Virranmuuntimien tekniset eritelmät
- DC-CT-1000I virta-anturin tekniset tiedot
- Flux gate AC/DC -virtapihdit tekniset tiedot
- Hall-efektin AC/DC-virtapihtejä koskevat tekniset tiedot
- Vaihtovirtapiirien tekniset eritelmät
- Nollavirtamuuntajien tekniset tiedot
- AC Rogowski-kelojen tekniset tiedot
- MCTS-virtalähteen tekniset tiedot
- DSi-PWR-MCTS-SINGLE
DC-CT-1000I virta-anturin tekniset tiedot
| DC-CT-1000I-S22xA | DC-CT-1000I-S45xA | Unit | |||||
|---|---|---|---|---|---|---|---|
| Rated/Nominal Measuring Current DC | 1000 | 1000 | A | ||||
| Rated/Nominal Measuring Current AC RMS | 707 | 707 | A | ||||
| Transformer Ratio | 1680 | 1680 | turns | ||||
| Nominal Secondary Current at IP (@1000A) | ~595.2 | ~595.2 | mA | ||||
| Frequency Bandwidth @ IP = 0.7 ARMS | 1000 @ -0.5 dB | 500 @ -0.5 dB | kHz | ||||
| Inner diameter | 22 | 45 | mm | ||||
| Weight | 500 | 650 | g | ||||
| Dimentsions | 77 x 57 x 46.7 | 100 x 80 x 46.3 | mm | ||||
| DC Accuracy @ Ta = 23◦C | Typ µ | Max 5σ | Typ µ | Max 5σ | |||
| Gain Error, BFSL over Ip @ Ta = 23◦C | 22 | < 163 | 46 | < 246 | ppm | ||
| ... @ Ta = −40◦C | 46 | < 193 | 79 | < 127 | ppm | ||
| ... @ Ta = 85◦C | 43 | < 194 | 120 | < 351 | ppm | ||
| Gain Off-Center Error Up/Down | 50 | < 100 | 150 | < 250 | ppm | ||
| ... Left/Right | 20 | < 50 | 50 | < 100 | ppm | ||
| Integral Non-Linearity including Hysteresis @ Ta = 23◦C | 22 | < 62 | 52 | < 114 | ppm/Apeak | ||
| ... Ta = −40◦C | 26 | < 107 | 83 | < 187 | ppm/Apeak | ||
| ... Ta = 85◦C | 12 | < 86 | 38 | < 117 | ppm/Apeak | ||
| Startup, Finder, Degauss, Offset RTI @ Ip = 0 A, Ta = 23◦C | 1.3 | < 10 | 4.1 | < 25 | mA | ||
| ... Ta = −40◦C | 1.7 | < 10 | 3.5 | < 25 | mA | ||
| ... Ta = 85◦C | 13.7 | < 83 | 11.4 | < 55 | mA | ||
| Long Term Stability at IP = 500 A including self-heating | < 10 | < 15 | mA | ||||
| AC Accuracy @ Ta = 23◦C | Typ µ | Max 5σ | Typ µ | Max 5σ | |||
| AC Flatness < 100 kHz | < 0.1 | < 0.1 | dB | ||||
| ... < 1 MHz | < 0.5 | < 1 | dB | ||||
| Phase Shift < 100 kHz | < 1° | < 2° | deg | ||||
| ... < 1 MHz | < 2° | < 5° | deg | ||||
| Typical RMS Noise at 10 kHz and entire TA | 0.6 | ~ 1.3 | 0.7 | ~ 1.4 | mA | ||
| ... 100 kHz and entire TA | 1.2 | ~ 2.0 | 1.0 | ~ 1.8 | mA | ||
| ... 1 MHz and entire TA | 5.5 | ~ 6.5 | 7.7 | ~ 8.2 | mA | ||
| Power Supply | Min | Typ | Max | Min | Typ | Max | |
| Bipolar Supply voltage | ±12 | ±15 | ±17.5 | ±12 | ±15 | ±17.5 | V |
| Unipolar Supply voltage | 24 | 30 | 35 | 24 | 30 | 35 | V |
| Power Consumption | 0.56 W (max. 0.7W) @Idle mode 6.6 W (max. 8W) @ IP = 1000A & Burden 1 Ω 7.6 W (max. 9 W) @ IP = 1000A & Burden 3 Ω | 0.56 W (max. 0.7W) @Idle mode 6.6 W (max. 8W) @ IP = 1000A & Burden 1 Ω 7.6 W (max. 9 W) @ IP = 1000A & Burden 3 Ω | W | ||||
| Isolation CAT II / CAT III non-insulated wire | 1000 / 600 | 1000 / 600 | V | ||||
| Isolation CAT II / CAT III insulated wire | 1000 | 1000 | V | ||||
| Storage and Operating Temperature | −40 - 85 | −40 - 85 | °C | ||||
| Rev. 04062026 | |||||||
Flux gate AC/DC -virtapihdit tekniset tiedot
| DS-CLAMP-20DC | DS-CLAMP-200DC | DS-CLAMP-500DCS | DS-CLAMP-500DC | DS-CLAMP-1000DC | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Type | Flux gate | Flux gate | Flux gate | Flux gate | Flux gate | |||||||
| Current Range | 20 A DC or AC RMS | 200 A DC or AC RMS | 500 A DC or AC RMS | 500 A DC or AC RMS | 1000 A DC or AC RMS | |||||||
| Sensitivity | 100 mV/A | 10 mV/A | 4 mV/A | 4 mV/A | 2 mV/A | |||||||
| Bandwidth | DC to 1 MHz | DC to 500 kHz | DC to 200 kHz | DC to 100 kHz | DC to 20 kHz | |||||||
| Bandwidth (upgraded after 2022) | DC to 2 MHz | DC to 700 kHz | DC to 500 kHz | DC to 200 kHz | DC to 100 kHz | |||||||
| TEDS | Fully supported | Fully supported | Fully supported | Fully supported | Fully supported | |||||||
| Conductor Position Sensitivity | max. ± 0.1 % of reading | max. ± 0.1 % of reading | max. ± 0.1 % of reading | max. ± 0.2 % of reading | max. ± 0.2 % of reading | |||||||
| Zero Offset (+25°C) | max. 10mA | max. ± 100 mA | max. ± 250 mA | max. ± 250 mA | max. ± 200 mA | |||||||
| Error due Earth Magnetic Field | max. ± 50 mA | max. ± 50 mA | max. ± 100 mA | max. ± 150 mA | max. ± 150 mA | |||||||
| Temp. Coefficient | ± 0.01 %/°C | ± 0.01 %/°C | ± 0.01 %/°C | ± 0.01 %/°C | ± 0.01 %/°C | |||||||
| Accuracy | ||||||||||||
| Frequency | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | ||
| DC | ± 0.2 % rdg. ± 10 mA | - | ± 0.2 % rdg. ± 40 mA | - | ± 0.3 % rdg. ± 100 mA | - | ± 0.2 % rdg. ± 100 mA | - | ± 0.2 % rdg. ± 200 mA | - | ||
| to 100 Hz | ± 0.2 % rdg. ± 2 mA | ± 0.1 ° | ± 0.2 % rdg. ± 20 mA | ± 0.1 ° | ± 0.3 % rdg. ± 50 mA | ± 0.1 ° | ± 0.2 % rdg. ± 50 mA | ± 0.1 ° | ± 0.2 % rdg. ± 100 mA | ± 0.1 ° | ||
| 100 - 500 Hz | ± 0.3 % rdg. ± 4 mA | ± 0.2 ° | ± 0.3 % rdg. ± 40 mA | ± 0.2 ° | ± 0.3 % rdg. ± 100 mA | ± 0.2 ° | ± 0.3 % rdg. ± 100 mA | ± 0.2 ° | ± 0.5 % rdg. ± 200 mA | ± 0.2 ° | ||
| 500 Hz - 1 kHz | ± 0.5 % rdg. ± 4 mA | ± 0.5 ° | ± 0.5 % rdg. ± 40 mA | ± 0.5 ° | ± 0.5 % rdg. ± 100 mA | ± 0.5 ° | ± 0.5 % rdg. ± 100 mA | ± 0.5 ° | ± 1.0 % rdg. ± 200 mA | ± 0.5 ° | ||
| 1 kHz - 5 kHz | ± 1.0 % rdg. ± 4 mA | ± 1.0 ° | ± 1.0 % rdg. ± 40 mA | ± 1.0 ° | ± 1.0 % rdg. ± 100 mA | ± 1.0 ° | ± 1.0 % rdg. ± 100 mA | ± (0.5 f [kHz]) ° | ± 2.0 % rdg. ± 200 mA | ± (0.7 f [kHz]) ° | ||
| 5 kHz - 10 kHz | ± 1.5 % rdg. ± 4 mA | ± 1.5 ° | ± 1.5 % rdg. ± 40 mA | ± 1.5 ° | ± 1.5 % rdg. ± 100 mA | ± 1.5 ° | ± 1.5 % rdg. ± 100 mA | ± (0.5 f [kHz]) ° | ± 5.0 % rdg. ± 200 mA | ± (0.7 f [kHz]) ° | ||
| 10 kHz - 20 kHz | ± 2 % rdg. ± 4 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 5 % rdg. ± 40 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 5 % rdg. ± 100 mA | ± (0.15 f [kHz]) ° | ± 5 % rdg. ± 100 mA | ± (0.5 f [kHz]) ° | ± 30 % rdg. ± 200 mA | ± (0.7 f [kHz]) ° | ||
| 20 kHz - 50 kHz | ± 2 % rdg. ± 4 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 5 % rdg. ± 40 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 5 % rdg. ± 100 mA | ± (0.15 f [kHz]) ° | ± 10 % rdg. ± 250 mA | ± (0.5 f [kHz]) ° | ± 30 % rdg. ± 200 mA | ± (0.7 f [kHz]) ° | ||
| 50 kHz - 100 kHz | ± 5 % rdg. ± 10 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 10 % rdg. ± 100 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 15 % rdg. ± 250 mA | ± (0.15 f [kHz]) ° | ± 30 % rdg. ± 250 mA | ± (0.5 f [kHz]) ° | - | - | ||
| 100 kHz - 200 kHz | ± 10 % rdg. ± 10 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 15 % rdg. ± 40 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 30 % rdg. ± 250 mA | ± (0.15 f [kHz]) ° | - | - | - | - | ||
| 200 kHz - 300 kHz | ± 10 % rdg. ± 10 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 15 % rdg. ± 40 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 30 % rdg. ± 250 mA | ± (0.15 f [kHz]) ° | - | - | - | - | ||
| 300 kHz - 500 kHz | ± 15 % rdg. ± 10 mA | ± (0.5 + 0.1 f [kHz]) ° | ± 30 % rdg. ± 100 mA | ± (0.5 + 0.1 f [kHz]) ° | - | - | - | - | - | - | ||
| 500 kHz - 1 MHz | ± 30 % rdg. ± 10 mA | ± (0.5 + 0.1 f [kHz]) ° | - | - | - | - | - | - | - | - | ||
| General Specifications | ||||||||||||
| Dimensions [mm] | 153 x 67 x 25 | 153 x 67 x 25 | 153 x 67 x 25 | 238 x 116 x 35 | 238 x 116 x 35 | |||||||
| Max. Conductor Size | 20 mm | 20 mm | 20 mm | 50 mm | 50 mm | |||||||
| Power Supply | ± 11 V to ± 15 V | ± 11 V to ± 15 V | ± 11 V to ± 15 V | ± 11.5 V to ± 15 V | ± 11.5 V to ± 15 V | |||||||
| Current Consumption | max. 5 VA | max. 6 VA | max. 7 VA | max. 7 VA | max. 7 VA | |||||||
| Operating Environment | Indoors, Pollution Degree II, altitude up to 2000m | Indoors, Pollution Degree II, altitude up to 2000m | Indoors, Pollution Degree II, altitude up to 2000m | Indoors, Pollution Degree II, altitude up to 2000m | Indoors, Pollution Degree II, altitude up to 2000m | |||||||
| Operating Temp. | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | |||||||
| Operating Humidity | up to 80 % (not condensing) | up to 80 % (not condensing) | up to 80 % (not condensing) | up to 80 % (not condensing) | up to 80 % (not condensing) | |||||||
| Safety Standards | EN61010 | EN61010 | EN61010 | EN61010 | EN61010 | |||||||
| EMC Standards | EN61326 | EN61326 | EN61326 | EN61326 | EN61326 | |||||||
| PWR-MCTS2 needed | Yes | Yes | Yes | Yes | Yes | |||||||
| Compatible amplifiers (see 1) | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43 | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43 | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43 | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43 | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI IOLITE STG, IOLITE LVe KRYPTON STG DEWE 43 | |||||||
| Cable length | 3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS | 3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS | 3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS | 3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS | 3 m - MCTS to Clamp 0.3 m - Amplifier to MCTS | |||||||
| 1) The ranges of the IOLITE and KRYPTON amplifiers might affect the resolution of the measured values. | ||||||||||||
| NOTE: The specifications in the table above are refering to the latest HIOKI current clamp models | ||||||||||||
| Rev. 23022026 | ||||||||||||
Hall-efektin AC/DC-virtapihtejä koskevat tekniset tiedot
| DS-CLAMP-30DC | DS-CLAMP-150DC | DS-CLAMP-150DCS | DS-CLAMP-300DC | DS-CLAMP-1800DC | |
|---|---|---|---|---|---|
| Type | Hall Effect | Hall Effect | Hall Effect | Hall Effect | Hall Effect |
| Current Range | 30 A DC or AC peak | 200 A DC or 150 A AC RMS | 250 A DC or 150 A AC RMS | 300 A DC or AC RMS | 1800 A DC or AC peak |
| Sensitivity | 100 mV/A | 20 mV/A | 10 mV/A | 1 mV/A | 1 mV/A |
| Accuracy (+25°C) | ± 1 % of reading ± 2 mA | ± 1 % of reading ± 2 mA | ± 1 % of reading ± 5 mA | ± 1 % of reading ± 100 mA | 0 - 1000 A: ± 2.5 % of reading ± 0.5 A 1000 - 1500 A: ± 3.5 % of reading 1500 - 1800 A: ± 5 % of reading |
| Bandwidth | DC to 20 kHz | DC to 100 kHz | DC to 100 kHz | DC to 20 kHz | DC to 20 kHz |
| Resolution | ± 1 mA | ± 1 mA | ± 1 mA | ± 100 mA | ± 200 mA |
| TEDS | Fully supported | Fully supported | Fully supported | Fully supported | Fully supported |
| Conductor Position Sensitivity | - | ± 0.5 % relative to center reading | ± 1 % relative to center reading | ± 1.5 % relative to center reading | ± 1.5 % relative to center reading |
| Zero Offset (+25°C) | - | ± 10 mV max. + 1 mV/°C | ± 10 mV max. + 0.1 mV/°C | ± 10 mV max. | - |
| Temp. Coefficient | ± 0.01 % of reading / °C | ± 0.02 % of reading / °C | ± 0.02 % of reading / °C | ± 0.1 % of reading / °C | ± 0.15 % of reading / °C |
| Zero | External zero correction | Auto zero @ power supply of sensor | External zero correction | External zero correction | Auto zero via push-button |
| General Specifications | |||||
| Dimensions [mm] | 200 x 55 x 15 | 200 x 55 x 15 | 100.4 x 65 x 25 | 192.60 x 55.30 x 15 | 200 x 55 x 15 |
| Max. Conductor Size | 32 mm | 32 mm | 25 mm | 25 mm | 32 mm |
| Power Supply | + 12 V | ± 10 V | ± 10 V | + 12 V ± 3 V | + 9 V |
| Current Consumption | 30 mA + 1 mA/A measured | 30 mA + 1mA/A measured | 25 mA + 1mA/A measured | max. 30 mA | max. 25 mA |
| Jaws Open Indication | No | Yes | No | No | No |
| Operating Temp. | 0 to + 50 °C | 0 to + 60 °C | -20 to + 65 °C | 0 to + 50 °C | 0 to + 50 °C |
| Operating Humidity | - | 15 % to 85 % (not condensing) | 15 % to 85 % (not condensing) | - | - |
| Safety Standards | EN 61010-1 EN 61010-2-032 | EN 61010-1 EN 61010-2-032 | EN 61010-1:2010 EN 61010-2-032:2012 | EN 61010-1 EN 61010-2-032 | EN 61010-1 EN 61010-2-032 |
| Safety | 300 Vrms CAT I | 300 Vrms CAT III | 300 Vrms CAT III | 300 Vrms CAT III | 300 Vrms CAT I |
| EMC Standards | EN 61326-2-2 | EN 61326-2-2:2013 | EN 61326-1:2013 | EN 61326-2-2 | EN 61326-2-2 |
| PWR-MCTS2 needed | No | No | No | No | No |
| Compatible Amplifiers | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG / UNI IOLITE LVe DEWE-43 (see 2) | SIRIUS LV / HS-LV (see 1) | SIRIUS LV / HS-LV (see 1) | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG / STGM / UNI IOLITE STG / LVe KRYPTON STG DEWE-43 | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG / STGM / UNI IOLITE STG / LVe KRYPTON STG DEWE-43 |
| Cable length | 2 m | 2.9 m | 2.9 m | 2.9 m | 2.9 m |
| 1) *in-rush current is too high, so the clamps are not compatible with other amplifiers | |||||
| 2) **current consumption exceeds the maximum range of other amplifiers | |||||
| Rev. 23022026 | |||||
Vaihtovirtapiirien tekniset eritelmät
| DS-CLAMP-5AC | DS-CLAMP-15AC | DS-CLAMP-200AC | DS-CLAMP-1000AC | |
|---|---|---|---|---|
| Type | Iron-Core | Iron-Core | Iron-Core | Iron-Core |
| Range | 5 A AC RMS | 15 A AC RMS | 200 A AC RMS | 1000 A AC RMS |
| Sensitivity | 100 mV/A | 100 mV/A | 10 mV/A | 1 mV/A |
| Accuracy (+25 °C) | 5 mA - 0.5 A ± 2 % of reading 0.5 A - 1 A ± 1 % of reading 1 A - 5 A ±0 .5 % of reading | 10 mA - 100 mA ≤ 3 % of reading 100 mA - 1 A ≤ 2.5 % of reading 1 A - 12 A ≤ 1 % of reading | 0.5 A - 10 A ≤ 3 % of reading + 5mV 10 A - 40 A ≤ 2.5 % of reading + 5 mV 40 A - 100 A ≤ 2 % of reading + 5mV 100 A - 240A ≤ 1 % of reading + 5mV | 1 mA - 100 mA ≤ 3 % of reading + 5 μA 100 mA - 1 A ≤ 2 % of reading + 3 μA 1 A - 10 A ≤ 1 % of reading 10 A - 100 A ≤ 0.5 % of reading 100 A - 1200 A ≤ 0.3 % of reading |
| Phase Error | 5 mA - 0.5 A ± 2 ° 0.5 A - 1 A ± 1° 1 A - 5 A ± 1 ° | 10 mA - 100 mA not specified 100 mA - 1 A ≤ 5 ° 1 A - 12 A ≤ 3 ° | 0.5 A - 10 A not specified 10 A - 40 A ≤ 5 ° 40 A - 100A ≤ 3 ° 100 A - 240 A ≤ 2.5 ° | 1 mA - 100 mA not specified 100 mA - 1 A not specified 1 A - 10 A ≤ 2 ° 10 A - 100A ≤ 1 ° 100 A - 1200 A ≤ 0.7 ° |
| Bandwidth | 40 Hz to 5 kHz | 40 Hz to 10 kHz | 40 Hz to 10 kHz | 30 Hz to 10 kHz |
| TEDS | Fully supported | Fully supported | Fully supported | Fully supported |
| Conductor Position Sensitivity | ≤ 0.5 % of reading | ≤0.5 % of output signal at 50/60 Hz | ≤0.5 % of output signal at 50/60 Hz | ≤0.1 % of output signal for frequencies ≤ 400 Hz |
| Temperature Coefficient | ±0.015 % of reading / °C | ≤ 0.2 % of output signal per 10 °K | ≤ 0.15 % of output signal per 10 °K | ≤ 0.2 % of output signal per 10 °K |
| Influence of Frequency | - | < 5 % of output signal from 20 Hz ... 1 kHz < 10 % of output signal from 1 kHz ... 10 kHz | < 3 % of output signal from 40 Hz ... 1 kHz < 12 % of output signal from 1 kHz ... 10 kHz | < 1 % of output signal from 30 Hz ... 48 Hz < 0.5 % of output signal from 35 Hz ... 1 kHz < 1 % of output signal from 1 kHz ... 5 kHz |
| General Specifications | ||||
| Dimensions [mm] | 102 x 32 x 23.5 | 135 x 51 x 30 | 135 x 51 x 30 | 216 x 111 x 45 |
| Max. Conductor Size | 15 mm | 20 mm | 20 mm | 52 mm |
| Operating Temperature | -10 °C to +55 °C | -10 °C to +55 °C | -10 °C to +55 °C | -10 °C to +50 °C |
| Operating Humidity | 15% to 85 % (not condensing) | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C |
| Safety Standards | EN 61010-1 EN 61010-2-032 | Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032 | Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032 | Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032 |
| Safety | CAT III 600V | CAT III 600V CAT IV 300V | CAT III 600V CAT IV 300V | CAT III 600V CAT IV 300V |
| EMC Standards | EN 61326-2-2 | EN 50081-1: class B EN 50082-2: Electrostatic discharge: IEC 1000-4-2 Radiated field: IEC 1000-4-3 Fast transients: IEC 1000-4-4 Magnetic field at 50 Hz: IEC 1000-4-8 | EN 50081-1: class B EN 50082-2: Electrostatic discharge: IEC 1000-4-2 Radiated field: IEC 1000-4-3 Fast transients: IEC 1000-4-4 Magnetic field at 50 Hz: IEC 1000-4-8 | EN 50081-1: class B EN 50082-2: Electrostatic discharge: IEC 1000-4-2 Radiated field: IEC 1000-4-3 Fast transients: IEC 1000-4-4 Magnetic field at 50 Hz: IEC 1000-4-8 |
| PWR-MCTS2 needed | No | No | No | No |
| Compatible Amplifiers | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe |
| Cable length | 2 m | 1.5 m | 1.5 m | 1.5 m |
| Rev. 23022026 | ||||
Nollavirtamuuntajien tekniset tiedot
| CT 100 | CT 200 | CT 400 | CT 500 | CT 1000 | CT 2000 | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Type | Zero-Flux | Zero-Flux | Zero-Flux | Zero-Flux | Zero-Flux | Zero-Flux | ||||||
| Primary Current Range DC RMS Sinus | 100 A | 200 A | 400 A | 500 A | 1000 A | 2000 A | ||||||
| Conversion ratio | 1:500 | 1:1000 | 1:1500 | 1:750 | 1:1500 | 1:2000 | ||||||
| Overload Ability Short Time (100 ms) | 20 kApk | 20 kApk | 20 kApk | 5000 Apk | 5000 Apk | 10000 Apk | ||||||
| Max. measurement resistor (100 % of Ip) | 25 Ω | 20 Ω | 10 Ω | 5 Ω | 4 Ω | 3.5 Ω | ||||||
| Step response (0 ... 90%) | 0.2 μs | 0.2 μs | 1 μs | 1 μs | 1 μs | 1 μs | ||||||
| Temperature influence | 0.2 ppm/K | 0.2 ppm/K | 0.1 ppm/K | 1 ppm/K | 0.3 ppm/K | < 0.1 ppm/k | ||||||
| Nominal secondary current | 200 mA at 100 A | 200 mA at 200 A | 266 mA at 400 A | 666 mA at 500 A | 666 mA at 1000 A | 1 A at 2000 A | ||||||
| Bandwidth ( -3 dB) | DC ... 2 MHz | DC ... 1.1 MHz | DC ... 800 kHz | DC ... 520 kHz | DC ... 440 kHz | DC ... 140 kHz | ||||||
| Linearity | 1.5 ppm | 1.2 ppm | 0.8 ppm | 3 ppm | 3 ppm | 3 ppm | ||||||
| Offset | < 0.0015 % | < 0.0010 % | < 0.0008 % | < 0.00115 % | < 0.0012 % | < 0.0012 % | ||||||
| Accuracy | ||||||||||||
| Frequency | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude | Phase Error | Amplitude ¹ | Phase Error ¹ |
| DC | 0.002 % | - | 0.001 % | - | 0.0008 % | - | 0.00115 % | - | 0.0012 % | - | 0.0012 % | - |
| to 100 Hz | 0.015 % | ± 0.01 ° | 0.015 % | ± 0.01 ° | 0.015 % | ± 0.01 ° | 0.015 % | ± 0.01 ° | 0.015 % | ± 0.01 ° | 0.015 % | ± 0.01 ° |
| 100 - 1 kHz | 0.025 % | ± 0.05 ° | 0.02 % | ± 0.02 ° | 0.02 % | ± 0.01 ° | 0.02 % | ± 0.01 ° | 0.02 % | ± 0.01 ° | 0.05 % | ± 0.05 ° |
| 1 kHz - 10 kHz | 0.2 % | ± 0.1 ° | 0.15 % | ± 0.05 ° | 0.15 % | ± 0.1 ° | 0.1 % | ± 0.05 ° | 0.15 % | ± 0.1 ° | 0.25 % | ± 0.1 ° |
| 10 kHz - 20 kHz | 0.5 % | ± 0.25 ° | 0.5 % | ± 0.25 ° | 0.5 % | ± 0.5 ° | 0.2 % | ± 0.5 ° | 1.5 % | ± 1 ° | 1 % | ± 1 ° |
| 20 kHz - 50 kHz | 0.5 % | ± 0.25 ° | 0.5 % | ± 0.25 ° | 0.5 % | ± 0.5 ° | 0.2 % | ± 0.5 ° | 1.5 % | ± 1 ° | - | - |
| 50 kHz - 100 kHz | 1 % | ± 0.5 ° | 1 % | ± 0.5 ° | 1 % | ± 1 ° | 0.5 % | ± 1 ° | 4 % | ± 2 ° | - | - |
| General Specifications | ||||||||||||
| Rated isolation voltage RMS, single isolation CAT III, pollution deg. 2, IEC 61010-1 standards, EN 50178 standards | 1000 V | 1000 V | 1000 V | 1000 V | 1000 V | 1000 V | ||||||
| Test voltage 50 / 60 Hz, 1 min | 4.95 kV | 4.95 kV | 4.95 kV | 4.2 kV | 4.2 kV | 6 kV | ||||||
| Inner diameter | 28 mm | 28 mm | 28 mm | 38 mm | 38 mm | 70 mm | ||||||
| Dimensions | 93 x 78.8 x 49.5 | 94 x 78.8 x 49.5 | 95 x 78.8 x 49.5 | 128 x 106 x 54 | 128 x 106 x 54 | 231 x 220 x 76 | ||||||
| Supply voltage (±5 %) | ±15 V | ±15 V | ±15 V | ±15 V | ±15 V | ±15 V | ||||||
| Operating humidity | 20 % to 80 % (not condensing) | 20 % to 80 % (not condensing) | 20 % to 80 % (not condensing) | 20 % to 80 % (not condensing) | 20 % to 80 % (not condensing) | 20 % to 80 % (not condensing) | ||||||
| Operating temperature | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | - 40 °C to + 85 °C | ||||||
| DEWESoft® Shunt | 5 Ω | 5 Ω | 5 Ω | 1 Ω | 1 Ω | 1 Ω | ||||||
| PWR-MCTS2 needed | Yes | Yes | Yes | Yes | Yes | Yes | ||||||
| Compatible amplifiers (see 1) | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM, SIRIUS UNI DEWE 43 IOLITE STG, KRYPTON STG IOLITE LVe | ||||||
| Cable length | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | 5 m - MCTS to Transducer 0.3 m - Amplifier to MCTS | ||||||
| Data Sheet | ||||||||||||
| 1) The ranges of the IOLITE and KRYPTON amplifiers might affect the resolution of the measured values. | ||||||||||||
AC Rogowski-kelojen tekniset tiedot
| DS-FLEX-3000-17 | DS-FLEX-3000-35 | DS-FLEX-3000-35HS | DS-FLEX-3000-80 | DS-FLEX-30000-120 | |
|---|---|---|---|---|---|
| Type | Rogowski coil | Rogowski coil | Rogowski coil | Rogowski coil | Rogowski coil |
| Current Range | 3 A, 30 A, 300 A, 3000 A AC RMS | 3 A, 30 A, 300 A, 3000 A AC RMS | 4500 A AC peak | 3 A, 30 A, 300 A, 3000 A AC RMS | 30 A, 300 A, 3000 A, 30000 A AC RMS |
| Sensitivity | 1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A | 1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A | 1 mV/A | 1000 mV/A, 100 mV/A, 10 mV/A, 1 mV/A | 100 mV/A, 10 mV/A, 1 mV/A, 0.1 mV/A |
| Accuracy (+25 °C) | 3 A: ≤ 1 % + 40 mV 30 A: ≤ 1 % + 4 mV 300 A: ≤ 1.5 % + 0.4 mV (I < 10 % IN) ≤ 1 % + 0.4 mV (I ≥ 10 % IN) 3000 A: ≤ 1.5 % + 0.04 mV (I < 10 % IN) ≤ 1 % + 0.04 mV (I ≥ 10 % IN) | 3 A: ≤ 1 % + 40 mV 30 A: ≤ 1 % + 4 mV 300 A: ≤ 1.5 % + 0.4 mV (I < 10 % IN) ≤ 1 % + 0.4 mV (I ≥ 10 % IN) 3000 A: ≤ 1.5 % + 0.04 mV (I < 10 % IN) ≤ 1 % + 0.04 mV (I ≥ 10 % IN) | ≤ 1.0 % + 0.3 A | 3 A: ≤ 1 % 30 A: ≤ 1 % 300 A: ≤ 1.5 % (I < 10 % IN) ≤ 1 % (I ≥ 10 % IN) 3000 A: ≤ 1.5 % (I < 10 % IN) ≤ 1 % (I ≥ 10 % IN) | 30 A: ≤ 1 % 300 A: ≤ 1 % 3000 A: ≤ 1.5 % (I < 10 % IN) ≤ 1 % (I ≥ 10 % IN) 30000 A: ≤ 1.5 % (I < 10 % IN) ≤ 1 % (I ≥ 10 % IN) |
| Phase Error | ≤ 1° (0.5° typical) @ 50 Hz | ≤ 1° (0.5° typical) @ 50 Hz | ≤ 1.5 deg @ 1 kHz | ≤ 1° (0.5° typical) @ 50 Hz | ≤ 1° (0.5° typical) @ 50 Hz |
| Bandwidth | 3 A range: 10 Hz to 10 kHz Other ranges: 10 Hz to 20 kHz | 3 A: 10 Hz to 10 kHz Others: 10 Hz to 20 kHz | 2 Hz - 1MHz | 3 A range: 10 Hz to 10 kHz Other ranges: 10 Hz to 20 kHz | 30 A and 300A range: 10 Hz to 10 kHz Other ranges: 10 Hz to 20 kHz |
| TEDS | Not supported | Not supported | Fully supported | Not supported | Not supported |
| Temperature Coefficient | ≤ 0.5 % (0.15 % typical) of output signal per 10 °K | ≤ 0.5 % (0.15 % typical) of output signal per 10 °K | ≤ 0.6 % per 10 °K | ≤ 0.5 % (0.15 % typical) of output signal per 10 °K | ≤ 0.5 % (0.15 % typical) of output signal per 10 °K |
| General Specifications | |||||
| Casing Dimensions [mm] | 120 x 55 x 39 | 120 x 55 x 39 | 140 x 64 x 28 | 120 x 55 x 39 | 120 x 55 x 39 |
| Coil Length | 170 mm | 350 mm | 350 mm | 800 mm | 1200 mm |
| Max. Conductor Size | 45 mm | 100 mm | 100 mm | 235 mm | 360 mm |
| Power Supply | +5 V | +5 V | +9 V | +5 V | +5 V |
| Operating Temperature | - 10 °C to + 55 °C | - 10 °C to + 55 °C | - 10 °C to + 55 °C | - 10 °C to + 55 °C | - 10 °C to + 55 °C |
| Operating Humidity | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C | 0 to 85 % RH decreasing linearly above 35 °C |
| Safety Standards | Class II equipment with double or reinforced insulation between the primary and the secondary (winding connected to the connection cable) as per EN 61010-1 and 61010-2-032 | Class II equipment with double or reinforced insulation between the primary and the secondary (winding connected to the connection cable) as per EN 61010-1 and 61010-2-032 | Class II equipment with double or reinforced insulation between the primary and the secondary (winding connected to the connection cable) as per EN 61010-1 and 61010-2-032 | Class II equipment with double or reinforced insulation between the primary and the secondary (winding connected to the connection cable) as per EN 61010-1 and 61010-2-032 | Class II equipment with double or reinforced insulation between the primary and the secondary (winding connected to the connection cable) as per EN 61010-1 and 61010-2-032 |
| Safety | Sensor: - Type B - 600 V CAT IV / 1,000 V CAT III Casing: - 600 V CAT IV between the terminals and the external enclosure of the casing | Sensor: - Type B - 600 V CAT IV / 1,000 V CAT III Casing: - 600 V CAT IV between the terminals and the external enclosure of the casing | 1,000 V CAT III 600 V CAT IV | 1,000 V CAT III | Sensor: - Type B - 600 V CAT IV / 1,000 V CAT III Casing: - 600 V CAT IV between the terminals and the external enclosure of the casing |
| EMC Standards | EN 61326-1:2013 | EN 61326-1:2013 | IEC 61326:1997 + A1:1998 | EN 61326-1:02-2012 | EN 61326-1:02-2012 |
| PWR-MCTS2 needed | No | No | No | No | No |
| Compatible amplifiers | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 IOLITE LVe | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 *not tested yet with IOLITE and KRYPTON modules | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 *not tested yet with IOLITE and KRYPTON modules |
| Cable length | 2.5 m (Extendable to 10 m upon request) | 2.5 m (Extendable to 10 m upon request) | 2.5 m (Extendable to 10 m upon request) | 2.5 m (Extendable to 10 m upon request) | 2.5 m (Extendable to 10 m upon request) |
| Rev. 23022026 | |||||
| DS-FLEX-CWTUM6-1200A | |||||
| Type | Rogowski coil | ||||
| Peak current | 1200 A | ||||
| Sensitivity | 5 mV/A | ||||
| Accuracy | max. ± 2 % of reading | ||||
| Linearity | 0.05 % of reading | ||||
| DC offset | max. ± 3 mV (@ 25°C) | ||||
| Bandwidth | 3.2 Hz (-3 dB) ... 30 MHz (-3 dB) | ||||
| Noise | max. 10 mVpp | ||||
| TEDS | Supported | ||||
| di/dt | 70 kA/us (peak) 1.2 kA/us (rms) | ||||
| General Specifications | |||||
| Coil Length | 80 mm | ||||
| Coil Cross Section | 1.7 mm | ||||
| Operating Temperature | - 40 °C to + 125 °C | ||||
| Overvoltage protection | 1.2 kVpeak (rating established @ 3 kVrms, 50 Hz, 60 s flash test) | ||||
| PWR-MCTS2 needed | No | ||||
| Compatible amplifiers | SIRIUS LV / HS-LV / XHS-LV SIRIUS STG / HS-STG SIRIUS STGM DEWE 43 | ||||
| Cable length | 1 m | ||||
MCTS-virtalähteen tekniset tiedot
| SIRIUSi-PWR-MCTS2 / SIRIUSir-PWR-MCTS | SIRIUSi-HD-PWR-MCTS2 / SIRIUSir-HD-PWR-MCTS | |
|---|---|---|
| Power supply | 9 - 36 V DC | 9 - 36 V DC |
| Max power consumption | 85 W | 85 W |
| Physical dimensions | 265 x 140 x 65 mm | 265 x 140 x 65 mm |
| Operating temperature | -20 °C to 50 °C | -20 °C to 50 °C |
| Storage temperature | -40 °C to 85 °C | -40 °C to 85 °C |
| Humidity (@ 60 °C) | 95 % RH non-condensing | 95 % RH non-condensing |
| Output | 4 x Isolated Power supply (1500 V DC, 60 sec) | 8 x Isolated Power supply (1500 V DC, 60 sec) |
| Output voltage | ±15 V DC | ±15 V DC |
| Maximum output per channel | 20 W | 20 W |
| Short circuit protection | indefinite (automatic recovery) | indefinite (automatic recovery) |
| Overload protection | 150 % of Iout max. typ | 150 % of Iout max. typ |
DSi-PWR-MCTS-SINGLE
| DSi-PWR-MCTS-SINGLE | |
|---|---|
| Power supply | 9 - 36 V DC |
| Max power consumption | 39 W |
| Power IN connector | Lemo 1B 2-pin male |
| Power OUT connector | Lemo 1B 2-pin female |
| Physical dimensions | 98 x 125 x 32 mm |
| Operating temperature | -20 °C to 50 °C |
| Storage temperature | -40 °C to 85 °C |
| Humidity (@ 60 °C) | 95 % RH non-condensing |
| Output | 1 x Isolated Power supply (1500 V DC, 60 sec) |
| Output voltage | ±15 V DC |
| Maximum output per channel | 39 W |
| Short circuit protection | indefinite (automatic recovery) |
| Overload protection | 150 % of Iout max. typ |
| Sensor connector | D-SUB9 female |
| Amplifier connector | D-SUB9 male |