SIRIUS® XHS Tekniset tiedot

SIRIUS® XHS -järjestelmän tekniset tiedot.
SIRIUS® XHS HybridADC:n tekniset tiedot
SIRIUS® XHS HybridADC -suodatuksen erittelyt
SIRIUS® XHS -digitaalilaskurin tekniset tiedot
SIRIUS® XHS -vahvistimien yleiskatsaus
SIRIUS® XHS ACC -vahvistimen tekniset tiedot
SIRIUS® XHS HV -vahvistimen tekniset tiedot
SIRIUS® XHS LV -vahvistimen tekniset tiedot
SIRIUS® XHS UNI -vahvistimen tekniset tiedot

SIRIUS® XHS -järjestelmän tekniset tiedot.

Power specs
Power Supply	9 - 48 V DC
Power consumption	Typ. 30 W
Environmental
Operating Temperature	-10 to 50 °C
Storage Temperature	-40 to 85 °C
Humidity	5 to 95 % RH non condensing @ 60 °C
IP rating	IP20
Shock & Vibration	Shock (EN 60068-2-27:2009) 75 g, 6 ms, half-sine (25x pos./neg in each axis) Random Vibration (EN 60721-3-2: 1997 - Class 2M2) Sweep sinus Vibration (EN 60068-2-6:2008)
Dimensions	266 mm x 149 mm x 55 mm 266 mm x 149 mm x 69 mm (extended slice)
Weight	2,4 kg
Interfaces
Ethernet	1 GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45)
USB	USB 3.0 (Type C)
CAN	CAN 2.0, CAN-FD (DSUB9)
Sync Input/Ouput
Level (Input/Output)	TTL compatible
Max. Output Current	±24 mA (±50 mA for 1 sec)
Synchronization
Delay between slices	± 1 μs ( to the reference clock )
Max. Sync-cable length	100 m (Master/Slave), 200 m (IRIG)

SIRIUS® XHS HybridADC:n tekniset tiedot

ADC
Type	Hybrid ADC
High bandwidth mode	16 bit SAR, up to 15 MS/s
High dynamic mode	Alias-free up to 2 MS/s
Digital low pass filter	Software selectable (off, alias free)
Analog HW filter	Analog 1 MHz 6th order (Butterworth)
Alias free filter	0.5fs cutoff, 0.45fs pass band, 0.55*fs stop band to -100dB, zero phase distortion, available below 2MS/s

SIRIUS® XHS HybridADC -suodatuksen erittelyt

Filter Mode	High-bandwidth	1 MHz LPF	High-dynamic
Max. SR	15 MS/s	15 MS/s	2 MS/s
SW settings	Off	1 MHz	AAF
Bandwidth (-3 dB)	5 MHz	1 MHz	0.49 fs
Passband frequency (-0.1 dB)	500 kHz	500 kHz	0.45 fs
Passband flatness	± 0.1 dB	± 0.1 dB	± 0.1 dB
Alias-free bandwidth	✗	7.5 MHz	0.45 fs
HW filter	✗	✓	✓
Stopband frequency	✗	7.5 MHz	0.55 fs
Stopband attenuation	✗	-100 dB	-100 dB

SIRIUS® XHS -digitaalilaskurin tekniset tiedot

Counter Input
Input Channels (See 1)	8
Modes	Event counting, waveform timing, encoder, tacho, geartooth, ...
Counter timebase	150 MHz
Time base accuracy	Typical: 0.5 ppm, Max: 2 ppm
Max. Sampling Rate	5 MS/s
Max. Bandwidth	15 MHz
Input Filter	Off, 500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Counter resolution	32-bit
Input Compatibility, Level	3.3 V TTL/CMOS (Low: <0.8 V, High >2 V)
Input termination, impedance	100 kΩ pull-up to +3.3 V
Input Protection	±25 V continuous
Digital Output
Output Channels	8 connectors, 1 line per connector
Output	5 V digital output
Maximum current	32 mA single output, 100 mA total
Output series resistance	50 Ω
Sensor Power Supply
Output Voltage +5 V	5 V +/- 10 % 500 mA typ. Output short protected (Shared between 8 ports)
Output Voltage +12 V (See 2)	12 V +/-10 % 300 mA typ. Output short protected (Shared between 8 ports)
1) Digital inputs on Counter (individual A, B, Z input) can be used only for Trigger condition 2) Maximum 2x DS-TACHO4 laser probes supported.
Rev: 1775113000

SIRIUS® XHS -vahvistimien yleiskatsaus

	XHS-HV	XHS-LV	XHS-ACC	XHS-UNI	XHS-CHG
Connectors	BANANA	DB9, BNC, BANANA	BNC	DB9	BNC
Channels per slice	8	8	8	8	8
Data rate / channel	15 MS/s	15 MS/s	15 MS/s	15 MS/s	15 MS/s
Resolution	16-bit (24-bit @ 2 MS/s)	16-bit (24-bit @ 2 MS/s)	16-bit (24-bit @ 2 MS/s)	16-bit (24-bit @ 2 MS/s)	16-bit (24-bit @ 2 MS/s)
Bandwidth	5 MHz	5 MHz	5 MHz	5 MHz	5 MHz
Voltage ranges	±2000 V ... ±200 V	±100 V ... ±50 mV	±10 V ... ±200 mV	±100 V ... ±50 mV	±10 V ... ±100 mV
Input coupling	DC	DC, AC 1 Hz	DC, AC 0.1 Hz, AC 1 Hz	DC, AC 0.1 Hz, AC 1 Hz
Sensor excitation	✗	2.5..30 V bipolar, 2..24 V unipolar, max. 0.2 A / 2 W	IEPE 2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA	Voltage; Unipolar and Bipolar 0.15 V .. 24 V Current: 100 µA - 100 mA, IEPE	IEPE 2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA
Bridge connection	✗	✗	✗	✓	✗
Programmable shunt	✗	✗	✗	✗	✗
IEPE input	✗	DSI-ACC	✓	✓	✓
Resistance	✗	✗	✗	✓	✗
Temperature (PTx)	✗	DSI-RTD	✗	✓	✗
Thermocouple	✗	DSI-TH	✗	DSI-TH	✗
Potentiometer	✗	✗	✗	✗	✗
LVDT	✗	DSI-LVDT	✗	DSI-LVDT	✗
Charge	✗	DSI-CHG	✗	DSI-CHG	✓
Current	✗	ext. shunt DSI20mA, DSI5A	ext. shunt	ext. shunt DSI20mA, DSI5A	ext. shunt
TEDS	✗	✓	✓	✓	✓
Isolation voltage	CATII 1000 V	420 Vdc (300 Vacrms)	140 Vdc (100 Vacrms)	420 Vdc (300 Vacrms)	100 Vdc (100 Vacrms)
Power consumption per channel (typ.)	1.45 W/ch	1.55 - 5 W/ch	1.8 W/ch	>2 W/ch
Advanced functions	High voltage, high bandwidth, high isolation	High sensor excitation and multi range	Sensor error detection, high speed	Sensor error detection, high speed	High-bandwidth and DC charge
Rev: 1775217600

SIRIUS® XHS ACC -vahvistimen tekniset tiedot

SIRIUSi XHS 8xACC IEPE data acquisition system

Inputs
Input types	Voltage, IEPE
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±10, 5, 2, 1, 0.4 and 0.2 V
Input Accuracy	DC	±0.03 % of reading ±0.02 % of range ±50 μV
	Up to 1 kHz	±0.04 % of reading ±0.02 % of range
	Up to 10 kHz	±0.06 % of reading ±0.05 % of range
	Up to 100 kHz	±0.1 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate, filter \ Range →	10 V	5 V	2 V	1 V	0.4 V	0.2 V
	15 MS/s, Filter off	-85 dB	-84 dB	-83 dB	-82 dB	-77 dB	-72 dB
	1 MS/s, Filter on	-98 dB	-98 dB	-97 dB	-95 dB	-92 dB	-87 dB
	100 kS/s, Filter on	-109 dB	-107 dB	-108 dB	-107 dB	-103 dB	-98 dB
	10 kS/s, Filter on	-119 dB	-119 dB	-119 dB	-118 dB	-114 dB	-109 dB
CMR, Typ.	Frequency \ Range →	10 V	5 V	2 V	1 V	0.4 V	0.2 V
	50 Hz	141 dB	141 dB	139 dB	133 dB	121 dB	120 dB
	400 Hz	130 dB	133 dB	136 dB	137 dB	137 dB	131 dB
	1 kHz	122 dB	125 dB	127 dB	129 dB	130 dB	131 dB
Gain Drift	Typical 10 ppm/K, max. 30 ppm/K
Offset Drift	Typical 0.5 μV/K + 1 ppm of range/K, max. 2 μV/K + 4 ppm of range/K
Gain Linearity	< 0.02 %
Inter Channel Phase-mismatch	0.005° * fin [kHz] + 0.0002°
Channel Cross talk	-145 dB typ. @ 1 kHz
Input Coupling	DC or AC (1 Hz, 0.1 Hz)
Input Impedance	1 MΩ
Overvoltage Protection	50 V continuous; 200 V peak (10 msec)
Max. common mode voltage Isolation voltage	140 Vdc (100 Vacrms)
IEPE mode
Excitation	2 mA, 4 mA, 8 mA, 12 mA, 16 mA, 20 mA
Compliance voltage	24 V
Output Impedance	> 10 kΩ
Sensor detection	Shortcut: < 4 V; Open: > 19 V
Additional Specifications
Input connector	BNC
TEDS support	IEPE mode only
Rev: 1623052800

SIRIUS® XHS HV -vahvistimen tekniset tiedot

Inputs
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±2000 V, ±1000 V, ±400 V, ±200 V
Input Accuracy	Signal frequency	Accuracy
	DC to 1 kHz	±0.03 % of reading ±0.02 % of range
	Up to 10 kHz	±0.1 % of reading ±0.05 % of range
	Up to 100 kHz	±4 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate / Range →	2000 V	1000 V	400 V	200 V
	15 MS/s	-84 dB	-82 dB	-79 dB	-75 dB
	1 MS/s	-95 dB	-93 dB	-85 dB	-78 dB
	100 kS/s	-108 dB	-106 dB	-100 dB	-95 dB
	10 kS/s	-117 dB	-115 dB	-109 dB	-104 dB
CMR, Typ.	101 dB @ 50 Hz, 74 dB @ 400 Hz
Channel Crosstalk	-116 dB typ. @ 50 Hz, -89 dB typ. @ 1 kHz
Gain Drift	Typical 20 ppm/K, max. 40 ppm/K
Offset Drift	Typical 1.5 mV/K + 1 ppm of range/K, max 3 mV/K + 2 ppm of range/K
Gain Linearity	< 0.01 %
Input Coupling	DC
Input Impedance	10 MΩ \| 1 pF
Overvoltage category	CAT II 1000 V
Maximum input voltage	2000 Vdc or 2000 Vpk (1414 Vacrms)
Additional Specifications
Input connector	Banana
Rev: 1698322800

SIRIUS® XHS LV -vahvistimen tekniset tiedot

Inputs	Voltage
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1 MHz (6th order)
Analog bandwidth (-3 dB)	5 MHz
Voltage Mode
Ranges	±100, 50, 20, 10, 5, 2.5, 1, 0.5, 0.25, 0.1 and 0.05 V
Input Accuracy	DC	±0.03 % of reading ±0.02 % of range ±100 μV (2 mV for Ranges ≥ 10 V)
	Up to 1 kHz	±0.03 % of reading ±0.02 % of range
	Up to 10 kHz	±0.1 % of reading ±0.05 % of range
	Up to 100 kHz	±2 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Noise floor, Typ.	Sample rate, filter \ Range →	100 V	5 V	0.5 V	0.05 V
	15 MS/s, Filter off	-82 dB	-78 dB	-65 dB	-51 dB
	1 MS/s, Filter on	-94 dB	-95 dB	-88 dB	-69 dB
	100 kS/s, Filter on	-104 dB	-105 dB	-100 dB	-81 dB
	10 kS/s, Filter on	-113 dB	-114 dB	-107 dB	-87 dB
CMR, Typ.	Frequency \ Range →	100 V	5 V	0.5 V	0.05 V
	50 Hz	91 dB	102 dB	98 dB	100 dB
	400 Hz	86 dB	75 dB	90 dB	98 dB
	10 kHz	66 dB	74 dB	82 dB	83 dB
Channel Crosstalk	Range ≥ 10 V: -105 dB @ 10 kHz Range < 10 V: -120 dB @ 10 kHz
Gain Drift	Typical 10 ppm/K, max. 30 ppm/K
Offset Drift	Range ≥ 10 V: Typ. 100 μV/K + 1 ppm of range/K, Max 250 μV/K + 2 ppm of range/K Range < 10 V: Typ. 4 μV/K + 1 ppm of range/K, Max 8 μV/K + 2 ppm of range/K
Gain Linearity	< 0.03 %
Input Coupling (see 1)	DC, AC 1 Hz
Input Impedance	Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ \| 110 pF between INx to GND
Overvoltage Protection	Range ≥ 10 V: 300 V continuous Range < 10 V: 100 V (200 V peak for 10 msec)
Max. common mode voltage Isolation voltage	420 Vdc (300 Vacrms)
Excitation Voltage
Polarity	Unipolar or Bipolar Software selectable (programmable 16-bit DAC)
Excitation Level	Unipolar 1 .. 24 V; Predefined levels: 1, 2, 2.5, 5, 10, 12, 15, 20 and 24 VDC
Excitation Level	Bipolar 2.5 .. 30 V; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC
Drift	±10 ppm/K ±150 μV/K
Stability 10% to 90% load (bipolar)	< 0.01 %
Current limit	200 mA (2 Watt max. per Channel, 12 Watt max. per Slice)
Additional Specifications
Input connector	DSUB 9, BNC, Banana (others on request)
TEDS support	Standard + DSI® adapters
Rev: 1701403200
1) In- must be within ±10 V referred to GND (iso); for Ranges ≥ 10 V the DC value of In- is not rejected

SIRIUS® XHS UNI -vahvistimen tekniset tiedot

SIRIUSi XHS 8xUNI data acquisition system with universal inputs

Inputs
Input types	Voltage Full / Half / Quarter bridge strain (120 Ω and 350 Ω) Potentiometer, RTD, Resistance Current (ext. Shunt) IEPE
ADC Type	Hybrid ADC - alias free up to 2 MS/s, 16-bit up to 15 MS/s
Sampling Rate	Simultaneous 15 MS/s
Filtering	AAF 1MHz (6th order Butterworth)
Analog bandwidth	5 MHz
Voltage Mode
Ranges	±100, 50, 20, 10, 5, 2.5, 1, 0.5, 0.25, 0.1 and 0.05 V
Input Accuracy	Signal frequency	Accuracy
	DC	±0.03 % of reading ±0.025 % of range ±40 μV (1 mV for Ranges ≥ 10 V)
	Up to 1 kHz	±0.03 % of reading ±0.02 % of range
	Up to 10 kHz	±0.1 % of reading ±0.05 % of range
	Up to 100 kHz	±2 % of reading ±0.1 % of range
	Up to 1000 kHz	±5 % of reading ±0.5 % of range
Typ. Noise floor	Sample rate, filter \ Range →	100 V	5 V	0.5 V	0.05 V
	15 MS/s, Filter off	-81 dB	-81 dB	-75 dB	-56 dB
	1 MS/s, Filter on	-94 dB	-94 dB	-84 dB	-64 dB
	100 kS/s, Filter on	-104 dB	-105 dB	-100 dB	-81 dB
	10 kS/s, Filter on	-113 dB	-114 dB	-107 dB	-88 dB
Typical CMR	Frequency \ Range →	100 V	5 V	0.5 V	0.05 V
	50 Hz	83 dB	92 dB	100 dB	100 dB
	400 Hz	82 dB	91 dB	89 dB	88 dB
	10 kHz	67 dB	77 dB	77 dB	77 dB
Gain Drift	Typical 15 ppm/K, Max. 30 ppm/K
Offset Drift	Range < 10 V: Typ. 1 μV/K + 2 ppm of range/K, Max 4 μV/K + 8 ppm of range/K Range ≥ 10 V: Typ. 50 μV/K + 2 ppm of range/K, Max. 150 μV/K + 6 ppm of range/K
Gain Linearity	< 0.01 %
Inter channel phase mismatch	0.005° * fin [kHz] + 0.0002°
Channel Cross talk	Range ≥ 10 V: -100 dB @ 10 kHz Range < 10 V: -140 dB @ 10 kHz
Input Coupling	DC AC 0.15 Hz for all ranges
Input Impedance	Range < 10 V: > 1 GΩ; Range ≥ 10 V: 1 MΩ \| 110 pF between INx to GND
Overvoltage Protection	Range ≥ 10 V: 300 V continuous Range < 10 V: 100 V (200 V peak for 10 ms)
Max. common mode voltage Isolation voltage	420 Vdc (300 Vacrms)
Excitation Voltage
Polarity	Unipolar or Bipolar Software selectable (programmable 16-bit DAC)
Excitation Level	Unipolar and Bipolar 0.15 V .. 24 V; Predefined levels: 1, 2, 5, 10, 12, 15, 20 and 24 V
Accuracy	±0.05 % ±2 mV
Drift	±10 ppm/K ±100 μV/K
Load stability 0 % to 100 % load	< 0.01 %
Line regulation over 20 Ω of change	< 0.005 % @ 120 Ω load
Noise @ 10 Volt / 350 Ω	< 300 μVrms @ 10 kHz BW
Impedance Sense to Exc Sense to GND	100 kΩ (0.5 Ohm with internal excitation sense) > 100 MΩ
Current limit	100 mA (max. 800 mW)
Protection	Continuous short to ground
Excitation Current
Excitation Current	Free programmable (16-bit DAC)
Ranges	100 µA - 1 mA	1 mA - 20 mA	20 mA - 100 mA
Accuracy	±0.2 % ±0.5 μA	±0.15 % ±2 μA	±0.01 % ±40 μA
Drift	15 ppm/K	15 ppm/K	20 ppm/K
Output Impedance	> 1 MΩ
Bridge Connection Types
Bridge types	Full / Half / Quarter bridge (3-wire or 4-wire) / Quarter Constant Current (2-wire or 4-wire)
Ranges	2 mV/V…1000 mV/V free programmable
Internal Bridge Completion	½ bridge and ¼ bridge 120 Ω and 350 Ω
Bridge Completion Accuracy	0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor	59.88 kΩ and 175 kΩ, software selectable (others on request)
Typ. Shunt Resistor Accuracy	0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset Adjust	Software selectable
Lead-wire compensation	Automatic
IEPE mode
IEPE Current	Free programmable (16-bit DAC)
Predefined levels	2, 4, 8, 12, 16 and 20 mA
Compliance voltage	24 V
Output Impedance	> 1 MΩ
Sensor detection	Shortcut: < 4 V; Open: > 19 V
Additional Specifications
Input connector	DSUB-9 (others on request)
TEDS support	Class 1 (IEPE) and Class 2
DSI® adapters support	Yes
Rev: 1767686300