OBSIDIAN® tekniset tiedot

OBSIDIAN®-järjestelmien yleiskatsaus

SystemOBSIDIAN-R8OBSIDIAN-R8wOBSIDIAN-R12
Number of slots8812
Synchronization2x SYNC on L00B4f (IRIG-B) GPS PPS IEEE 1588v2 synchronization (PTP) (RJ45)2x SYNC on L00B4f (IP67) (IRIG-B) GPS PPS IEEE 1588v2 synchronization (PTP) (RJ45)2x SYNC on L00B4f (IRIG-B) GPS PPS IEEE 1588v2 synchronization (PTP) (RJ45)
Sync Accuracy< 200 ns within same EtherCAT chain < 10 µs using sync for multiple EtherCAT chains below 1 sample to Sirius®< 200 ns within same EtherCAT chain < 10 µs using sync for multiple EtherCAT chains below 1 sample to Sirius®< 200 ns within same EtherCAT chain < 10 µs using sync for multiple EtherCAT chains below 1 sample to Sirius®
Ethernet Interface
Interface type1x Gigabit Ethernet (RJ45)1x Gigabit Ethernet RJ45, 1xWLAN1x Gigabit Ethernet RJ45
Dual EtherCAT® interface
Number of busesTwo (both with buffered DAQ or real time)Two (both with buffered DAQ or real time)Two (both with buffered DAQ or real time)
Data RateDual 100 Mbit bus speedDual 100 Mbit bus speedDual 100 Mbit bus speed
Max. Throughput per ChainFrom 6 MB/s to 10 MB/sFrom 6 MB/s to 10 MB/sFrom 6 MB/s to 10 MB/s
Bus 1 connectors2x Lemo 1B2x Lemo 1TOBSIDIANr: 2× Ethernet RJ45 OBSIDIANr-L: 2× Lemo 1T
Bus 2 connectors2x Ethernet RJ452x Ethernet RJ452x Ethernet RJ45
Minimum delay (analog input to EtherCAT® bus)70 µs70 µs70 µs
Minimum EtherCAT® cycle time100 µs100 µs100 µs
Other Interfaces
Device protocolsOPC-UA XCP over Ethernet openDAQ (see 2)OPC-UA XCP over Ethernet openDAQ (see 2)OPC-UA XCP over Ethernet openDAQ (see 2)
CAN bus
Number of ports222
Interface typeCAN 2.0B, up to 1 MBit/secCAN 2.0B, up to 1 MBit/secCAN 2.0B, up to 1 MBit/sec
Special applicationsCCP, OBDII, J1939, CAN output (also on RT)CCP, OBDII, J1939, CAN output (also on RT)CCP, OBDII, J1939, CAN output (also on RT)
Galvanic isolationIsolated (only on isolated motherboard)Functional isolationFunctional isolation
Bus pin fault protection±36 VFrom –27 V to 40 V From –27 V to 40 V
ESD protection8 kV±4 kV±4 kV
Sensor supply5 V (max. 1.2 W)5 V (max. 1.2 W) / 12 V (max. 1 W)5 V (max. 1.2 W) / 12 V (max. 1 W)
Options
GPSExternal GNSS via USB-C interfaceIntegrated - 10Hz update rate GPS L1, SBAS L1, QZSS L1, GLONASS L1OF, BeiDou B1l, Galileo E1 External GNSS via USB-C interfaceIntegrated - 10Hz update rate (optional) GPS L1, SBAS L1, QZSS L1, GLONASS L1OF, BeiDou B1l, Galileo E1 External GNSS via USB-C interface
Internals
CPU typeARMARMARM
Operating systemLinuxLinuxLinux
SoftwareDewesoft RTDewesoft RTDewesoft RT
Internal storage4 GB eMMC4 GB eMMC4 GB eMMC (max. 32 GB eMMC)
Expandable storageSD card up to 2 TB, USB-C 3.0 Type external storage SD card up to 2 TB, USB-C 3.0 Type external storage SD card up to 2 TB, USB-C 3.0 Type external storage
Power
Power supplyDual redundant 9 - 48 V DCDual redundant 9 - 48 V DCDual redundant 9 - 48 V DC
Power consumption5.8 W @ 24 V (without modules)Typ. 7.2 W (Max. 11 W)OBSIDIAN-R12: Typ 7 W, Max. 11 W IOLITE-RACK (Incl. OBSIDIAN-R12): Typ 15.5 W, Max. 19 W
EtherCAT Bus 1 maximum output10 A10 A10 A
Environmental
Operating Temperature-10 to 50 °C (-40 to 85 °C optional) (see 1)-40 to 60 °C (-40 to 85 °C optional) (see 1)-10 to 50 °C (-40 to 85 °C optional ) (see 1)
Storage Temperature-40 to 85 °C-40 to 85 °C-40 to 85 °C
Humidity5 to 95 % RH non-condensing at 50 °C5 to 95 % RH non-condensing at 50 °C5 to 95 % RH non-condensing at 50 °C
IP ratingIP40IP67IP30
Physical
Dimensions282 x 145 x 144 mm322 x 162 x 155 mm483 x 148 x 133 mm
Weight2.4 kg3.6 kgIOLITE-RACK: 2.85 kg OBSIDIAN-R12 GATE: 500g OBSIDIAN-R12 GATE-L: 520g
1) Extended operating temperature range depends of module configuration
2) OBSIDIAN devices are openDAQ compliant. The full support will be available with a FW upgrade.

OBSIDIAN R8 -järjestelmän tekniset tiedot

SystemOBSIDIAN-R8
Number of slots8
Ethernet Interface
Interface typeGigabit Ethernet
ConnectorRJ-45
Dual EtherCAT® interface
Number of busesTwo (both with buffered DAQ or real time)
Data RateDual 100 Mbit bus speed
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s
Bus 1 connectors2x Lemo 1B
Bus 2 connectors2x Ethernet RJ45
Minimum delay (analog input to EtherCAT® bus)70 µs
Minimum EtherCAT® cycle time100 µs
CAN bus
Number of ports2
Interface typeCAN 2.0B, up to 1 MBit/sec
Special applicationsCCP, OBDII, J1939, CAN output
Galvanic isolationIsolated (only on isolated motherboard)
Bus pin fault protection±36 V
ESD protection8 kV
Internals
CPU typeARM
Operating systemLinux
SoftwareDewesoft RT
Internal storage4 GB eMMC
Expandable storageSD card up to 2 TB, USB-C 3.0 Type external storage
Power
Power supplyDual redundant 9 - 48 V DC
Power consumption5.8 W @ 24 V (without modules)
EtherCAT Bus 1 maximum output10 A
Environmental
Operating Temperature-10 to 50 °C (-40 to 85 °C optional) (see 1)
Storage Temperature-40 to 85 °C
Humidity5 to 95 % RH non-condensing at 50 °C
IP ratingIP40
Physical
Dimensions282 x 145 x 144 mm
Weight2.4 kg
1) Extended operating temperature range depends of module configuration

OBSIDIAN® R8w -järjestelmän tekniset tiedot

SystemOBSIDIAN-R8w
Number of slots8
Ethernet Interface
Interface typeGigabit Ethernet
ConnectorRJ45
Dual EtherCAT® interface
Number of busesTwo (both with buffered DAQ or real time)
Data RateDual 100 Mbit bus speed
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s
Bus 1 connectors2x Lemo 1T
Bus 2 connectors2x Ethernet RJ45
Minimum delay (analog input to EtherCAT® bus)70 µs
Minimum EtherCAT® cycle time100 µs
CAN bus
Number of ports2
Interface typeCAN 2.0B, up to 1 MBit/sec
Special applicationsCCP, OBDII, J1939, CAN output
Isolation Functional isolation
Bus pin fault protectionFrom –27 V to 40 V
ESD protection±4 kV
Sensor supply5 V (max. 1.2 W) / 12 V (max. 1 W)
GPS
Supported navigation systemsGPS L1, SBAS L1, QZSS L1, GLONASS L1OF, BeiDou B1l, Galileo E1
Position accuracy2.5 m
Position accuracy SBAS2 m
Velocity accuracy0.05 m/s
Heading accuracy0.3 degres
Output data rate10 Hz
Hot start1s
Internals
CPU typeARM
Operating systemLinux
SoftwareDewesoft RT
Internal storage4 GB eMMC
Expandable storageSD card up to 2 TB, USB-C 3.0 Type external storage
WiFi, BluetoothWifi supported in Acces mode and client mode Bluetooth software support missing
Power
Power supplyDual redundant 9 - 48 V DC
Power consumptionTyp. 7.2 W (Max. 11 W)
EtherCAT Bus 1 maximum output10 A
Environmental
Operating Temperature-40 to 60 °C (-40 to 85 °C optional) (see 1)
Storage Temperature-40 to 85 °C
Humidity5 to 95 % RH non-condensing at 50 °C
IP ratingIP67
ShockShock: SIST EN 60068-2-27:2009 50 g, 6 ms, half-sine 75 g, 6 ms, half-sine 25x pos./neg in each axis 300x total
VibrationRandom: Profile breakpoints: 24 Hz - 0.04 g²/Hz 60 Hz - 0.5 g²/Hz 100 Hz - 0.5 g²/Hz 240 Hz - 0.01 g²/Hz 2 kHz - 0.01 g²/Hz Profile RMS / Peak = 15 g / 45 g 4 hrs in each axis, 12 hrs total
Physical
Dimensions322 x 162 x 155 mm
Weight3.6 kg
1) Extended operating temperature range depends of module configuration

OBSIDIAN® R12 -järjestelmän tekniset tiedot

SystemOBSIDIAN-R12
Number of slots12
Ethernet Interface
Interface typeGigabit Ethernet
ConnectorRJ45
Dual EtherCAT® interface
Number of busesTwo (both with buffered DAQ or real time)
Data RateDual 100 Mbit bus speed
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s
Bus 1 connectorsOBSIDIAN-R12: 2× Ethernet RJ45 OBSIDIAN-R12-L: 2× Lemo 1T
Bus 2 connectors2x Ethernet RJ45
Minimum delay (analog input to EtherCAT® bus)70 µs
Minimum EtherCAT® cycle time100 µs
CAN bus
Number of ports2
Interface typeCAN 2.0B, up to 1 MBit/s
Special applicationsCCP, OBDII, J1939, CAN output
Isolation Functional isolation
Bus pin fault protectionFrom –27 V to 40 V
ESD protection±4 kV
Sensor supply5 V (max. 1.2 W) / 12 V (max. 1 W)
GPS
Supported navigation systemsGPS L1, SBAS L1, QZSS L1, GLONASS L1OF, BeiDou B1l, Galileo E1
Position accuracy2.5 m
Position accuracy SBAS2 m
Velocity accuracy0.05 m/s
Heading accuracy0.3 degres
Output data rate10 Hz
Hot start1s
Internals
CPU typeARM
Operating systemLinux
SoftwareDewesoft RT
Internal storage4 GB eMMC (max. 32 GB eMMC)
Expandable storageSD card up to 2 TB, USB-C 3.0 Type external storage
WiFi, BluetoothSoftware support missing
Power
Power supplyDual redundant 9 - 48 V DC
Power consumptionOBSIDIAN-R12: Typ 7 W, Max. 11 W IOLITE-RACK (Incl. OBSIDIAN-R12): Typ 15.5 W, Max. 19 W
EtherCAT Bus 1 maximum output10 A
Environmental
Operating Temperature-10 to 50 °C (-40 to 85 °C optional ) (see 1)
Storage Temperature-40 to 85 °C
Humidity5 to 95 % RH non-condensing at 50 °C
IP ratingIP30
ShockShock (EN 60068-2-27:2009)
VibrationVibration random (MIL-STD-810D) Vibration random (EN 60721-3-2: 1997 - Class 2M2)
Physical
Dimensions483 x 148 x 133 mm
WeightIOLITE-RACK: 2.85 kg OBSIDIAN-R12 (4× RJ45): 500 g OBSIDIAN-R12-L (2× LEMO, 2× RJ45): 470g
1) Extended operating temperature range depends of module configuration
Rev:

IOLITE®-monikanavavahvistinmoduulien yleiskatsaus

6xSTG8xSTGS8xLV8xLVe16xLV4xHV8xLA8xACC8xTH8xTH-HS8xRTD8xRTD-HS8xRTDp¹ 32xDI32xDO¹8xDI-4xDO¹4xCNT16xAO²4xCAN-FD¹
ConnectorsDSUB-9Terminal block, DSUB-37BNC, Terminal blockTerminal block, DSUB-37Terminal blockBanana plugBNC, Terminal blockBNCMINI TCMINI TCL0B6f, Terminal blockL0B6f, Terminal blockL0B6fTerminal blockTerminal blockTerminal blockL1B7fTerminal blockD-SUB9
Channels per module6x8x8x8x16x4x8x8x8x8x8x8x8x32x32x8x digital in, 4x digital out4x16x4x
Data rate per channel IOLITE20 kS/s20 kS/s20 kS/s20 kS/s20 kS/s40 kS/s20 kS/s40 kS/s100 S/s100 S/s, upgradable to 10 kS/s100 S/s100 S/s, upgradable to 10 kS/s 100 S/s20 kS/s20 kS/s1 kS/sup to 5 Mbit/s
Data rate per channel OBSIDIAN20 kS/s20 kS/s20 kS/s20 kS/s5 kS/s20 kS/s20 kS/s20 kS/s100 S/s100 S/s, upgradable to 5 kS/s100 S/s100 S/s, upgradable to 5 kS/snot supported10 kS/snot supportednot supported20 kS/s1 kS/snot supported
Resolution24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bitdigitaldigitaldigital100 MHz timebase 5 ppm, 20 ppm max16-bitDigital
Bandwidth0.49*fs0.433*fs0.49*fs0.433*fs0.433*fs0.433*fs0.49*fs0.433*fs0.49*fs (max. 1 kHz)0.49*fs (max. 1 kHz)10 MHz
Voltage mode ranges±50 V, ±10 V, ±1 V, ±100 mV±100 V, ±10 V (±10 V, ±1 V on request)±100 V, ±5 V±200 V, ±10 V±2000 V, ±1000 V, ±400 V, ±200 V±10 V, ±5 V, ±1 V, ±200 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mVopen collectorTTL (Low: <0.8 V, High > 2 V)±10 V
Input couplingDC, AC 1 HzDCDCDCDCDCDCDC, AC 1 Hz, AC 0.1 HzDCDCDCDCDC
Sensor excitation0..24 V (unipolar), 0..12 V (bipolar), 0..44 mA (current), max. 0.55 W/ch1 V, 2 V, 5 V0...24V (unipolar)2 mA, 4 mA, 6 mA244 uA / 440 uA150 uA / 400 uA0.4 mA / 2 mA5 V, 12 V5 V (max. 240 mA), 12 V (max. 100 mA)
Bridge connectionFull, ½, ¼ 350 Ω, ¼ 120 Ω 3-wireFull, ½, ¼ 350 Ω, ¼ 120 Ω 3-wire, 4-wire (optional)
Programmable shunt100 kΩ100 kΩ
IEPE inputDSI-ACC
Resistance1 kΩ, 10 kΩ1 kΩ, 10 kΩ100 Ω, 1 kΩ, 10 kΩ
Temperature (PTx)DSI-RTDPT100, 200, 500, 1000, 2000PT100, 200, 500, 1000, 2000PT100, 200, 500, 1000, 2000
ThermocoupleDSI-THK, J, T, R, S, N, E, C, BK, J, T, R, S, N, E, C, B
Current20 mA (internal shunt), DSI-5A, DSIi-10A, DSIi-20A±20 mA, ±2 mA
Potentiometer
LVDTDSI-LVDT
ChargeDSI-CHG
TEDS✓ (except DB37)
Isolation voltageDifferentialDifferential450 V250 V250 VCATII 1000 V450 V250V1000 V1000 V1000 V1000 V150 V1000 V1000 V1000 VCATII 150 V
Isolation arrangementNoneCh-GNDCh-Ch & Ch-GNDCh-GNDCh-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-GND, groups of 8 ch.Ch-GND, groups of 8 ch.Ch-GND, group of 4/8 chCh-GNDCh-GNDCh-Ch & Ch-GND
Power consumption per moduleTyp. 5.4 W, Max. 11.1 W Typ. 2.7 W, Max. 5.1 WTyp. 2.4 W, Max. 3.5 WTyp. 3.3 W Max. 4.2 WTyp. 3.4 W, Max. 4.2 WTyp. 2.6 W Max. 3 WTyp. 2.4 W, Max. 3.5 WTyp. 4.5 W, Max. 6 W 3.2 WTyp. 2.6 W, Max. 3.4 WTyp. 2.1 W, Max. 2.7 WTyp. 3.5 W Max. 4.3 WTyp. 2.1 W, Max. 2.7 WTyp. 1.2 W, Max. 1.9 WTyp. 1.2 W, Max. 2.0 WTyp. 1.1 W, Max. 1.8 WTyp. 1.9 WTyp. 4.3 W, Max. 7.2 WTyp. 2.5 W Max. 10.5 W
Waterproof version✓ (IP67)✓ (IP67)✓ (IP67)✓ (IP65)✓ (IP67)
Passive PoE functionality✓³✓³✓³✓³✓³
Advanced functionsSupports all strain types, high input rangeSupports all strain types, low power consumptionHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeIEPE, supports TEDS, high channel densityHigh isolation, support of main TC typesHigh isolation, support of main TC typesHigh isolationHigh isolationPulsed excitation, Cryogenic temperature range, High isolationWatchdogHigh sink current, watchdogSupercounter technologySignal conditioningCAN bus, Isolated
¹ Not supported on the OBSIDIAN ² Third party ECAT master Data rate = 1 kS/s ³ Available for devices produced after September 2024.
Rev: 1701068400

IOLITE-8xACC:n tekniset tiedot

Analog inputs
Input typeVoltage, IEPE
Number of channels8
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling Rate IOLITESimultaneous 40 kS/sec per channel (software-selectable)
Sampling Rate OBSIDIANSimultaneous 20 kS/sec per channel (software-selectable)
Voltage Mode
Ranges±10 V±5 V±1 V±0.2 V
Input AccuracyDC±0.02 % of reading ±0.02 % of range
Noise floor, Typ.10 kS/s-116 dB-116 dB-114 dB-105 dB
Dynamic Range, Typ.10 kS/s-151 dB-151 dB-150 dB-140 dB
CMR, Typ. @ 40 kS/s0 dBFS sine wave @ 50 Hz113 dB113 dB111 dB102 dB
0 dBFS sine wave @ 400 Hz112 dB112 dB110 dB102 dB
0 dBFS sine wave @ 1 kHz109 dB108 dB108 dB102 dB
THD, Typ.40 kS/s, -1 dBFS sine wave @ 1 kHz-104 dB-104 dB-104 dB-102 dB
SFDR, Typ.40 kS/s, -1 dBFS sine wave @ 1 kHz106 dB106 dB99 dB96 dB
Gain Linearity< 0.02 %
Gain DriftTyp. 5 ppm/K (Max. 15 ppm/K)
Offset DriftTyp. 0.5 μV/K + 0.5 ppm of range/K (Max. 2 μV/K + 2 ppm of range/K)
Channel Cross talk, Typ. @ 1 kHz-140 dB-140 dB-140 dB-130 dB
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Isolation voltage250 Vpeak channel to ground
Analog input performance
Sampling rateSR < 5 kS/sSR ≥ 5 kS/s
Bandwidth (-3 dB)0.49*fs0.433*fs
Alias-free BandwidthDC to 0.44*fsDC to 0.499*fs
Alias Rejection-105 dB
Delay Through ADC34 / fs
Oversampling128
IEPE input
Excitation2 mA, 4 mA, 6 mA
Compliance voltage28 V
Output Impedance>50 kΩ
Sensor detectionShortcut: <4 V; Open: >19 V
Additional Specifications
RackIOLITEr-8xACC
Input connectorBNC
TEDs supportIEPE mode only (Class 1)
Power supply9 - 48 V DC
Power ConsumptionAnalog input only: Typ. 3.6 W (Max. 4 W) IEPE: Typ. 4.8 W @ 4 mA (Max. 6 W @ 6 mA)
Weight320 g
Slice Dimensions128.4 x 127.6 x 30.1 mm
Additional Specifications
ModularIOLITE-8xACC
Input connectorBNC
TEDs supportIEPE mode only (Class 1)
Power supply9 - 48 V DC
Power ConsumptionAnalog input only: Typ. 3.7 W (Max. 4.5 W) IEPE: Typ. 4.9 W @ 4 mA (Max. 6.4 W @ 6 mA)
Weight575 g
Slice Dimensions136.75 x 127.2 x 35.0 mm
Rev: 1681991028

IOLITE-6xSTG:n tekniset tiedot

Analog inputs
Input typeVoltage Full / half / quarter bridge strain Current Potentiometer Resistance
Number of channels6
ADC Type24-bit SAR with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±50 V±10 V±1 V±100 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS-100 dB-110 dB-130 dB-145 dB
Typical Noise floor @ 10 kS-103 dB-97 dB-103 dB-94 dB
Typical CMR @ 400 Hz / 1 kHz71 dB / 66 dB72 dB / 66 dB96 dB / 88 dB96 dB / 87 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02%
Input CouplingDC, AC 1Hz
Input ImpedanceRange ≥ 10 V; 1 MΩ between IN+ and IN- Range < 10 V: 20 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Current Mode
Ranges20 mA2 mA
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor50 Ω
Analog input performance
Bandwidth (-3 dB)0.49*fs
Alias-free BandwidthDC to 0.453*fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation Voltage
Excitation VoltageFree programmable (16-bit DAC)
Predefined LevelsBipolar: 0, 1, 2, 5, 10 and 12 VDC Unipolar: 0, 2, 5, 10, 15, 24 VDC
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load< 0.01 %
Current Limit42 mA (550 mW max. power)
ProtectionContinuous short to ground
Excitation Current
Excitation CurrentFree programmable (16-bit DAC)
Predefined Levels0, 2, 4, 8, 16, 44 mA
Accuracy±0.1 % ±2 μA (<10 mA), ±0.5 % ±5 μA (>10 mA)
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
Input connectorsDSUB-9
TEDS supportStandard + DSI adapters
Power supply9 - 48 V DC
Power Consumption5.4 W, Max. 11.1 W (7.9 W 120 Ω @ 5 V load, 8.8 W 350 Ω @ 10 V load)
Weight340 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1620029200

IOLITE-8xSTGS tekniset tiedot

Analog inputsIOLITE 8xSTGS
Input typeFull / half / quarter bridge strain (3-wire), Potentiometer
Number of channels8
ADC Type24-bit oversampled sigma-delta with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Analog input performance (see 1)
Ranges1 V0.1 V0.02 V
Gain accuracy0.02 % of reading0.02 % of reading0.02 % of reading
Offset accuracy 210 uV30 uV14 uV
Offset Accuracy after Balance Amplifier21 uV3 uV1.4 uV
Typical Noise floor @ 10 kS/s / 1 kS/s / 100 S/s-107 / -114 / -122 dB -99 / -107 / -117 dB -87 / -96 / -108 dB
Typical Dynamic Range @ 10 kS/s / 1 kS/s / 100 S/s-132 / -139 / -145 dB-122 / -132 / -139 dB-112 / -120 / -130 dB
Typ. Crosstalk @ 1 kHz-120 dB-126 dB-114 dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz76 / 74 / 73 dB97 / 90 / 84 dB108 / 91 / 83 dB
Gain DriftTypical 10 ppm/K (max. 20 ppm/K)
Offset DriftTypical 0.03 μV/K + 2.5 ppm of range/K, max 0.1 μV/K + 9 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance>10 MΩ
Overvoltage ProtectionIn+ to In-: 6 V continuous
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation VoltageUnipolar: 1 V, 2 V, 5 V (see 2)
Excitation Accuracy±3 % of set ±50 mV
Sense Accuracy±0.02 % of reading ±0.25 mV
Sense DriftTypical 10 μV/K + 10 ppm of reading/K, max 20 μV/K + 20 ppm of reading/K
Current Limit42 mA
ProtectionContinuous short to ground
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges2 mV/V ... 1000 mV/V free programmable (software ranges)
AccuracyRange \ Excitation1 V2 V5 V
200 mV/V±0.035 % of reading ±210 μV/V±0.028 % of reading ±105 μV/V±0.025 % of reading ±42 μV/V
20 mV/V±0.027 % of reading ±14 μV/V±0.027 % of reading ±15 μV/V±0.024 % of reading ±6 μV/V
2 mV/V±0.027 % of reading ±14 μV/V±0.024 % of reading ±7 μV/V±0.022 % of reading ±2.8 μV/V
Internal Bridge Completion¼ bridge 120 Ω and 350 Ω
Bridge Completion Accuracy±125 µV/V, TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ software selectable to SNS+ or SNS- and In+ or In-
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
RackIOLITEr-8xSTGS
Input connectorsTerminal Block Weidmueller SL 2.50-04DSUB-37
TEDS supportAvailable Not available
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.7 W Max. 5.1 W (120 Ω @ 5 V load)
Weight340 g330 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xSTGS
Input connectorsTerminal Block Weidmueller SL 2.50-04DSUB-37
TEDS supportAvailable Not available
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W; Max. 4.7 W (120 Ω @ 5 V load)
Weight570 g560 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1697547600
1) Voltage ranges are describing the input for the bridge mode and are not supported as voltage mode.
2) Ratiometric method

IOLITE 8xSTGS (v2) tekniset tiedot

Analog inputsIOLITE STGSv2
Input typeFull / half / quarter bridge strain (3-wire, 4-wire), Potentiometer
Number of channels8
ADC Type24-bit oversampled sigma-delta with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±1 V±100 mV±20 mV
Gain accuracy0.02 % of reading0.02 % of reading0.02 % of reading
Offset accuracy 210 uV30 uV14 uV
Typical Noise floor @ 10 kS/s / 1 kS/s / 100 S/s-107 / -114 / -122 dB -99 / -107 / -117 dB -87 / -96 / -108 dB
Typical Dynamic Range @ 10 kS/s / 1 kS/s / 100 S/s-131/ -139/ -144 dB-123/ -133/ -141 dB-111 / -123 / -131 dB
Typ. Crosstalk @ 1 kHz-137dB-131dB-121dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz81 / 80 / 77 dB100 / 92 / 84 dB110 / 91 / 84 dB
Gain DriftTypical 10 ppm/K (max. 20 ppm/K)
Offset DriftTypical 0.03 μV/K + 2.5 ppm of range/K, max 0.1 μV/K + 9 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Overvoltage ProtectionIn+ to In-: 6 V continuous
Analog input performance
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation VoltageUnipolar: 1 V, 2 V, 5 V (see 1)
Excitation Accuracy±3 % of set ±50 mV
Sense Accuracy±0.02 % of reading ±0.25 mV
Sense DriftTypical 10 μV/K + 10 ppm of reading/K, max 20 μV/K + 20 ppm of reading/K
Current Limit42 mA
ProtectionContinuous short to ground
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (4-wire), ¼ bridge strain (3-wire)
Ranges2 mV/V ... 1000 mV/V free programmable (software ranges)
AccuracyRange \ Excitation1 V2 V5 V
200 mV/V±0.035 % of reading ±210 μV/V±0.028 % of reading ±105 μV/V±0.025 % of reading ±42 μV/V
20 mV/V±0.027 % of reading ±14 μV/V±0.027 % of reading ±15 μV/V±0.024 % of reading ±6 μV/V
2 mV/V±0.027 % of reading ±14 μV/V±0.024 % of reading ±7 μV/V±0.022 % of reading ±2.8 μV/V
Internal Bridge Completion¼ bridge 120 Ω and 350 Ω
Bridge Completion Accuracy±125 µV/V, TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ software selectable to SNS+ or SNS- and In+ or In-
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Internal switch configurationsBridge typeSelectable connectionsInternal SW on:Additonal compensation
Full 6 or 4 Wires4 wires SNS + and EXC + & SNS- and EXC -
Half 5 or 3 Wires3 wires SNS + and EXC + & SNS- and EXC -
QB 3WSNS + and EXC + & SNS- and EXC - SNS + and EXC + & SNS- and EXC - Lead wire compensation available
QB 4WSNS + and EXC + SNS + and EXC +
Sensor current measurement
Bridge configurationFull / HalfQB
Current measuring line EXC+ lineR Line
Current limit 50 mAdc
Resolution0.1 mAdc
Additional math caculusResistance, Power
Sample rate 1 Hz
Additional Specifications
RackIOLITEr-8xSTGSv2
Input connectorsTerminal block, DSUB-37
TEDS supportAvailable for Terminal block
Power supply9 - 48 V DC
Power ConsumptionTyp. 3.1 W Max. 6 W (120 Ω @ 5 V load)
Weight340 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xSTGSv2
Input connectorsTerminal block, DSUB-37
TEDS supportAvailable for Terminal block
Power supply9 - 48 V DC
Power ConsumptionTyp. 3.1 W Max. 6 W (120 Ω @ 5 V load)
Weight570 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1671786000
1) Ratiometric method

IOLITEi-8xLV tekniset tiedot

Analog input
Input typeIsolated voltage
Number of channels8
ADC Type24-bit oversampled SAR
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±100 V±10 V
Accuracy±0.03 % of reading ±50 mV±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)91 dB90 dB
Typical noise floor @ 10 kS-105 dB-98 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-91 dB-91 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)93 dB92 dB
Typical IMR @ 400 Hz / 1 kHz98 dB / 90 dB83 dB / 75 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 2 ppm of range/K, Max. 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB)0.49*fs
Alias-free BandwidthDC to 0.453*fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
RackIOLITEir-8xLV
Input ConnectorsBNCTerminal block 2 pole
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.4 W, Max. 3.5 W
Weight310 g270 g
Slice Dimensions128.4 x 127.6 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xLV
Input ConnectorsBNCTerminal block 2 pole
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.7 W, Max. 3.3 W
Weight545 g505 g
Slice Dimensions137 x 115.0 x 35.0 mm
Rev: 1681991028

IOLITE-8xLVe tekniset tiedot

Inputs
Input typesVoltage, Potentiometer, Current (Ext. shunt)
ADC Type24-bit delta-sigma with anti-aliasing filter (-3 dB @ 160 kHz) Butterworth 2nd order
Sampling RateSimultaneous 20 kS/s
Voltage Mode
Ranges±100 V±5 V
Accuracy±0.03 % of reading ±0.02 % of range
Typ. Noise floor @ 10 kS/sec-114 dB-99 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)--103 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)-114 dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz100 dB / 85 dB / 85 dB96 dB / 88 dB / 88 dB
Gain Linearity<0.02 %<0.01 %
Gain DriftTypical 5 ppm/K, Max. 20 ppm/K
Offset DriftTypical 5 ppm of range/K, Max. 10 ppm of range/K
Channel Crosstalk-130 dB
Input CouplingDC
Input Impedance800 kΩ (between In+ and In-)
Max. common mode voltage±200 V
Input Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Isolation250 V functional isolation (channel to power supply ground)
Analog input performance
Bandwidth (-3 dB)0.433*fs
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation voltageUnipolar 2 ... 24V DC
Current limit2.8 W max. power per channel, 22.4 W per slice
Excitation accuracy0.05 % ± 2 mV
Drift±20 ppm/K ± 60 μV/K
Stability 10 % to 90 % load< 0.06 % @ 5 V exc (< 0.01 % @ 24 V exc)
Noise @ 10 V / 350 Ω <150 μVrms @ 10 kS
Line regulation over 10 Ω of change< 0.04 % @ 120 Ω load
ProtectionContinuous short to ground
Additional Specifications
RackIOLITEr-8xLVe
Input connectorTerminal blockDSUB-37
TEDS supportYes
Power supply9 - 48 V DC
Power consumptionAnalog input only: Typ. 3.3 W (Max. 4.2 W) With Excitation: 6.9 W 120 Ω load @ 5 V, 38 W 120 Ω load @ 20 V
Weight310 g300 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xLVe
Input connectorTerminal blockDSUB-37
TEDS supportYes
Power supply9 - 48 V DC
Power consumptionAnalog input only: Typ. 3.3 W (Max. 4.2 W) With Excitation: 6.9 W 120 Ω load @ 5 V, 38 W 120 Ω load @ 20 V
Weight550 g540 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev.: 1721714400

IOLITE-16xLV tekniset tiedot

Analog input
Input typeVoltage
Number of channels16
ADC Type24-bit oversampled sigma-delta
Sampling Rates IOLITESimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Sampling Rates OBSIDIANSimultaneous 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±200 V±10 V
Accuracy±0.03 % of reading ±40 mV±0.03 % of reading ±2 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)103 dB101 dB
Typical noise floor @ 10 kS-115 dB-105 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-93 dB-108 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)95 dB111 dB
Typical CMR @ 400 Hz / 1 kHz88 dB / 87 dB82 dB / 80 dB
Crosstalk @ 1 kHz-118 dB-120 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 2 ppm of range/K, Max. 5 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance800 kΩ
Max. common mode voltage±200 V
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB)0.433*fs
Alias-free BandwidthDC to 0.45*fs (DC to 0.499*fs @ 20 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Additional Specifications
RackIOLITEr-16xLV
Input ConnectorsTerminal block 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Isolation Voltage250 V functional isolation (channel to power supply ground)
Power ConsumptionTyp. 3.4 W (Max. 3.9 W)
Weight230 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
ModularIOLITE-16xLV
Input ConnectorsTerminal block 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Isolation Voltage250 V functional isolation (channel to power supply ground)
Power ConsumptionTyp. 3.6 W (Max. 4.5 W)
Weight530g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1685344484

IOLITEi-4xHV tekniset tiedot

Analog inputsIOLITEi 4xHV
Input typeVoltage
Number of channels4
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling Rate IOLITESimultaneous 40 kS/s per channel (software-selectable)
Sampling Rate OBSIDIANSimultaneous 20 kS/sec per channel (software-selectable)
Anti-aliasing filter -3 dB @ 150 kHz (Butterworth 3rd order)
Voltage mode
Ranges±2000 V±1000 V±400 V±200 V
Input Accuracy±0.03 % of reading ±0.02 % of range
Typ. Dynamic Range @ 10 kS-137 dB-137 dB-137 dB- 132 dB
Typ. Noise floor @ 10 kS-113 dB-112 dB-109 dB-104 dB
Typ. THD (40 kS/s, -6 dBFS sine wave @ 1 kHz)N/AN/AN/A-103 dB
Typ. CMR @ 20 kS/s80 dB @ 50 Hz, 64 dB @ 400 Hz
Gain DriftTypical 10 ppm/K, max. 25 ppm/K
Offset DriftTypical 100 μV/K + 2 ppm of range/K, max 200 μV/K + 4 ppm of range/K
Gain Linearity< 0.02% (2000 V range), < 0.01% (other ranges)
Input CouplingDC
Input Impedance10 MΩ
Overvoltage protectionCAT II 1000 V
Analog input performance
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.45*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Additional Specifications
RackIOLITEir-4xHV
Input connector4mm safety banana jack
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W (max. 3 W)
Weight310 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-4xHV
Input connector4mm safety banana jack
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W (max. 3 W)
Weight575 g
Slice Dimensions136.75 x 127.2 x 35.0 mm
Rev: 1701151200

IOLITEi-8xLA:n tekniset tiedot

Analog input
Input typeIsolated current
Number of channels8
ADC Type24-bit oversampled SAR
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Current Mode
Ranges±20 mA±2 mA
Accuracy±0.05 % of reading ±10 µA±0.05 % of reading ±2 µA
Typical noise floor @ 10 kS/sec-100 dB-100 dB
Crosstalk (20 kS/sec, -1 dBFS @ 1 kHz)-121 dB-128 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 5 ppm of range/K, Max. 15 ppm of range/K
Gain Linearity< 0.05 %
Input CouplingDC
Input Impedance50 Ω
Overvoltage ProtectionIn+ to In-: 30 V continuous
Overcurrent ProtectionIn+ to In-: 70 mA continuous
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.8 W, Max. 3.5 W
Input ConnectorsBNCTerminal block 2 pole
Weight310 g270 g
Slice Dimensions128.4 x 127.6 x 30.1 mm128.4 x 115.4 x 30.1 mm
Rev: 1632117100

IOLITEi-8xTH tekniset tiedot

Inputs
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±100 μV±0.02 % of reading ±10 μV
Typical Noise floor @ 10/100 S/sec-114 dB / -105 dB-109 dB / -100 dB
Gain DriftTypical 4 ppm/K (max. 10 ppm/K)Typical 4 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity<0.01%<0.01%
Input CouplingDCDC
Input Impedance100 MΩ100 MΩ
Temperature Mode
Thermocouple TypesK, J, T, R, S, N, E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±10 μV
Sampling rates10, 20, 40, 80, 100 S/sec
Typical Noise0.007 °C RMS@Type K @ 10 S/sec 0.02 °C RMS@Type K @ 100 S/sec
Additional Specifications
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumption3.2 W
Weight230 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1578677400

IOLITEi-8xTH-HS tekniset tiedot

Inputs
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling Rate IOLITESimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±50 μV±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -110 dB / -100 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007%
Input CouplingDC
Input Impedance100 MΩ
Temperature Mode
Thermocouple TypesK, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
RackIOLITEir-8xTH-HS
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.6 W (Max. 3.4 W)
Weight290 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xTH-HS
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.6 W (Max. 3.8 W)
Weight555 g
Slice Dimensions137 x 115.0 x 35.0 mm
Rev: 1701151200

IOLITEi-8xRTD:n tekniset tiedot

Analog inputs
Input typesVoltage, Resistance or Universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range ±10 μV
Typical Noise floor @ 10/100 s/sec-117 dB / -107 dB-111 dB / -101 dB
Gain DriftTypical 4 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance1 MΩ
Temperature Mode
TypesPT100, PT200, PT500, PT1000, PT2000
Measurement range-200 °C to +850 °C
Accuracy±0.05 % of reading ±0.2 °C
Temperature Drifttyp. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection3-wire or 4-wire
Resistance Mode
Ranges0…10 kΩ0…1 kΩ
Accuracy±0.02 % of reading ±0.01 % of range
Input Connection3-wire or 4-wire
Additional Specifications
RackIOLITEir-8xRTD
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.1 W, Max. 2.7 W
Weight325 g225 g
Dimensions128.4 x 115.4 x 30.1 mm
ModularIOLITEi-8xRTD
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.7 W)
Weight585 g485 g
Dimensions137 x 115.0 x 35.0 mm
Rev: 1727427136

IOLITEi-8xRTD-HS tekniset tiedot

Analog inputs
Input typesVoltage, Resistance or Universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling Rate IOLITESimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN100 S/s
Voltage mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -108 dB / -98 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007 %
Input CouplingDC
Input Impedance10 MΩ
Temperature mode
RangesPT500, PT1000, PT2000PT100, PT200
Excitation current150 uA400 uA
Measurement range-200 °C to +850 °C
Accuracy±0.02 % of reading ±0.2 °C
Temperature DriftTyp. ±2 ppm/K (Max. ±10 ppm/K)
Input Connection3-wire or 4-wire
Resistance mode
Ranges0…10 kΩ0…1 kΩ
Excitation current150 uA400 uA
Accuracy±0.02 % of reading ±0.008 % of range
Input Connection3-wire or 4-wire
Additional Specifications
RackIOLITEir-8xRTD-HS
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.3 W)
Weight325 g225 g
Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xRTD-HS
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.7 W)
Weight585 g485 g
Dimensions137 x 115.0 x 35.0 mm
Rev: 1701151200

IOLITE-4xCNT:n tekniset tiedot

Counter
Number of channels4
Timebase100 MHz
Time base accuracyTypical: 5 ppm, Max: 20 ppm
Max. bandwidth10 MHz
Input Filter500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level CompatibilityTTL (Low: <0.8 V, High >2 V)
Input impedance100 kΩ pull-up to +3.3 V
Input Protection±25 V continuous
Counter modescounting, waveform timing, encoder, gear-tooth sensor
Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 100 mA max. (400 mA to supply 4 channels)
Output Voltage +12 V12 V +/-10 % 50 mA max. (100 mA to supply 4 channels)
IsolationCh to GND isolation
Additional Specifications
Input connector7-pin LEMO 1B series EEG.1B.307.CLNY
Power Consumption @ 24 VTyp. 1.9 W
Power supply9 - 48 V DC
Slice Dimensions128.4 x 115.4 x 30.1 mm

IOLITEi-4xCAN-FD tekniset tiedot

CAN ports specification
Number of ports4
Interface typeCAN-FD, CAN 2.0B
CAN 2.0B data rateUp to 1 Mbit/s (see 1)
CAN-FD data rateUp to 5 Mbit/s (see 1)
Special protocolsJ1939, XCP, OBDII
Galvanic isolationIsolated
Bus pin fault protection±36 V
Power specification
Power supply9 - 48 V DC
Maximum sensor power consumption 5 V / max. 250 mA (1.25 W) 12 V / max. 90 mA (1.1 W)
Maximum power consumption max. 2 W (no load)
Sensor supply isolationChannel to ground
Additional Specifications
RackIOLITEir-4xCAN-FD
Input connectorDSUB9
Power supply9 - 48 V DC
Weight310 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITEi-4xCAN-FD
Input connectorDSUB9
Power supply9 - 48 V DC
Weight550 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
1) For more information please see the manual.
Takaisin alkuun