IOLITE® Modular Технические характеристики

Технические характеристики модульной системы IOLITE®

InterfaceIOLITE Single channelIOLITE Multi channel
Data interfaceEtherCATEtherCAT
Data Rate100 Mbps Full Duplex bus speed100 Mbps Full Duplex bus speed
Sync Accuracy< 200 ns within same EtherCAT chain < 2 µs using sync for multiple EtherCAT chains below 1 sample to Sirius®< 200 ns within same EtherCAT chain < 2 µs using sync for multiple EtherCAT chains below 1 sample to Sirius®
Bus connectorsEthernet RJ45Ethernet RJ45
Max. cable length between devices100 m100 m
Max. Throughput per ChainFrom 6 MB/s to 10 MB/s (see 1)From 6 MB/s to 10 MB/s
Data interface connectionEthernet RJ45, Single cable for data, power and sync, daisy chainableEthernet RJ45, single cable for data, power and sync, daisy chainable (see 2)
Power
Power supply9 V - 48 V9 V - 48 V
Power consumption~2 W (see individual modules)~4 W (see individual modules)
Power supply connector-SCDN-THR 3.81/04/90G 3.2SN BK BX
Environmental
Operating Temperature-20 to 60 °C-40 to 85 °C
Storage Temperature-20 to 60 °C-40 to 85 °C
Humidity95 %, no condensation95 %, no condensation
IP ratingIP20IP20
Physical
Dimensions82 x 62 x 52 mm (might differ for different modules)137 x 119 x 35 (might differ for different modules)
Weight130 g (might differ for different modules)530 g (might differ for different modules)
1) 55 per chain (@ 20 kS/s total sample rate per device), multiple chains possible. Additional power injectors are necessary.
2) Passive PoE is supported only on IOLITE-16xLV, IOLITE-8xSTGS, IOLITEi-8xTH-HS, IOLITEi-8xRTD-HS, IOLITE-8xLVe, IOLITE-8xACC. All other modules have power and data separated. Daisy-chain for data is available with Ethernet RJ45 cable, Daisy-chain for power is available with T3B2m-T3B2m-0.1m cable
Rev: 1668186000

Обзор модулей усилителя IOLITE® One

1xACC1xSTG4xDI4xDO1xAO
ConnectorBNCDB9DSUB15HD maleDSUB15HD femaleBNC
Number of channels per module11441
Data rate per channel40 kS/s40 kS/s20 kS/s
Resolution24-bit24-bitDigitalDigital18-bit
Bandwidth0.49 fs0.49 fs
Voltage ranges±10 V, ±5 V, ±1 V, ±200 mV±50 V, ±10 V, ±1 V, ±100 mVDigital (Low: < 1 V, High: > 2 V)±10 V
Input couplingDC, AC 0.1 Hz, 1 HzDC, AC 1 Hz
Sensor excitationIEPE 4 mA, 8 mAUnipolar 0 - 24 V Bipolar 0 - 12 V
Bridge connectionFull, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire
Programmable shunt100 kΩ
IEPE inputDSI-ACC
Resistance
Temperature (PTx)DSI-RTD
ThermocoupleDSI-TH
Current2 mA, 20 mA (internal shunt)
Potentiometer
LVDTDSI-LVDT
ChargeDSI-CHG
TEDS✓ (IEPE only)
Isolation125 Vrms Isolation CH, GND125 Vrms Isolation CH, GNDCH-CH, GND-GNDCH-GND
Power consumption2W2.5W2.5W2.5W2W
Rev: 1593518446

Обзор многоканальных усилительных модулей IOLITE®

6xSTG8xSTGS8xLV8xLVe16xLV4xHV8xLA8xACC8xTH8xTH-HS8xRTD8xRTD-HS8xRTDp¹ 32xDI32xDO¹8xDI-4xDO¹4xCNT16xAO²4xCAN-FD¹
ConnectorsDSUB-9Terminal block, DSUB-37BNC, Terminal blockTerminal block, DSUB-37Terminal blockBanana plugBNC, Terminal blockBNCMINI TCMINI TCL0B6f, Terminal blockL0B6f, Terminal blockL0B6fTerminal blockTerminal blockTerminal blockL1B7fTerminal blockD-SUB9
Channels per module6x8x8x8x16x4x8x8x8x8x8x8x8x32x32x8x digital in, 4x digital out4x16x4x
Data rate per channel IOLITE20 kS/s20 kS/s20 kS/s20 kS/s20 kS/s40 kS/s20 kS/s40 kS/s100 S/s100 S/s, upgradable to 10 kS/s100 S/s100 S/s, upgradable to 10 kS/s 100 S/s20 kS/s20 kS/s1 kS/sup to 5 Mbit/s
Data rate per channel OBSIDIAN20 kS/s20 kS/s20 kS/s20 kS/s5 kS/s20 kS/s20 kS/s20 kS/s100 S/s100 S/s, upgradable to 5 kS/s100 S/s100 S/s, upgradable to 5 kS/snot supported10 kS/snot supportednot supported20 kS/s1 kS/snot supported
Resolution24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bit24-bitdigitaldigitaldigital100 MHz timebase 5 ppm, 20 ppm max16-bitDigital
Bandwidth0.49*fs0.433*fs0.49*fs0.433*fs0.433*fs0.433*fs0.49*fs0.433*fs0.49*fs (max. 1 kHz)0.49*fs (max. 1 kHz)10 MHz
Voltage mode ranges±50 V, ±10 V, ±1 V, ±100 mV±100 V, ±10 V (±10 V, ±1 V on request)±100 V, ±5 V±200 V, ±10 V±2000 V, ±1000 V, ±400 V, ±200 V±10 V, ±5 V, ±1 V, ±200 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mV±1 V, ±100 mVopen collectorTTL (Low: <0.8 V, High > 2 V)±10 V
Input couplingDC, AC 1 HzDCDCDCDCDCDCDC, AC 1 Hz, AC 0.1 HzDCDCDCDCDC
Sensor excitation0..24 V (unipolar), 0..12 V (bipolar), 0..44 mA (current), max. 0.55 W/ch1 V, 2 V, 5 V0...24V (unipolar)2 mA, 4 mA, 6 mA244 uA / 440 uA150 uA / 400 uA0.4 mA / 2 mA5 V, 12 V5 V (max. 240 mA), 12 V (max. 100 mA)
Bridge connectionFull, ½, ¼ 350 Ω, ¼ 120 Ω 3-wireFull, ½, ¼ 350 Ω, ¼ 120 Ω 3-wire, 4-wire (optional)
Programmable shunt100 kΩ100 kΩ
IEPE inputDSI-ACC
Resistance1 kΩ, 10 kΩ1 kΩ, 10 kΩ100 Ω, 1 kΩ, 10 kΩ
Temperature (PTx)DSI-RTDPT100, 200, 500, 1000, 2000PT100, 200, 500, 1000, 2000PT100, 200, 500, 1000, 2000
ThermocoupleDSI-THK, J, T, R, S, N, E, C, BK, J, T, R, S, N, E, C, B
Current20 mA (internal shunt), DSI-5A, DSIi-10A, DSIi-20A±20 mA, ±2 mA
Potentiometer
LVDTDSI-LVDT
ChargeDSI-CHG
TEDS✓ (except DB37)
Isolation voltageDifferentialDifferential450 V250 V250 VCATII 1000 V450 V250V1000 V1000 V1000 V1000 V150 V1000 V1000 V1000 VCATII 150 V
Isolation arrangementNoneCh-GNDCh-Ch & Ch-GNDCh-GNDCh-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-Ch & Ch-GNDCh-GND, groups of 8 ch.Ch-GND, groups of 8 ch.Ch-GND, group of 4/8 chCh-GNDCh-GNDCh-Ch & Ch-GND
Power consumption per moduleTyp. 5.4 W, Max. 11.1 W Typ. 2.7 W, Max. 5.1 WTyp. 2.4 W, Max. 3.5 WTyp. 3.3 W Max. 4.2 WTyp. 3.4 W, Max. 4.2 WTyp. 2.6 W Max. 3 WTyp. 2.4 W, Max. 3.5 WTyp. 4.5 W, Max. 6 W 3.2 WTyp. 2.6 W, Max. 3.4 WTyp. 2.1 W, Max. 2.7 WTyp. 3.5 W Max. 4.3 WTyp. 2.1 W, Max. 2.7 WTyp. 1.2 W, Max. 1.9 WTyp. 1.2 W, Max. 2.0 WTyp. 1.1 W, Max. 1.8 WTyp. 1.9 WTyp. 4.3 W, Max. 7.2 WTyp. 2.5 W Max. 10.5 W
Waterproof version✓ (IP67)✓ (IP67)✓ (IP67)✓ (IP65)✓ (IP67)
Passive PoE functionality✓³✓³✓³✓³✓³
Advanced functionsSupports all strain types, high input rangeSupports all strain types, low power consumptionHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeHigh isolation, high input rangeIEPE, supports TEDS, high channel densityHigh isolation, support of main TC typesHigh isolation, support of main TC typesHigh isolationHigh isolationPulsed excitation, Cryogenic temperature range, High isolationWatchdogHigh sink current, watchdogSupercounter technologySignal conditioningCAN bus, Isolated
¹ Not supported on the OBSIDIAN ² Third party ECAT master Data rate = 1 kS/s ³ Available for devices produced after September 2024.
Rev: 1701068400

Технические характеристики IOLITEi-1xACC

Analog inputs
Input typesVoltage, IEPE
Number of channels1
Input connectorBNC
ADC Type24-bit SAR with anti-aliasing filter
Sampling Rate40 kS/s (50 kS/s while using it standalone)
Voltage Mode
Ranges±10 V±5 V±1 V±200 mV
Typ. Input Accuracy±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)90 dB90 dB89 dB88 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)113 dB110 dB109 dB106 dB
Typ. Noise floor @ 10 kS/sec-100 dB-99 dB-99 dB-98 dB
Typical CMR @ 400 Hz / 1 kHz130 dB / 120 dB122 dB / 119 dB104 dB / 97 dB90 dB / 84 dB
Gain Drifttyp. 10 ppm/K (max. 40 ppm/K)
Offset Drifttyp. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity< 0.02 %
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Isolation125 Vrms channel to ground isolation
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
IEPE input
Excitation4 mA, 8 mA
Compliance voltage24 V
Sensor detectionShortcut: <4 V; Open: >19 V
TEDS supportIEPE mode only
Power
Power consumption2 W
Environmental
IP ratingIP20
Physical
Dimensions93 x 67 x 28 mm
Weight130 g
Rev: 1593518446

Технические характеристики IOLITEi-1xSTG

Analog input - Voltage
Input typesVoltage, current, full bridge strain, half bridge strain, quarter bridge strain
Number of channels1
Input connectorDB9
ADC Type24-bit SAR with anti-aliasing filter
Sampling Rate40 kS/s
Voltage Mode
Ranges±50 V±10 V±1 V±100 mV
Typ. Input Accuracy±0.03 % of reading ±0.02 % of range ±0.1 mV
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)89 dB88 dB88 dB87 dB
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz)100 dB110 dB130 dB145 dB
Typ. Noise floor @ 10 kS/sec-103 dB-99 dB-103 dB-96 dB
Typical CMR @ 400 Hz / 1 kHz71 dB / 66 dB72 dB / 66 dB96 dB / 88 dB96 dB / 87 dB
Gain Drifttyp. 10 ppm/K (max. 40 ppm/K)
Offset Drifttyp. 0.3 μV/K + 5 ppm of range/K (max. 2 µV/K + 10 ppm of range/K)
Gain Linearity< 0.02 %
Input CouplingDC, AC 1 Hz
Input ImpedanceRange ≥ 10 V; 1 MΩ between IN+ and IN- Range < 10 V: 20 MΩ
Overvoltage ProtectionRange ≥ 10 V; 200 V Range < 10 V: 50 V
Isolation125 Vrms channel to ground isolation
TEDS supportStandard + DSI adapters
Current mode
Current ranges2 mA, 20 mA
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt resistor50 Ω
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation voltage
Excitation voltageFree programmable (16-bit DAC)
Predefined LevelsUnipolar 0 - 24 V, Bipolar 0 - 12 V
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load<0.01 %
Current Limit42 mA (400 mW max. Power)
ProtectionContinuous short to ground
Bridge mode
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3 wire)
Bridge ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 2 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.1 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Power
Power consumption2.5 W
Environmental
IP ratingIP20
Physical
Dimensions82 x 67 x 28 mm
Weight130 g
Rev: 1710761400

Технические характеристики IOLITEi-4xDI

Digital Input
Input typeDigital
Number of channels4
ConnectorDSBU15HD Male
CompatibilityTTL / CMOS Voltage Levels
Input low levelUIN < 1 V
Input high levelUIN > 2 V
Input high current @ 5 V UIN3 mA typ.
Input high current @ 30 V UIN6 mA typ.
Propagation delay< 1 μs
Max. sampling rate40 kS/sec
Overvoltage protection30 V Continuous, 65 V peak
IsolationGalvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 %, 300 mA max.
Output Voltage +12 V12 V +/-10 %, 100 mA max.
Output Voltage +VecatEtherCAT Bus Supply Voltage, 200 mA max.
Power
Power consumption2.5 W
Environmental
IP ratingIP20
Physical
Dimensions82 x 67 x 28 mm
Weight130 g
Rev: 1593518446

Технические характеристики IOLITEi-4xDO

Digital Output
Output typeDigital
Number of channels4
ConnectorDSUB15HD Female
Maximum update ratedepends on EtherCAT master cycle time
Output typeopen collector with active internal pullup to 5 V
Sinkmax 50 V, 2 A (resistive load, unprotected)
Source5 V, max. 40 mA (internally limited)
Max. switching frequency for internal PWM100 kHz
IsolationGalvanic isolation CH, GND
Non-Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 %, 300 mA max. Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Output Voltage +12 V12 V +/-10 %, 100 mA max. Max. combined load on +5 V and +12 V pins: 1.5 W reduced by the load already present on +Vin pin
Output Voltage +VecatEtherCAT Bus Supply Voltage, 200 mA max. (see 1.)
Power
Power consumption2.5 W
Environmental
IP ratingIP20
Physical
Dimensions82 x 67 x 28mm
Weight130 g
Rev: 1593518446

Технические характеристики IOLITEi-3xMEMS-ACC-8g

MEMS Accelerometer
Nr. of axes3
Range±2, ±4, ±8g (software selectable)
Max. sample rate4 kS/s
-3 dB bandwidth (at 4 kS/s sample rate)0 Hz .. 1 kHz
Min.Typ.Max.
Dynamic range96 dB
Noise density (lowest range)25 µg/√Hz
Residual noise (+-2 g range, 50 Hz bandwidth) 100 µg RMS
Residual noise (+-2 g range, 125 Hz bandwidth) 150 µg RMS
Calibrated offset error ±4 mg
Calibrated gain error ±0.2 %
Offset temperature drift (-20 .. 60 degC)-0.15 mg / degC ±0.02 mg / degC0.15 mg / degC
Semsitivity temperature drift (-20 .. 60 degC) ±0.01 % / degC
Linearity error (smallest range)0.1 % FS
Crossaxis sensitivity-1 %1 %
MEMS Inclinometer
Option available
Accuracy and resolution valid in range±15 deg
Relative accuracy (23 degC)0.01 deg
Resolution0.001 deg
Bandwidth<0,1Hz
Update rate of inclination channels1Hz
Digital Temperature Input (only a dedicated temperature sensor is compatible)
Option available
Measurement range-55 to 125 °C
Measurement accuracy+-0.5 °C
IP67 version
Option available

Технические характеристики IOLITEi-3xMEMS-ACC-40g

MEMS Accelerometer
Nr. of axes3
Range±10, ±20, ±40g (software selectable)
Max. sample rate4 kS/s
-3 dB bandwidth (at 4 kS/s sample rate)0 Hz .. 1 kHz
Min.Typ.Max.
Dynamic range96 dB
Noise density (lowest range)75 µg/√Hz
Residual noise (+-2 g range, 50 Hz bandwidth)
Residual noise (+-2 g range, 125 Hz bandwidth)
Calibrated offset error-100 mg30 mg100 mg
Calibrated gain error±0.5 %
Offset temperature drift (-20 .. 60 degC)-0.75 mg / degC±0.2 mg / degC0.75 mg / degC
Semsitivity temperature drift (-20 .. 60 degC)±0.01 % / degC
Linearity error (smallest range)0.1 % FS
Crossaxis sensitivity1 %
MEMS Inclinometer
Option available
Digital Temperature input
Option available
IP67 version
Option available

Технические характеристики IOLITEi-3xMEMS-ACC-S

MEMS Accelerometer
Nr. of axes3
Range±15g
Max. sample rate1 kS/s
-6 dB bandwidth (at 1 kS/s sample rate)0 Hz .. 460 Hz
Min.Typ.Max.
Dynamic range137 dB
Noise density0.7 µg/√Hz
Offser error±4 mg
Offset temperature drift (-20 .. 60 degC) +-0.2 mg / degC
Linearity error -1g ... +1g range0.05 % FS
Crossaxis sensitivity-1 %1 %
MEMS Inclinometer
Option available
Digital Temperature input
Option available
IP67 version
Option available

Технические характеристики IOLITEi-2xMEMS-INC

MEMS Inclinometer
Accuracy and resolution valid in range±15 deg
Relative accuracy (23 degC)0.01 deg
Resolution0.001 deg
Bandwidth<0,1Hz
Update rate of inclination channels1Hz
IP67 version
Option available

IOLITEi-1xMEMS-ACC-Z

MEMS Accelerometer
Nr. of axes1
Range±2, ±4, ±8g (software selectable)
Max. sample rate4 kS/s
-3 dB bandwidth (at 4 kS/s sample rate)0 Hz .. 1 kHz
Min.Typ.Max.
Dynamic range96 dB
Noise density (lowest range)25 µg/√Hz
Residual noise (+-2 g range, 50 Hz bandwidth) 100 µg RMS
Residual noise (+-2 g range, 125 Hz bandwidth) 150 µg RMS
Calibrated offset error ±4 mg
Calibrated gain error ±0.2 %
Offset temperature drift (-20 .. 60 degC)-0.15 mg / degC ±0.02 mg / degC0.15 mg / degC
Semsitivity temperature drift (-20 .. 60 degC) ±0.01 % / degC
Linearity error (smallest range)0.1 % FS
Crossaxis sensitivity-1 %1 %
Digital Temperature Input (only a dedicated temperature sensor is compatible)
Option available
Measurement range-55 to 125 °C
Measurement accuracy+-0.5 °C
IP67 version
Option available

Технические характеристики IOLITE-8xACC

Analog inputs
Input typeVoltage, IEPE
Number of channels8
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling Rate IOLITESimultaneous 40 kS/sec per channel (software-selectable)
Sampling Rate OBSIDIANSimultaneous 20 kS/sec per channel (software-selectable)
Voltage Mode
Ranges±10 V±5 V±1 V±0.2 V
Input AccuracyDC±0.02 % of reading ±0.02 % of range
Noise floor, Typ.10 kS/s-116 dB-116 dB-114 dB-105 dB
Dynamic Range, Typ.10 kS/s-151 dB-151 dB-150 dB-140 dB
CMR, Typ. @ 40 kS/s0 dBFS sine wave @ 50 Hz113 dB113 dB111 dB102 dB
0 dBFS sine wave @ 400 Hz112 dB112 dB110 dB102 dB
0 dBFS sine wave @ 1 kHz109 dB108 dB108 dB102 dB
THD, Typ.40 kS/s, -1 dBFS sine wave @ 1 kHz-104 dB-104 dB-104 dB-102 dB
SFDR, Typ.40 kS/s, -1 dBFS sine wave @ 1 kHz106 dB106 dB99 dB96 dB
Gain Linearity< 0.02 %
Gain DriftTyp. 5 ppm/K (Max. 15 ppm/K)
Offset DriftTyp. 0.5 μV/K + 0.5 ppm of range/K (Max. 2 μV/K + 2 ppm of range/K)
Channel Cross talk, Typ. @ 1 kHz-140 dB-140 dB-140 dB-130 dB
Input CouplingDC, AC 0.1 Hz, 1 Hz
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Isolation voltage250 Vpeak channel to ground
Analog input performance
Sampling rateSR < 5 kS/sSR ≥ 5 kS/s
Bandwidth (-3 dB)0.49*fs0.433*fs
Alias-free BandwidthDC to 0.44*fsDC to 0.499*fs
Alias Rejection-105 dB
Delay Through ADC34 / fs
Oversampling128
IEPE input
Excitation2 mA, 4 mA, 6 mA
Compliance voltage28 V
Output Impedance>50 kΩ
Sensor detectionShortcut: <4 V; Open: >19 V
Additional Specifications
RackIOLITEr-8xACC
Input connectorBNC
TEDs supportIEPE mode only (Class 1)
Power supply9 - 48 V DC
Power ConsumptionAnalog input only: Typ. 3.6 W (Max. 4 W) IEPE: Typ. 4.8 W @ 4 mA (Max. 6 W @ 6 mA)
Weight320 g
Slice Dimensions128.4 x 127.6 x 30.1 mm
Additional Specifications
ModularIOLITE-8xACC
Input connectorBNC
TEDs supportIEPE mode only (Class 1)
Power supply9 - 48 V DC
Power ConsumptionAnalog input only: Typ. 3.7 W (Max. 4.5 W) IEPE: Typ. 4.9 W @ 4 mA (Max. 6.4 W @ 6 mA)
Weight575 g
Slice Dimensions136.75 x 127.2 x 35.0 mm
Rev: 1681991028

Технические характеристики IOLITE-6xSTG

Analog inputs
Input typeVoltage Full / half / quarter bridge strain Current Potentiometer Resistance
Number of channels6
ADC Type24-bit SAR with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±50 V±10 V±1 V±100 mV
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±0.1 mV
Typical Dynamic Range @ 10 kS-100 dB-110 dB-130 dB-145 dB
Typical Noise floor @ 10 kS-103 dB-97 dB-103 dB-94 dB
Typical CMR @ 400 Hz / 1 kHz71 dB / 66 dB72 dB / 66 dB96 dB / 88 dB96 dB / 87 dB
Gain DriftTypical 10 ppm/K (max. 40 ppm/K)
Offset DriftTypical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K
Gain Linearity< 0.02%
Input CouplingDC, AC 1Hz
Input ImpedanceRange ≥ 10 V; 1 MΩ between IN+ and IN- Range < 10 V: 20 MΩ
Overvoltage ProtectionIn+ to In-: 50 V continuous, 200 V peak (10 msec)
Current Mode
Ranges20 mA2 mA
Input Accuracy±0.03 % of reading, ±0.02 % of range, ±2.1 μA
Internal Shunt Resistor50 Ω
Analog input performance
Bandwidth (-3 dB)0.49*fs
Alias-free BandwidthDC to 0.453*fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Excitation Voltage
Excitation VoltageFree programmable (16-bit DAC)
Predefined LevelsBipolar: 0, 1, 2, 5, 10 and 12 VDC Unipolar: 0, 2, 5, 10, 15, 24 VDC
Accuracy±0.05 % ±2 mV
Drift±50 ppm/K ±100 μV/K
Stability 10 % to 90 % Load< 0.01 %
Current Limit42 mA (550 mW max. power)
ProtectionContinuous short to ground
Excitation Current
Excitation CurrentFree programmable (16-bit DAC)
Predefined Levels0, 2, 4, 8, 16, 44 mA
Accuracy±0.1 % ±2 μA (<10 mA), ±0.5 % ±5 μA (>10 mA)
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges2…1000 mV/V free programmable
Internal Bridge Completion½ bridge and ¼ bridge 120 and 350 Ω
Bridge Completion Accuracy0.05 %; TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ (others on request)
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
Input connectorsDSUB-9
TEDS supportStandard + DSI adapters
Power supply9 - 48 V DC
Power Consumption5.4 W, Max. 11.1 W (7.9 W 120 Ω @ 5 V load, 8.8 W 350 Ω @ 10 V load)
Weight340 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1620029200

Технические характеристики IOLITE-8xSTGS

Analog inputsIOLITE 8xSTGS
Input typeFull / half / quarter bridge strain (3-wire), Potentiometer
Number of channels8
ADC Type24-bit oversampled sigma-delta with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Analog input performance (see 1)
Ranges1 V0.1 V0.02 V
Gain accuracy0.02 % of reading0.02 % of reading0.02 % of reading
Offset accuracy 210 uV30 uV14 uV
Offset Accuracy after Balance Amplifier21 uV3 uV1.4 uV
Typical Noise floor @ 10 kS/s / 1 kS/s / 100 S/s-107 / -114 / -122 dB -99 / -107 / -117 dB -87 / -96 / -108 dB
Typical Dynamic Range @ 10 kS/s / 1 kS/s / 100 S/s-132 / -139 / -145 dB-122 / -132 / -139 dB-112 / -120 / -130 dB
Typ. Crosstalk @ 1 kHz-120 dB-126 dB-114 dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz76 / 74 / 73 dB97 / 90 / 84 dB108 / 91 / 83 dB
Gain DriftTypical 10 ppm/K (max. 20 ppm/K)
Offset DriftTypical 0.03 μV/K + 2.5 ppm of range/K, max 0.1 μV/K + 9 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance>10 MΩ
Overvoltage ProtectionIn+ to In-: 6 V continuous
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation VoltageUnipolar: 1 V, 2 V, 5 V (see 2)
Excitation Accuracy±3 % of set ±50 mV
Sense Accuracy±0.02 % of reading ±0.25 mV
Sense DriftTypical 10 μV/K + 10 ppm of reading/K, max 20 μV/K + 20 ppm of reading/K
Current Limit42 mA
ProtectionContinuous short to ground
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (3-wire)
Ranges2 mV/V ... 1000 mV/V free programmable (software ranges)
AccuracyRange \ Excitation1 V2 V5 V
200 mV/V±0.035 % of reading ±210 μV/V±0.028 % of reading ±105 μV/V±0.025 % of reading ±42 μV/V
20 mV/V±0.027 % of reading ±14 μV/V±0.027 % of reading ±15 μV/V±0.024 % of reading ±6 μV/V
2 mV/V±0.027 % of reading ±14 μV/V±0.024 % of reading ±7 μV/V±0.022 % of reading ±2.8 μV/V
Internal Bridge Completion¼ bridge 120 Ω and 350 Ω
Bridge Completion Accuracy±125 µV/V, TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ software selectable to SNS+ or SNS- and In+ or In-
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Additional Specifications
RackIOLITEr-8xSTGS
Input connectorsTerminal Block Weidmueller SL 2.50-04DSUB-37
TEDS supportAvailable Not available
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.7 W Max. 5.1 W (120 Ω @ 5 V load)
Weight340 g330 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xSTGS
Input connectorsTerminal Block Weidmueller SL 2.50-04DSUB-37
TEDS supportAvailable Not available
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W; Max. 4.7 W (120 Ω @ 5 V load)
Weight570 g560 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1697547600
1) Voltage ranges are describing the input for the bridge mode and are not supported as voltage mode.
2) Ratiometric method

Технические характеристики IOLITE 8xSTGS (v2)

Analog inputsIOLITE STGSv2
Input typeFull / half / quarter bridge strain (3-wire, 4-wire), Potentiometer
Number of channels8
ADC Type24-bit oversampled sigma-delta with anti-aliasing filter
Sampling RateSimultaneous 20 kS/s per channel (software-selectable)
Voltage Mode
Ranges±1 V±100 mV±20 mV
Gain accuracy0.02 % of reading0.02 % of reading0.02 % of reading
Offset accuracy 210 uV30 uV14 uV
Typical Noise floor @ 10 kS/s / 1 kS/s / 100 S/s-107 / -114 / -122 dB -99 / -107 / -117 dB -87 / -96 / -108 dB
Typical Dynamic Range @ 10 kS/s / 1 kS/s / 100 S/s-131/ -139/ -144 dB-123/ -133/ -141 dB-111 / -123 / -131 dB
Typ. Crosstalk @ 1 kHz-137dB-131dB-121dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz81 / 80 / 77 dB100 / 92 / 84 dB110 / 91 / 84 dB
Gain DriftTypical 10 ppm/K (max. 20 ppm/K)
Offset DriftTypical 0.03 μV/K + 2.5 ppm of range/K, max 0.1 μV/K + 9 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Overvoltage ProtectionIn+ to In-: 6 V continuous
Analog input performance
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation VoltageUnipolar: 1 V, 2 V, 5 V (see 1)
Excitation Accuracy±3 % of set ±50 mV
Sense Accuracy±0.02 % of reading ±0.25 mV
Sense DriftTypical 10 μV/K + 10 ppm of reading/K, max 20 μV/K + 20 ppm of reading/K
Current Limit42 mA
ProtectionContinuous short to ground
Bridge measurement
Bridge Connection Typesfull bridge strain, ½ bridge strain, ¼ bridge strain (4-wire), ¼ bridge strain (3-wire)
Ranges2 mV/V ... 1000 mV/V free programmable (software ranges)
AccuracyRange \ Excitation1 V2 V5 V
200 mV/V±0.035 % of reading ±210 μV/V±0.028 % of reading ±105 μV/V±0.025 % of reading ±42 μV/V
20 mV/V±0.027 % of reading ±14 μV/V±0.027 % of reading ±15 μV/V±0.024 % of reading ±6 μV/V
2 mV/V±0.027 % of reading ±14 μV/V±0.024 % of reading ±7 μV/V±0.022 % of reading ±2.8 μV/V
Internal Bridge Completion¼ bridge 120 Ω and 350 Ω
Bridge Completion Accuracy±125 µV/V, TCR: 5 ppm/K (others on request)
Internal Shunt Resistor100 kΩ software selectable to SNS+ or SNS- and In+ or In-
Shunt Resistor Accuracy0.05 %; TCR: 10 ppm/K (others on request)
Input Short, Sensor Offset AdjustSoftware-selectable
Internal switch configurationsBridge typeSelectable connectionsInternal SW on:Additonal compensation
Full 6 or 4 Wires4 wires SNS + and EXC + & SNS- and EXC -
Half 5 or 3 Wires3 wires SNS + and EXC + & SNS- and EXC -
QB 3WSNS + and EXC + & SNS- and EXC - SNS + and EXC + & SNS- and EXC - Lead wire compensation available
QB 4WSNS + and EXC + SNS + and EXC +
Sensor current measurement
Bridge configurationFull / HalfQB
Current measuring line EXC+ lineR Line
Current limit 50 mAdc
Resolution0.1 mAdc
Additional math caculusResistance, Power
Sample rate 1 Hz
Additional Specifications
RackIOLITEr-8xSTGSv2
Input connectorsTerminal block, DSUB-37
TEDS supportAvailable for Terminal block
Power supply9 - 48 V DC
Power ConsumptionTyp. 3.1 W Max. 6 W (120 Ω @ 5 V load)
Weight340 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xSTGSv2
Input connectorsTerminal block, DSUB-37
TEDS supportAvailable for Terminal block
Power supply9 - 48 V DC
Power ConsumptionTyp. 3.1 W Max. 6 W (120 Ω @ 5 V load)
Weight570 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1671786000
1) Ratiometric method

Технические характеристики IOLITEi-8xLV

Analog input
Input typeIsolated voltage
Number of channels8
ADC Type24-bit oversampled SAR
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±100 V±10 V
Accuracy±0.03 % of reading ±50 mV±0.03 % of reading ±5 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)91 dB90 dB
Typical noise floor @ 10 kS-105 dB-98 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-91 dB-91 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)93 dB92 dB
Typical IMR @ 400 Hz / 1 kHz98 dB / 90 dB83 dB / 75 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 2 ppm of range/K, Max. 10 ppm of range/K
Gain Linearity< 0.02 %
Input CouplingDC
Input Impedance1 MΩ
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB)0.49*fs
Alias-free BandwidthDC to 0.453*fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
RackIOLITEir-8xLV
Input ConnectorsBNCTerminal block 2 pole
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.4 W, Max. 3.5 W
Weight310 g270 g
Slice Dimensions128.4 x 127.6 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xLV
Input ConnectorsBNCTerminal block 2 pole
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.7 W, Max. 3.3 W
Weight545 g505 g
Slice Dimensions137 x 115.0 x 35.0 mm
Rev: 1681991028

Технические характеристики IOLITE-8xLVe

Inputs
Input typesVoltage, Potentiometer, Current (Ext. shunt)
ADC Type24-bit delta-sigma with anti-aliasing filter (-3 dB @ 160 kHz) Butterworth 2nd order
Sampling RateSimultaneous 20 kS/s
Voltage Mode
Ranges±100 V±5 V
Accuracy±0.03 % of reading ±0.02 % of range
Typ. Noise floor @ 10 kS/sec-114 dB-99 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)--103 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)-114 dB
Typ. CMR @ 50 Hz / 400 Hz / 1 kHz100 dB / 85 dB / 85 dB96 dB / 88 dB / 88 dB
Gain Linearity<0.02 %<0.01 %
Gain DriftTypical 5 ppm/K, Max. 20 ppm/K
Offset DriftTypical 5 ppm of range/K, Max. 10 ppm of range/K
Channel Crosstalk-130 dB
Input CouplingDC
Input Impedance800 kΩ (between In+ and In-)
Max. common mode voltage±200 V
Input Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Isolation250 V functional isolation (channel to power supply ground)
Analog input performance
Bandwidth (-3 dB)0.433*fs
Alias-free BandwidthDC to 0.499*fs (DC to 0.44*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Excitation Voltage
Excitation voltageUnipolar 2 ... 24V DC
Current limit2.8 W max. power per channel, 22.4 W per slice
Excitation accuracy0.05 % ± 2 mV
Drift±20 ppm/K ± 60 μV/K
Stability 10 % to 90 % load< 0.06 % @ 5 V exc (< 0.01 % @ 24 V exc)
Noise @ 10 V / 350 Ω <150 μVrms @ 10 kS
Line regulation over 10 Ω of change< 0.04 % @ 120 Ω load
ProtectionContinuous short to ground
Additional Specifications
RackIOLITEr-8xLVe
Input connectorTerminal blockDSUB-37
TEDS supportYes
Power supply9 - 48 V DC
Power consumptionAnalog input only: Typ. 3.3 W (Max. 4.2 W) With Excitation: 6.9 W 120 Ω load @ 5 V, 38 W 120 Ω load @ 20 V
Weight310 g300 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITE-8xLVe
Input connectorTerminal blockDSUB-37
TEDS supportYes
Power supply9 - 48 V DC
Power consumptionAnalog input only: Typ. 3.3 W (Max. 4.2 W) With Excitation: 6.9 W 120 Ω load @ 5 V, 38 W 120 Ω load @ 20 V
Weight550 g540 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev.: 1721714400

Технические характеристики IOLITE-16xLV

Analog input
Input typeVoltage
Number of channels16
ADC Type24-bit oversampled sigma-delta
Sampling Rates IOLITESimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Sampling Rates OBSIDIANSimultaneous 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Voltage Mode
Ranges±200 V±10 V
Accuracy±0.03 % of reading ±40 mV±0.03 % of reading ±2 mV
Typ. SNR (10 kS/s, -1 dBFS sine wave @ 1 kHz)103 dB101 dB
Typical noise floor @ 10 kS-115 dB-105 dB
Typ. THD (10 kS/s, -1 dBFS sine wave @ 1 kHz)-93 dB-108 dB
Typ. SFDR (10 kS/s, -1 dBFS sine wave @ 1 kHz)95 dB111 dB
Typical CMR @ 400 Hz / 1 kHz88 dB / 87 dB82 dB / 80 dB
Crosstalk @ 1 kHz-118 dB-120 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 2 ppm of range/K, Max. 5 ppm of range/K
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance800 kΩ
Max. common mode voltage±200 V
Overvoltage ProtectionIn+ to In-: 200 V continuous, 350 Vpeak (100 ms)
Analog input performance
Bandwidth (-3 dB)0.433*fs
Alias-free BandwidthDC to 0.45*fs (DC to 0.499*fs @ 20 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Additional Specifications
RackIOLITEr-16xLV
Input ConnectorsTerminal block 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Isolation Voltage250 V functional isolation (channel to power supply ground)
Power ConsumptionTyp. 3.4 W (Max. 3.9 W)
Weight230 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
ModularIOLITE-16xLV
Input ConnectorsTerminal block 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Isolation Voltage250 V functional isolation (channel to power supply ground)
Power ConsumptionTyp. 3.6 W (Max. 4.5 W)
Weight530g
Slice Dimensions136.75 x 115.0 x 35.0 mm
Rev: 1685344484

Технические характеристики IOLITEi-4xHV

Analog inputsIOLITEi 4xHV
Input typeVoltage
Number of channels4
ADC Type24-bit delta-sigma with anti-aliasing filter
Sampling Rate IOLITESimultaneous 40 kS/s per channel (software-selectable)
Sampling Rate OBSIDIANSimultaneous 20 kS/sec per channel (software-selectable)
Anti-aliasing filter -3 dB @ 150 kHz (Butterworth 3rd order)
Voltage mode
Ranges±2000 V±1000 V±400 V±200 V
Input Accuracy±0.03 % of reading ±0.02 % of range
Typ. Dynamic Range @ 10 kS-137 dB-137 dB-137 dB- 132 dB
Typ. Noise floor @ 10 kS-113 dB-112 dB-109 dB-104 dB
Typ. THD (40 kS/s, -6 dBFS sine wave @ 1 kHz)N/AN/AN/A-103 dB
Typ. CMR @ 20 kS/s80 dB @ 50 Hz, 64 dB @ 400 Hz
Gain DriftTypical 10 ppm/K, max. 25 ppm/K
Offset DriftTypical 100 μV/K + 2 ppm of range/K, max 200 μV/K + 4 ppm of range/K
Gain Linearity< 0.02% (2000 V range), < 0.01% (other ranges)
Input CouplingDC
Input Impedance10 MΩ
Overvoltage protectionCAT II 1000 V
Analog input performance
Bandwidth (-3 dB)0.433*fs (0.49*fs < 5 kS/s)
Alias-free BandwidthDC to 0.499*fs (DC to 0.45*fs @ < 5 kS/s)
Alias Rejection-105 dB (all sample rates)
Delay Through ADC34 / fs
Oversampling128
Additional Specifications
RackIOLITEir-4xHV
Input connector4mm safety banana jack
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W (max. 3 W)
Weight310 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-4xHV
Input connector4mm safety banana jack
Power supply9 - 48 V DC
Power ConsumptionTyp. 2.6 W (max. 3 W)
Weight575 g
Slice Dimensions136.75 x 127.2 x 35.0 mm
Rev: 1701151200

Технические характеристики IOLITEi-8xLA

Analog input
Input typeIsolated current
Number of channels8
ADC Type24-bit oversampled SAR
Sampling RatesSimultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/s (software-selectable)
Current Mode
Ranges±20 mA±2 mA
Accuracy±0.05 % of reading ±10 µA±0.05 % of reading ±2 µA
Typical noise floor @ 10 kS/sec-100 dB-100 dB
Crosstalk (20 kS/sec, -1 dBFS @ 1 kHz)-121 dB-128 dB
Gain DriftTypical 10 ppm/K, Max. 40 ppm/K
Offset DriftTypical 5 ppm of range/K, Max. 15 ppm of range/K
Gain Linearity< 0.05 %
Input CouplingDC
Input Impedance50 Ω
Overvoltage ProtectionIn+ to In-: 30 V continuous
Overcurrent ProtectionIn+ to In-: 70 mA continuous
Analog input performance
Bandwidth (-3 dB)0.49 fs
Alias-free BandwidthDC to 0.453 fs
Alias Rejection-100 dB (all sample rates)
Delay Through ADC37 / fs
Oversampling32
Additional Specifications
Power supply9 - 48 V DC
Isolation Voltage450 Vpeak channel to ground & channel to channel
Power ConsumptionTyp. 2.8 W, Max. 3.5 W
Input ConnectorsBNCTerminal block 2 pole
Weight310 g270 g
Slice Dimensions128.4 x 127.6 x 30.1 mm128.4 x 115.4 x 30.1 mm
Rev: 1632117100

Технические характеристики IOLITEi-8xTH

Inputs
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±100 μV±0.02 % of reading ±10 μV
Typical Noise floor @ 10/100 S/sec-114 dB / -105 dB-109 dB / -100 dB
Gain DriftTypical 4 ppm/K (max. 10 ppm/K)Typical 4 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity<0.01%<0.01%
Input CouplingDCDC
Input Impedance100 MΩ100 MΩ
Temperature Mode
Thermocouple TypesK, J, T, R, S, N, E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±10 μV
Sampling rates10, 20, 40, 80, 100 S/sec
Typical Noise0.007 °C RMS@Type K @ 10 S/sec 0.02 °C RMS@Type K @ 100 S/sec
Additional Specifications
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumption3.2 W
Weight230 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1578677400

Технические характеристики IOLITEi-8xTH-HS

Inputs
Input typeIsolated universal thermocouple and voltage
Number of channels8
ADC Type24-bit delta-sigma
Sampling Rate IOLITESimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±50 μV±0.02 % of reading ±7 μV
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -110 dB / -100 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007%
Input CouplingDC
Input Impedance100 MΩ
Temperature Mode
Thermocouple TypesK, J, T, R, S, N , E, C, B
Accuracy±0.02 % of reading ±0.5 °C ±7 μV
Typical Noise0.002 °C RMS @ Type K @ 10 S/s 0.006 °C RMS @ Type K @ 100 S/s 0.02 °C RMS @ Type K @ 1 kS/s 0.05 °C RMS @ Type K @ 10 kS/s
Additional Specifications
RackIOLITEir-8xTH-HS
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.6 W (Max. 3.4 W)
Weight290 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xTH-HS
Input connectorsMini Thermocouple connector (copper)
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.6 W (Max. 3.8 W)
Weight555 g
Slice Dimensions137 x 115.0 x 35.0 mm
Rev: 1701151200

Технические характеристики IOLITEi-8xRTD

Analog inputs
Input typesVoltage, Resistance or Universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range ±10 μV
Typical Noise floor @ 10/100 s/sec-117 dB / -107 dB-111 dB / -101 dB
Gain DriftTypical 4 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity< 0.01 %
Input CouplingDC
Input Impedance1 MΩ
Temperature Mode
TypesPT100, PT200, PT500, PT1000, PT2000
Measurement range-200 °C to +850 °C
Accuracy±0.05 % of reading ±0.2 °C
Temperature Drifttyp. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection3-wire or 4-wire
Resistance Mode
Ranges0…10 kΩ0…1 kΩ
Accuracy±0.02 % of reading ±0.01 % of range
Input Connection3-wire or 4-wire
Additional Specifications
RackIOLITEir-8xRTD
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.1 W, Max. 2.7 W
Weight325 g225 g
Dimensions128.4 x 115.4 x 30.1 mm
ModularIOLITEi-8xRTD
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.7 W)
Weight585 g485 g
Dimensions137 x 115.0 x 35.0 mm
Rev: 1727427136

Технические характеристики IOLITEi-8xRTD-HS

Analog inputs
Input typesVoltage, Resistance or Universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling Rate IOLITESimultaneous 10, 20, 40, 50, 80, 100, 200, 500, 1k, 2k, 5k, 10k S/s (optional)
Sampling Rate OBSIDIAN100 S/s
Voltage mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range
Typical Noise Floor @ 10 / 100 / 1k / 10k S/s-130 dB / -120 dB / -110 dB / -104 dB-120 dB / -108 dB / -98 dB / -90 dB
Offset DriftTyp. 0.05 μV/K (Max. 0.2 μV/K)Typ. 0.01 μV/K (Max. 0.1 μV/K)
Gain DriftTyp. 2 ppm/K (Max. 10 ppm/K)
Gain Linearity< 0.007 %
Input CouplingDC
Input Impedance10 MΩ
Temperature mode
RangesPT500, PT1000, PT2000PT100, PT200
Excitation current150 uA400 uA
Measurement range-200 °C to +850 °C
Accuracy±0.02 % of reading ±0.2 °C
Temperature DriftTyp. ±2 ppm/K (Max. ±10 ppm/K)
Input Connection3-wire or 4-wire
Resistance mode
Ranges0…10 kΩ0…1 kΩ
Excitation current150 uA400 uA
Accuracy±0.02 % of reading ±0.008 % of range
Input Connection3-wire or 4-wire
Additional Specifications
RackIOLITEir-8xRTD-HS
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.3 W)
Weight325 g225 g
Dimensions128.4 x 115.4 x 30.1 mm
Additional Specifications
ModularIOLITEi-8xRTD-HS
Input connectorsLemo 0B 6pin EEA.0B.306.CLNTerminal Block Weidmueller SL 2.50-04
Isolation voltage1000 Vpeak channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 3.5 W (Max. 4.7 W)
Weight585 g485 g
Dimensions137 x 115.0 x 35.0 mm
Rev: 1701151200

Технические характеристики IOLITEi-8xRTDp

Analog inputs
Input typesVoltage, resistor or universal PTxxx inputs
Number of channels8
ADC Type24-bit delta-sigma
Sampling RateSimultaneous 100 S/s
Voltage Mode
Ranges±1 V±100 mV
Input Accuracy±0.02 % of reading ±0.01 % of range ±10 μV±0.02 % of reading ±0.01 % of range ±10 μV
Typical Noise floor @ 10/100 s/sec-117 dB / -107 dB-111 dB / -101 dB
Gain DriftTypical 4 ppm/K (max. 10 ppm/K)Typical 4 ppm/K (max. 10 ppm/K)
Offset DriftTypical 0.05 μV/K (max. 0.2 μV/K)Typical 0.05 μV/K (max. 0.2 μV/K)
Gain Linearity< 0.01 %< 0.01 %
Input CouplingDCDC
Input Impedance1 MΩ1 MΩ
Temperature Mode
RangesPT200, PT500, PT1000, PT2000PT100
Excitation current0.4 mA or ±0.4 mA2 mA or ±2 mA
Excitation typeDC or square wave from 5 Hz to 50 HzDC or square wave from 5 Hz to 50 Hz
Measurement range-200 °C to +850 °C-200 °C to +850 °C
Accuracy±0.05 % of reading ±0.2 °C±0.05 % of reading ±0.2 °C
Temperature Drifttyp. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)typ. ±5 ppm/K (max. ±12 ppm/K ±0.003 °C/K)
Input Connection2-wire or 4-wire2-wire or 4-wire
Resolution< 0.001 °C< 0.001 °C
Resistance Mode
Ranges0…10 kΩ0…1 kΩ0…100 Ω
Excitation current0.4 mA or ±0.4 mA2 mA or ±2 mA2 mA or ±2 mA
Excitation type (See 1)DC or square wave from 5 Hz to 50 HzDC or square wave from 5 Hz to 50 HzDC or square wave from 5 Hz to 50 Hz
Accuracy±0.02 % of reading ±0.01 % of range±0.02 % of reading ±0.01 % of range±0.02 % of reading ±0.01 % of range
Input Connection2-wire or 4-wire2-wire or 4-wire2-wire or 4-wire
Additional Specifications
Input connectorsLemo 0B 6pin EEA.0B.306.CLN
Isolation voltage210 Vdc or 150 Vacrms channel to ground & channel to channel
Power supply9 - 48 V DC
Power consumptionTyp. 2.1 W, Max. 2.7 W
Weight330 g
Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1667583000
1) The frequency of the square wave is related to the SR/2.

Технические характеристики IOLITE-32xDI

Digital Input
Isolated Input Channels32
Input low level-1 V ~ +1 V
Input high level-48 V ~ -3 V, +3 V ~ +48 V
Input high current @ 5 VUIN < 1 mA
Input high current @ 30 VUIN < 1 mA
Sampling rateSimultaneous 20 kS/s
Overvoltage protection100 V continuous (250 Vpeak)
Isolation voltage peak1000 V Isolated common GND, groups of 8 ch
Additional Specifications
Input connectorsTerminal block, 2 pole, 4 x 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Power outmax. 2 A (unprotected)
Power consumptionTyp. 1.2 W, Max. 1.9 W
Weight220 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1668186000

Технические характеристики IOLITE-4xCNT

Counter
Number of channels4
Timebase100 MHz
Time base accuracyTypical: 5 ppm, Max: 20 ppm
Max. bandwidth10 MHz
Input Filter500 ns, 1 μs, 2 μs, 4 μs, 5 μs and 7.5 μs
Input Level CompatibilityTTL (Low: <0.8 V, High >2 V)
Input impedance100 kΩ pull-up to +3.3 V
Input Protection±25 V continuous
Counter modescounting, waveform timing, encoder, gear-tooth sensor
Isolated Sensor Power Supply
Output Voltage +5 V5 V +/- 10 % 100 mA max. (400 mA to supply 4 channels)
Output Voltage +12 V12 V +/-10 % 50 mA max. (100 mA to supply 4 channels)
IsolationCh to GND isolation
Additional Specifications
Input connector7-pin LEMO 1B series EEG.1B.307.CLNY
Power Consumption @ 24 VTyp. 1.9 W
Power supply9 - 48 V DC
Slice Dimensions128.4 x 115.4 x 30.1 mm

Технические характеристики IOLITE-32xDO

Digital Output¹
Isolated Output Channels32
CompatibilitySolid state relay
Maximum sink current0.5 A
Maximum switching voltage50 V
Maximum update ratedepending on EtherCAT master
Isolation voltage peak1000 V Isolated common GND, groups of 8 ch
Additional Specifications
Input connectorsTerminal block, 2 pole, 4 x 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Power outmax. 2 A (unprotected)
Power consumptionTyp. 1.2 W, Max. 2.0 W
Weight230 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
¹ Not supported on the OBSIDIAN
Rev: 1668186000

Технические характеристики IOLITE-8xDI-4xDO

Digital Input
Isolated Input Channels8
Input low level-1 V ~ +1 V
Input high level-48 V ~ -3 V, +3 V ~ +48 V
Input high current @ 5 VUIN < 1 mA
Input high current @ 30 VUIN < 1 mA
Sampling rateSimultaneous 40 kS/s
Overvoltage protection100 V continuous (250 Vpeak)
Isolation voltage peak1000 V Isolated common GND
Digital Output¹
Isolated Output Channels4
CompatibilitySolid state relay
Maximum sink current0.5 A
Maximum switching voltage50 V
Maximum update ratedepending on EtherCAT master
Isolation voltage peak1000 V Isolated common GND
Additional Specifications
Input connectorsTerminal block (3 x 2 pole, 2 x 12 pole, 1 x 8 pole) OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Power outmax. 2 A (unprotected)
Power consumption1.8
Weight184 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
¹ Not supported on the OBSIDIAN
Rev: 1668186000

Технические характеристики IOLITE-16xAO

Analog Output
Output typesVoltage
Number of channels16
Output connectorTerminal block
DAC Resolution16-bit
Update Rate20000 S/s (see 1)
Update Rate
Full Scale Output Range±10 V (see 2)
Accuracy (typ.)0.05 % ±1.5 mV (0 to 20 mA load)
Temperature gain drift (typ.)±10 ppm/K
Temperature offset drift (typ.)±5 uV/K
Output impedance< 1 Ω DC
Minimal load resistance500 Ω load @ 10 V output
Settling time (0.05 % of set value)140 µs
Max slew rate0.20 V/µs
Max capacitive load (2 % overshoot)10 nF
Output protectionShort circuit protected
Current limit20 mA per channel (160 mA per module)
IsolationChannel to ground
Additional Specifications
Output connectorsTerminal block, 2 pole, 4 x 9 pole OMNIMATE SL 2.50 / BLF 2.50/180
Power supply9 - 48 V DC
Power outmax. 2 A
Power consumptionTyp. 4.5 W, Max. 8 W
Weight210 g
Slice Dimensions128.4 x 115.4 x 30.1 mm
Rev: 1603360800
1) Only asynchronous mode is supported in Dewesoft, function generator is not supported
2) Only DC output voltage, function generator not supported

Технические характеристики IOLITEi-4xCAN-FD

CAN ports specification
Number of ports4
Interface typeCAN-FD, CAN 2.0B
CAN 2.0B data rateUp to 1 Mbit/s (see 1)
CAN-FD data rateUp to 5 Mbit/s (see 1)
Special protocolsJ1939, XCP, OBDII
Galvanic isolationIsolated
Bus pin fault protection±36 V
Power specification
Power supply9 - 48 V DC
Maximum sensor power consumption 5 V / max. 250 mA (1.25 W) 12 V / max. 90 mA (1.1 W)
Maximum power consumption max. 2 W (no load)
Sensor supply isolationChannel to ground
Additional Specifications
RackIOLITEir-4xCAN-FD
Input connectorDSUB9
Power supply9 - 48 V DC
Weight310 g
Slice Dimensions128.4 x 118.4 x 30.14 mm
Additional Specifications
ModularIOLITEi-4xCAN-FD
Input connectorDSUB9
Power supply9 - 48 V DC
Weight550 g
Slice Dimensions136.75 x 115.0 x 35.0 mm
1) For more information please see the manual.
Вернуться к началу