuracy±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)104 dB
Typical noise floor @ 10 kS/s-106 dB
Type. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-104 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)105 dB
Typical CMR @ 400 Hz / 1 kHz105 dB / 94 dB
Gain DriftTypical 10 ppm/K, max. 20 ppm/K
Offset DriftTypical 5 μV/K, max. 10 μV/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance1 MΩ
Noise0.7 mVRMS
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 msec)
Analog input performance
Bandwidth (-3dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
Input ConnectorBNC
Isolation Voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power Consumption3.8 W
Environmental
IP Rating (see 1)IP67
Physical
Weight700 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 66.8 mm
1) Depending on the mating connector types

Caractéristiques techniques de KRYPTONi-8xLV

Analog inputKRYPTONi-8xLV
Input typeIsolated voltage
Number of channels8
ADC Type24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Range±50 V, ±100 V (see 2)
Accuracy±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)104 dB
Typical noise floor @ 10 kS/s-106 dB
Type. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-104 dB
Type. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)105 dB
Typical CMR @ 400 Hz / 1 kHz105 dB / 94 dB
Gain DriftTypical 10 ppm/K, max. 20 ppm/K
Offset DriftTypical 5 μV/K, max. 10 μV/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance1 MΩ
Noise0.7 mVRMS
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 msec)
Analog input performance
Bandwidth (-3dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
Input ConnectorBNC, Lemo 2 pin (see 2)
Isolation Voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power Consumption6.8 W
Environmental
IP Rating (see 1)IP67
Physical
Weight1000 g
Slice Dimensions213 x 54 x 56 mm
Dimensions with Connectors213 x 54 x 66.8 mm
1) Depending on the mating connector types
2) Upon request

KRYPTONi-8xLA specifications

Analog inputKRYPTONi-8xLA
Input typeIsolated current
Number of channels8
ADC Type24-bit oversampled SAR with 41 kHz anti-aliasing filter
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Current Mode
Range±20 mA
Accuracy±0.02 % of reading ±8 µA
Typical noise floor @ 10 kS/s-95 dB
Crosstalk (20 kS/s, -1 dBFS @ 1 kHz)-124 dB
Gain DriftTypical 10 ppm/K, max. 20 ppm/K
Offset DriftTypical 100 nA/K, max. 200 nA/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance50 Ω
Noise0.3 µARMS
Overvoltage Protection50 V
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
Input ConnectorBNC
Isolation Voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power Consumption6.8 W
Environmental
IP Rating (see 1)IP67
Physical
Weight1000 g
Slice Dimensions213 x 54 x 56 mm
Dimensions with Connectors213 x 54 x 66.8 mm
1) Depending on the mating connector types

Caractéristiques de KRYPTONi-8xTH

Analog inputsKRYPTONi-8xTH
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling ratesSimultaneous 100, 80, 40, 20, 10 S/s (software selectable)
Voltage Ranges
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±100 μV±0.02 % of reading ±10 μV
Typical Noise Floor @ 10 / 100 S/s-114 dB / -105 dB-109 dB / -100 dB
Gain DriftTypical 3 ppm/K (max. 10 ppm/K)
Offset Drift0.03 μV/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance100 MΩ
Thermocouple
Input typeTC Types: K, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ± 0.5 °C ± 10 μV
Typical Noise0.007 °C RMS @ Type K @ 10 S/s
Additional Specifications
Input connectorMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power supply9 - 48 V DC
Power consumption2.5 W
Environmental
IP rating (see 1)IP67
Physical
Weight720 g
Dimensions213 x 39 x 56 mm
1) Depending on the mating connector types, for non corrosive liquids only, IP65 standard

Caractéristiques de KRYPTONi-16xTH

Analog inputsKRYPTONi-16xTH
Input typeIsolated universal thermocouple and voltage
Number of channels16
ADC Type24-bit delta-sigma
Sampling ratesSimultaneous 100, 80, 40, 20, 10 S/s (software selectable)
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±100 μV±0.02 % of reading ±10 μV
Typical Noise Floor @ 10 / 100 S/s-114 dB / -105 dB-109 dB / -100 dB
Gain DriftTypical 3 ppm/K (max. 10 ppm/K)
Offset Drift0.03 μV/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance100 MΩ
Thermocouple
Input typeTC Types: K, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ± 0.5 °C ± 10 μV
Typical Noise0.02 °C RMS @ Type K @ 100 S/s
Additional Specifications
Input connectorMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power supply9 - 48 V DC
Power consumption4 W
Environmental
IP rating (see 1)IP67
Physical
Weight1000 g
Dimensions213 x 54 x 56 mm
1) Depending on the mating connector types, for non corrosive liquids only, IP65 standard

KRYPTON TH précision

TemperatureType KType JType TType RType SType NType EType BType C
-200 °C1.19 °C1.00 °C1.17 °C1.54 °C0.83 °C
-100 °C0.85 °C0.76 °C0.87 °C1.00 °C0.74 °C
0 °C0.75 °C0.70 °C0.76 °C2.38 °C2.34 °C0.89 °C0.67 °C1.27 °C
100 °C0.76 °C0.70 °C0.73 °C1.85 °C1.88 °C0.86 °C0.67 °C10.96 °C1.15 °C
400 °C0.82 °C0.76 °C0.74 °C1.54 °C1.63 °C0.85 °C0.71 °C3.03 °C1.11 °C
700 °C0.88 °C0.80 °C1.49 °C1.59 °C0.89 °C0.77 °C2.11 °C1.17 °C
1000 °C0.96 °C0.87 °C1.46 °C1.57 °C0.96 °C0.85 °C1.80 °C1.23 °C
1300 °C1.05 °C1.47 °C1.59 °C1.04 °C1.68 °C1.35 °C
1700 °C1.58 °C1.71 °C1.70 °C1.65 °C

Caractéristiques de KRYPTONi-16xTH-HS

Analog inputsKRYPTONi-16xTH-HS
Input type
Number of channels16
ADC Type24-bit delta-sigma
Sampling ratesSimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±50 μV±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -110 dB / -100 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007 %
Input CouplingDC
Input Impedance100 MΩ
Thermocouple
Input typeTC Types: K, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
Input connectorMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power consumptionTyp. 4.3 W (Max. 5 W)
Environmental
IP rating IP67
Physical
Weight1060 g
Dimensions213 x 54 x 56 mm
Rev: 1660298400

Caractéristiques techniques de KRYPTONi-8xTH-HS

Analog inputsKRYPTONi-8xTH-HS
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling ratesSimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±50 μV±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -110 dB / -100 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007 %
Input CouplingDC
Input Impedance100 MΩ
Thermocouple
Input typeTC Types: K, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
Input connectorMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power consumptionTyp. 2.6 W (Max. 3 W)
Environmental
IP rating IP67
Physical
Weight750 g
Dimensions213 x 39 x 56 mm
Rev: 1660298400

KRYPTON TH-HS précision

TemperatureType KType JType TType RType SType NType EType BType C
-200 °C1.00 °C0.86 °C0.98 °C1.24 °C0.71 °C
-100 °C0.75 °C0.69 °C0.77 °C0.85 °C0.67 °C
0 °C0.68 °C0.64 °C0.68 °C1.82 °C1.79 °C0.77 °C0.62 °C1.07 °C
100 °C0.69 °C0.65 °C0.67 °C1.46 °C1.47 °C0.76 °C0.62 °C7.96 °C0.96 °C
400 °C0.75 °C0.71 °C0.72 °C1.26 °C1.31 °C0.77 °C0.67 °C2.30 °C0.95 °C
700 °C0.81 °C0.75 °C1.23 °C1.30 °C0.82 °C0.73 °C1.67 °C1.01 °C
1000 °C0.88 °C0.82 °C1.23 °C1.31 °C0.88 °C0.83 °C1.47 °C1.07 °C
1300 °C0.96 °C1.26 °C1.34 °C0.98 °C1.40 °C1.17 °C
1700 °C1.36 °C1.45 °C1.45 °C1.34 °C

Spécifications du KRYPTONi-8xRTD

Analog inputsKRYPTONi-8xRTD
Input typesvoltage, resistor or universal Ptxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range ±10 μV±0.02% of reading ±0.01% of range ±10 μV
Typical Noise floor @ 10/100 S/s-108 dB / -98 dB-108 dB / -98 dB
Gain DriftTypical 3 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance1 MΩ
Temperature Mode
RangesPT500, PT1000, PT2000PT100, PT200
Measurement range-200 °C to +850 °C
Accuracy±0.05 % of reading ±0.2 °C
Temperature Drifttyp. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection3 wire or 4 wire
Resistance mode
Ranges0…10 kΩ0…1 kΩ
Accuracy±0.02 % of reading ±0.01 % of range
Input Connection3 wire or 4 wire
Additional Specifications
Input connectorLemo 0B 6pin EEA.0B.306.CLN
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power consumption2.5 W
Environmental
IP rating (see 1)IP65
Physical
Weight720 g
Dimensions213 x 39 x 58 mm
1) Depending on the mating connector types
Rev: 1564584000

Caractéristiques de KRYPTONi 8xRTD-HS

Analog inputsKRYPTONi-8xRTD-HS
Input typesVoltage, Resistance or Universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling Rate IOLITESimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -108 dB / -98 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007 %
Input CouplingDC
Input Impedance10 MΩ
Temperature
RangesPT500, PT1000, PT2000PT100, PT200
Excitation current150 uA400 uA
Measurement range-200 °C to +850 °C
Accuracy±0.02 % of reading ±0.2 °C
Temperature DriftTyp. ±2 ppm/K (Max. ±10 ppm/K)
Input Connection3-wire or 4-wire
Resistance Mode
Ranges0…10 kΩ0…1 kΩ
Excitation current150 uA400 uA
Accuracy±0.02 % of reading ±0.008 % of range
Input Connection3-wire or 4-wire
Additional Specifications
Input connectorLemo 0B 6pin EEA.0B.306.CLN
Isolation voltage1000 Vpeak channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.7 W)
Environmental
IP rating (see 1)IP65
Physical
Weight755 g
Dimensions213 x 39 x 58 mm
1) Depending on the mating connector types
Rev: 1564584000

Spécifications de KRYPTON-4xCNT

Digital inputs
Input typeDigital
Number of channels4
Input connectorLEMO 1T series 7-pin
Timebase100 MHz
Time base accuracyTypical: 5 ppm, Max: 20 ppm
Max. bandwidth10 MHz
Input Filter500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level CompatibilityTTL (Low: < 0.8 V, High > 2 V)
Input impedance100 kΩ pull-up to +3.3 V
Input Protection±25 V continuous
IsolationCh to GND isolation
Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 100 mA max. (400 mA to supply 4 channels)
Output Voltage +12 V12 V +/-10 % 50 mA max. (200 mA to supply 4 channels)
IsolationCh to GND isolation
Power
Power Supply9 - 48 V DC
Power consumptionTyp 2.3 W (Max 2.7 W)
Physical
Dimensions213 x 39 x 56 mm
Weight700 g
Rev: 1709799612

Caractéristiques de KRYPTONi-8xDI-8xDO

KRYPTONi-8xDI-8xDO
Digital Input
Isolated Input Channels8
CompatibilityCMOS Configuration
Input low levelUIN < 0.8 V
Input high levelUIN > 2.4 V
Input high current @ 5 VIIN < 1.8 mA
Input high current @ 30 VIIN < 6 mA
Propagation delay< 1 μs
Sampling rateSimultaneous 40 kS/s
Overvoltage protection40 V continuous (65 V peak)
Isolation voltage peak250 V channel/ground & channel/channel
Digital Output
Isolated Output Channels8
CompatibilityOpen collector with 10 kΩ pull-up to +5 V
Maximum sink current150 mA (not protected)
Maximum switching voltage50 V
Propagation delay< 20 μs
Maximum update ratedepending on EtherCAT master
Isolation voltage peak250 V channel to ground, no channel to channel isolation
Power
Power Supply9 - 48 V DC
Power consumption2 W
Environmental
IP ratingIP67
Physical
Weight700 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 58.2 mm
Rev: 1602590400

Caractéristiques de KRYPTONi-16xDO

KRYPTONi-16xDO
Digital Output
Isolated Output Channels16
CompatibilityOpen collector with 10 kΩ pull-up to +5 V
Maximum sink current150 mA (not protected)
Maximum switching voltage50 V
Propagation delay< 20 μs
Maximum update ratedepending on EtherCAT master
Isolation voltage peak250 V channel to ground, no channel to channel isolation
Power
Power Supply9 - 48 V DC
Power consumption2 W
Environmental
IP ratingIP67
Physical
Weight700 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 58.2 mm
Rev: 1602590400

Caractéristiques de KRYPTONi-16xDI

KRYPTONi-16xDI
Digital Input
Isolated Input Channels16
CompatibilityCMOS Configuration
Input low levelUIN < 0.8 V
Input high levelUIN > 2.4 V
Input high current @ 5 VIIN < 1.8 mA
Input high current @ 30 VIIN < 6 mA
Propagation delay< 1 μs
Sampling rateSimultaneous 40 kS/s
Overvoltage protection40 V continuous (65 V peak)
Isolation voltage peak250 V channel/ground & channel/channel
Power
Power Supply9 - 48 V DC
Power consumption2 W
Environmental
IP ratingIP67
Physical
Weight700 g
Slice Dimensions213 x 39 x 56 mm
Dimensions with Connectors213 x 39 x 58.2 mm
Rev: 1602590400
Haut de page